Maxlogic ML-121X Istruzioni operative

COMMISSIONING, OPERATING AND MAINTENANCE MANUAL

MODEL: MAXLOGIC SERIES

SUB MODEL: INTELLIGENT ANALOGUE ADDRESSABLE

FIRE ALARM CONTROL PANEL

ML-121X

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 2

CONTENTS

1- INTRODUCTION .................................................................................................................................... 3

2- WARNINGS ........................................................................................................................................... 4

3- MOUNTING........................................................................................................................................... 4

4- PANEL INPUTS....................................................................................................................................... 5

4.1 Mains power supply ........................................................................................................................ 5

4.2 Batteries ......................................................................................................................................... 5

4.3 Detection Devices Inputs (Loop Lines) ............................................................................................. 5

4.4 Panel PC Connection ....................................................................................................................... 6

5- PANEL OUTPUTS ................................................................................................................................... 6

5.1 Sounder Outputs (4 Units) ............................................................................................................... 6

5.2 Auxiliary Power Supply Output (24 V DC) ......................................................................................... 7

5.3 Relay Outputs (3 Units).................................................................................................................... 7

6- PANEL BUTTONS AND INDICATORS ....................................................................................................... 8

6.1 Control Buttons ............................................................................................................................... 8

6.2 Front Panel Indicators ................................................................................................................... 10

6.3 Internal Indicators ......................................................................................................................... 11

7- PANEL FUSES ...................................................................................................................................... 11

8- POWERING THE PANEL ....................................................................................................................... 12

8.1. First Boot of Panel ........................................................................................................................ 12

8.2. Booting Previously Configured Panel............................................................................................. 16

9- FIRE EVENT MESSAGE FORMAT on PANEL LCD SCREEN ....................................................................... 17

10- FAULT EVENT MESSAGE FORMAT ON LCD SCREEN ............................................................................ 18

11- PANEL MENU .................................................................................................................................... 18

12- NETWORKING PRINCIPLES................................................................................................................. 23

13- TECHNICAL SPECIFICATIONS.............................................................................................................. 26

14- PANEL MODELS................................................................................................................................. 27

ANNEX-A PANEL DIMENSIONS AND MOUNTING HOLES .......................................................................... 28

ANNEX-B CONNECTION SCHEME............................................................................................................. 29

ANNEX-C PANEL SPARE PARTS ................................................................................................................ 30

ANNEX-D SERIAL COMMUNICATION CABLE............................................................................................. 31

ANNEX-E SCHEME OF MENU FUNCTIONS................................................................................................ 32

ANNEX-F NETWORK CONNECTION SCHEME ............................................................................................ 36

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 3

Maxlogic ML-121X Series

Intelligent Analogue Addressable Fire Alarm Control Panels

1- INTRODUCTION

Maxlogic ML-121X series intelligent analogue addressable fire alarm control panels are

provided with 0, 1, 2 loop options and 1000 user-defined zone capacity. Up to 127 analogue

addressable devices per loop are allowed to be connected.

Devices operating with VIP protocol such as Photo-Electric Smoke Detectors, Heat Detectors,

Multi-Sensor Detectors, Switch Monitor Modules, Relay Controller Modules, Sounder

Controller Modules, Loop-powered Addressable Sounders and Zone Monitor Modules are

compatible with ML-121X series control panels.

The project planning must be made carefully, in order not to have any difficulties when

commissioning the system. Zone location text (up to 40 characters including blank spaces) for

each device should be predetermined. Then, the devices should be categorized in zones

depending on the physical specifications of the building. After these steps, the panel can be

configured via the software program called ‘Loop Manager’.

The panel is equipped with 4 programmable and fault monitored 24 V DC 500mA sounder

outputs. Panel also contains 3 volt-free 30 V DC 1A relay outputs (fire relay, alarm relay, fault

relay) and a 24V DC 500mA auxiliary power supply output. Furthermore, 4 remote control

inputs (alarm, silence/sound alarm, reset and fault) exist in the panel.

ML-121X series fire alarm control panels have the optional functions described in TS EN 54-2

standards;

Sounder outputs

ML-121X series fire alarm control panels have also the supporting functions described in TS

EN 54-2 standards;

Network: The supporting function used to communicate in network.

NOTE: This user manual is valid for the panel models indicated in 14th section.

Producer-manufacturer or importer firms’ title, address, and telephone number

Manufacturer Firm:

MAVILI ELEKTRONIK TICARET VE SANAYI A.S.

SERIFALI MAHALLESI, KUTUP SOKAK NO: 27/1-2-4 UMRANIYE / ISTANBUL / TURKEY

TEL: +90 216 466 45 05 - +90 216 466 45 10

Service stations’ communication information that related spare parts have been

provided

Authorized Services:

MAVILI ELEKTRONIK TICARET VE SANAYI A.S.

SERIFALI MAHALLESI, KUTUP SOKAK NO: 27/1-2-4 UMRANIYE / ISTANBUL / TURKEY

TEL: +90 216 466 45 05 - +90 216 466 45 10

TEKSIS TEKNIK ELEKTRONIK SIS.TIC. VE SAN. LTD. STI.

SERIFALI MAHALLESI, KUTUP SOKAK NO: 27/3 UMRANIYE / ISTANBUL / TURKEY

TEL: +90 216 313 60 60 - +90 216 313 47 49

Expected operation life which has been determined and announced by related ministry

This device’s expected operation life is 7 years.

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 4

2- WARNINGS

The panel contains static-sensitive high quality electronic control equipment. Do not use the

panel before reading this manual.

In case of any fault, only the technicians of the manufacturer or technicians authorized by the

manufacturer should repair or maintain the panel.

The person who will operate the system should be well trained on powering and operating the

system.

Two years of warranty is valid from the production date as long as the system is used with

regard of obeying the rules, instructions and recommendations provided by the manufacturer.

Use the recommended cable types defined in this manual for cabling of panel power supply,

sounder power supply and detector line. Do not remove any connections and do not make any

connections while mains power supply is connected. Panel’s earth connection must be made

definitely.

Do NEVER apply 230V AC 50Hz mains power into the detectors and manual call points input

terminals, sounder line outputs and battery connection inputs.

This panel has been designed to operate on 230 V AC 50 Hz power supply. The protective

earth connection must be made definitely and the mains power supply must be presented

through the device via a fuse assigned only to this device. If the earth connection is not made

appropriately, all the conductive parts in the device may result in electrical leakage and this

may create hazard.

‘Automatic Learning’causes erasing of existing configuration data at the panel. Therefore, it is

recommended to download the configuration data to PC, before ‘Automatic Learning’.

3- MOUNTING

The chosen mounting site of the panel must be clean, dry, not subject to shock or vibration

and easily accessible. The temperature must be in between the temperature range of

-5C°and +50C°. The relative humidity must not be m ore than 95%.

The panel should be mounted on a flat surface in such a way that, the indicators should be at

the eye-level and must not be mounted near the sources of excessive heat or cold and inside

of any cabinet.

Uncover the panel via the allen key provided with the panel.

Panel cable entries from back and top of the panel are available for easy mounting. Mark the

position of the fixing holes according to the respective Annex-A, Figure-2; ensuring that the

wall is flat at the chosen location.

Screws or bolts of a minimum of 4mm diameter must be used to mount the cabinet in all four

mounting positions. Drill and plug the wall then fix the cabinet using all fixing points.

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 5

4- PANEL INPUTS

4.1 Mains power supply

The system is designed to operate with 230V AC 50Hz. Earth connections must be made to

earth terminal and earth resistor must be less than 10Ω. The mains supply of the panel must

be via an independent self-resetting fuse rated 230V AC 6A. This fuse must be separate from

the other fuses and a caution note should be written such as ‘ATTENTION! FIRE ALARM

CONTROL PANEL’S FUSE. DO NOT REMOVE’to ensure safe operation of the panel.

Recommended cable types are 3x2,5 NYM or 3x2,5 NYA. Connections must be done

according to Annex- B, Figure-1.

Do not connect or disconnect loops, mains supply input and PCB connections while the panel

is energized, to avoid an electric shock.

4.2 Batteries

Batteries provide continuity of operation during a failure of the mains power supply. The panel

uses 2 units of 12 V DC 7Ah dry type batteries. Battery connection scheme can be seen from

Annex-B, Figure-14.

4.3 Detection Devices Inputs (Loop Lines)

ML-121X series panels are produced with 0, 1, 2 loop models. Panels with

0 loops (no-loop) are used as repeater panels. Each loop is capable of hosting up to 127

addressable devices. Connection of loop line to the control panel must be as like in Annex-B,

Figure-7. A 0Ω resistor must be connected to the unused loops. Each device in the loop must

be addressed via MG-8200 Address Programmer depending on the architectural project of the

site.

The semi-duplex two-wire digital serial synchronous communication between the devices

connected to the loop and the fire alarm control panel is established by the VIP

communication protocol.

Short circuit isolators must be placed in such a way that more than 20 detectors and/or

manual call points shall not be out of service in case of any short circuit occurrence in the

loop.

The devices should be connected to a one-pair cable to create a loop and should turn back to

the panel from the last device.

The loop is energized from the ‘out’terminal of the panel and the turn back point toward the

panel is the ‘in’ terminal. In case of rupture or short circuit, the loop is energized from both the

‘in’ terminal and the ‘out’terminal. Thanks to this functionality; it is provided that the devices,

except from the detectors / buttons which are in failure, go on functioning properly while the

part in failure is isolated.

It should be used the short circuit isolator for each ‘in’ and ‘out’terminals. Thus, if any problem

occurs in between the part from any of the ‘in’ or ‘out’terminals to the first short circuit isolator

location, this part is isolated and the rest of the loop can go on functioning properly.

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 6

1x2x1,5+0,8J-Y(st)Y, 1x2x0,8+0,8J-Y(st)Y or 1x2x1,5+0,8J-H(st)H, 1x2x0,8+0,8J-H(st)H

coded cables should be used. While cabling (starting from Loop + terminal), cable’s earth line

must be connected to appropriate earth terminal in the control panel (See Annex-B, Figure-2).

This earth line should be installed throughout all detectors and call points. Earthing cables

should be wired after placing detectors and/or call points and line should be ended. When a

return is performed to (Loop -), earthing line should be done as it is shown in Annex-B,

Figure-2 and line is ended.

4.4 Panel PC Connection

4.4.1 PC Port

Cable connection between panel and PC for data communication is plugged into the PC

Socket which found on front panel of (See Annex-B, Figure-11). The communication cable

shown in Annex-D must be used for communication with computer.

4.4.2 Write Enable Switch

Write enable switch has two positions as “ON”and “OFF”. (Annex-B, Figure-8) When the

panel is energized while the switch is OFF, the panel runs previously saved data. When the

panel is energized while the switch is ON, panel operation modes appears on the screen.

More details are provided in Section-8.

4.5 Remote Control Inputs

There are remote control inputs on the panel which are likely to control the panel remotely by

the help of any remote button. One terminal of the button is connected to the desired input

and other one is connected to GND. (See Annex-B, Figure-6). It should be used the cable with

this code; 2x1,5 N2XH or 2x1,5 NYY for remote control input line.

AL : Reactivates alarm condition, sounders and relays which was silenced and positioned

by Silence Alarm.

FLT : Activates fault condition.

RS : Resets the panel.

SIL : Silences sounders and returns the relays to their initial position.

5- PANEL OUTPUTS

5.1 Sounder Outputs (4 Units)

The panel has 4 sounder outputs rated 24 V DC 500mA. In order to monitor the line against to

open or short circuit conditions, normally 16 V DC reverse voltage is seen from the sounder

outputs. During fire alarm outputs are driven by 24 V DC (Annex-B, Figure-4). Current driven

more than 0.5A leads the panel into the fault condition.

2x1,5 N2XH or 2x1,5 NYY cable should be used for the sounder line. 10KOhm resistor,

located on sounder outputs from factory default is used as end-of-line resistor and must be

connected to the end of the sounder line. Otherwise, open circuit fault is monitored on the

sounder line of panel. In case of any open circuit or short circuit faults occurred, it can be

displayed on the screen of panel with the line number.

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 7

5.2 Auxiliary Power Supply Output (24 V DC)

The panel is equipped with an auxiliary 0.5А24 V DC power supply output. Exceeding this

level causes fault condition. It can be used for supplying power to peripheral devices.

2x1,5 N2XH or 2x1,5 NYY cables should be used for external power supply line. In case of

mains power supply failure, the batteries provide power supply to the output (24 V DC).

(Annex-B, Figure-3).

5.3 Relay Outputs (3 Units)

The panel has 3 units of relay outputs with volt free changeover contacts rated 1A 30 V DC.

These volt-free outputs; fire relay (normally non-energized), alarm relay (normally non-

energized) and fault (normally energized). (Annex-B, Figure-5). 2x1,5 N2XH or 2x1,5 NYY

cable should be used for relay output line.

5.3.1 Fire Relay : The output is activated on any fire event and it can be used to trigger

any other system. The output is returned to its initial position only by pressing ‘Reset’button

on panel.

5.3.2 Alarm Relay : The output is activated on any fire event and it can be used to activate

any other system. The output is returned to its initial position only by pressing ‘Alarm Silence’

button on panel. If a new alarm occurs, Alarm relay reactivates.

5.3.3 Fault Relay : The output is activated on any fault event, changes its contact in case

of mains failure. The output returns to its initial position, if fault condition is removed and the

‘Reset’button on the panel is pressed.

Important notice : Fire alarm panel relays operate as signal-based relays. If these relays

will activate any other devices as like control relays, then a contactor should be used between

the relay and device. In case of high current driven applications, the relay outputs can get

damage if there is no contactor. This situation is not subjected to the warranty condition.

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 8

6- PANEL BUTTONS AND INDICATORS

6.1 Control Buttons

While control panel is in normal operating condition, it is in ‘Access Level 1’. In Access Level

1, the buttons; Silence Buzzer, Lamp Test, More Fires, More Events can be used.

The Silence Buzzer, Lamp Test, More Fires, More Events Buttons can be used in Access

Level 1.

Passing ‘Access Level 2’ enables to use other buttons. In order to pass ‘Access Level 2’

button control key is brought to enable position. To prevent unauthorized access, button

control key must always be kept as disable position while panel operating in normal condition.

Evacuate : Used for the purpose of evacuation. It requires to be programmed by

the Loop Manager Program.

Pressing this button:

- Buzzer sounds.

- Sounders ring.

- Alarm and fire relays get activated.

- Fire LEDs and Evacuation LEDs illuminate.

Alarm : Pressing Alarm button reactivates the sounders and relay outputs

which were silenced before.

Silence Alarm : This button is used to silence an alarm and bring relay outputs to their

old positions.

Silence Buzzer : This button is used to silence the internal buzzer which rings during fire

alarm or any fault condition occur in the system.

Lamp Test : It is used to check all the LEDs and LCD screen of the panel whether

they are operate normally or not.

Reset : Resets all existing fire and fault events in the system. Fire and Fault

relays are brought to normal position (if fire and fault condition is not proceeding).

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 9

More Fires : Among existing events, if there are more than one fire event, this

button is used to see fire events in the system.

The latest fire event remains at the bottom of the LCD screen. Pressing ‘More Fire’ button

shows all the fire events at the upper part of the LCD screen.

Z o n e s I n A l a r m : 1 A l a r m : 2 F a u l t : 1

* F I R E : M G 6 2 0 8 8 - W a y S w . M o n . Z o n e : 1 *

P : 0 L : 1 A : 2 8 M L - 1 2 X X R e - i n i t i a t e d

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

* F I R E : M G 6 2 0 8 8 - W a y S w . M o n . Z o n e : 1 *

P : 0 L : 1 A : 2 8 M L - 1 2 X X R e - i n i t i a t e d

More Events : If more than one event occurs, it is possible to see all other events by

pressing this button. Pressing this button categorizes the events. It is possible to check other

events by pressing ‘1(UP)’, ‘3(DOWN)’buttons. To see the desired event category, press the

button with number ‘2 (RIGHT)’. To get back to the main category press ‘EXIT’button.

Event categories as below;

Fires

Tech. Alarms

Announce Event

Informations

Evacuates

Tech. Faults

FF Tel. Event

Disablements

Faults

Alerts

Analog Event

Test

Pre-Alarms

Securities

Internal Events

Direction buttons:

Button number ‘1’ : It is used to go upward in the panel’s main menu screen and in the

‘More Events’ menu.

Button number ‘2’: It is used to select the desired feature in panel’s main menu and

desired category in ‘More Events’ screen and go to right direction.

Button number ‘3’ : It is used to go downward in the panel’s main menu screen and More

Events menu.

Button number ‘4’ : It is used to go back to previous menu and go to left direction.

Enter : Enter Button is used to see the menu screen and select the desired

feature inside the menu.

Exit : It is used to go back to previous menu when LCD screen shows main

panel menu or go back to categories menu from the selected category.

Note: Menu features are described in detail in the 11th section of Panel menu. To see the

transitions among menu features please check ANNEX-E Scheme of Menu Functions.

W/Dog Reset : Used for elimination error in case of ‘System Fault’LED illuminates.

However, if the LED illuminates because of any fault in the central microprocessor preventing

the program to run; the button will be useless for this situation (ANNEX-B, Figure-9).

Microprocessor Reset: Microprocessor can be reset by pressing the ‘Microprocessor Reset’

button. (ANNEX-B, Figure-13)

LCD Lighting : Used to adjust the LCD display contrast with the aid of trimpot

(ANNEX-B, Figure-10).

KK-641.002 Rev.No:1 01.08.12 ML-121X User Manual Page | 10

6.2 Front Panel Indicators

FIRE : Fire LEDs illuminate in two conditions; if there is a fire situation in the

system or in case of pressing Evacuate button. Each one of these conditions makes the LEDs

illuminate in ‘Red’ colour.

Power On : Panel is energized and operates normally. It illuminates as ‘Green’

continuously.

General Fault : If any fault occurs during operation. It illuminates with the specified

respective faults such as power fault. It illuminates as ‘Yellow’.

Power Fault : It indicates that there is a mains power failure or a problem of battery.

It illuminates as ‘yellow’ and related fault condition can be viewed on the LCD screen.

System Fault : Main microprocessor fault. It Illuminates as ‘Yellow’.

Sounder Disabled : It shows that the sounder outputs on the panel has been disabled and

illuminates as ‘yellow’.

Disablement : If any device or line disabled in the system this LED illuminates as

‘Yellow’.

More Fires : It indicates the presence of more than one fire in the existing event list

of the system. It illuminates as ‘Yellow’.

Evacuate : It indicates that the Evacuate button is pressed. The Evacuate button

must be programmed by Loop Manager Software Program. It illuminates as ‘Red’.

Alarm : It indicates that the alarm button is pressed, it illuminates as ‘Yellow’.

Alarm Silenced : This led shows that incoming alarms are silenced by pressing ‘Alarm

Silenced’ button. It illuminates as ‘Yellow’.

Buzzer Silenced : It indicates that the Buzzer Silenced button is pressed and it

illuminates as ‘Yellow’.

Zone Disablement : It indicates that one or more zones are disabled from the panel menu.

It illuminates as ‘Yellow’.

More Events : If there is more than one event in the system this LED illuminates as

‘Yellow’.

Indice

Altri manuali Maxlogic Pannello di controllo

Maxlogic

Maxlogic ML-322 Istruzioni operative

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche