Maxsys PC4204CXCF Manuale utente

PC4204CXCF

Power Supply / Relay Output / Combus Repeater Module

v 3.0 • Installation Instructions

1.0 Introduction

The PC4204CXCF is a power supply/relay output module for use

with PC4010CF and PC4020CF Maxsys fire/security systems. The

PC4204CXCF provides one power output for system devices and 4

programmable relay outputs. Relay 1 can be used to repower the

Combus. This module will also regenerate the Combus data signal to

allow for longer wire runs. This module is not to be used for fire alarm

bells.

The PC4702BP must be used.The PC4702BP must be used.

The PC4702BP must be used.

NOTE:NOTE:

NOTE: The PC4204CXCF is the only power supply which can repower the

Combus on PC4010/PC4020CF systems. See the control panel

Installation

Manual

for details.

The PC4204CXCF is the only power supply unit for PC4010CF/PC4020CF

system devices which has UL/NFPArequired supervision integrated

into the control panel. Primary power for the PC4204CXCF must be

connected to the same branch circuit as the PC4020CF.

2.0 Specifications

• Transformer 16.5VAC - 40VA (DSC Part No. PTD1640U)

• Transformer 16VAC-80VA (BEI Part No. AS16N)*

*For commercial fire use only the 80VA transformer

• Backup battery: 4Ah to 38Ah sealed lead-acid (not provided)

• Current draw: 30 mA (from Combus)

• Connects to control panel via 4-wire Combus

• Selectable battery charging current (400mA or 1.2A)

• Auxiliary power output: 900mA, 12VDC (nominal)

• 4 programmable relay outputs: Form C; contact rating: 2A, 30VDC

• Tamper connection

3.0 Installing the PC4204CXCF

3.1 Unpacking

The PC4204CXCF package should include the following parts:

• One PC4204CXCF circuit board

• One PC4055CR cabinet with space for one 38Ah battery

• Five plastic standoffs

• 16VAC, 80VA transformer

3.2 Mounting

The PC4204CXCF should be located inside the PC4055CR cabinet,

mounted in a dry, secure location.

NOTE:NOTE:

NOTE: The PC4204CXCF must be

installed within a fire enclosure, as defined in EN60950. The cabinet must

comply with the battery manufacturer’s installation instructions.

NOTE: The cabinet should be mounted in a safe and reliable manner. A

safety factor of 4 or higher must be provided.

Perform the following steps to mount the unit:

1.1.

1. Press the five plastic standoffs through the mounting holes at the

back of the cabinet.

2.2.

2. Secure the cabinet to the wall in the desired location. Use

appropriate wall anchors when securing the cabinet to drywall,

plaster, concrete, brick or other surfaces.

3.3.

3. Press the circuit board onto the plastic standoffs to secure the

module to the cabinet.

Once the unit is mounted, wiring may be completed.

3.3 Installation and Wiring

NOTE: The PC4204CXCF is intended to be PERMANENTLY

CONNECTED and should be installed by service personnel only.

Before beginning to wire the unit, ensure that all power (AC

transformer and battery) is disconnected from the control panel.

Perform the following steps to complete wiring:

1. Connect the four panel-originating Combus wires to the

PC4204CXCF. Connect the red, black, yellow and green Combus

wires to the RED, BLK, YEL and GRN Combus In terminals,

respectively.

If Relay 1 is being used for Combus power, connect the Combus

wires according to the diagram below. Note that for this option,

jumper Con3 must also be set for “Repower Relay 1.”

Additional modules repowered by the PC4204CXCF should have

the black, yellow and green Combus wires connected to the BLK,

YEL and GRN Combus Out terminals respectively.

2. Complete all output wiring.

3. Connect the external tamper switch, if used.

Consult the wiring diagrams for further information.

Current Ratings

In order for the system to operate properly, the power output of the

PC4204CXCF module cannot be exceeded. For the maximum available

AUX current, refer to the Battery Selection Charts based on 24h/60h

standby power time. The maximum available AUX supply current is

dependent on the size of the transformer used as well as the selected

battery charge current. Use jumper J2 to control the supply current

(see below).

MaximumMaximum

Maximum AUX Supply CurrAUX Supply Curr

AUX Supply CurrAUX Supply Curr

AUX Supply Currentent

entent

ent

BAA

ATTERTTER

TTERTTER

TTERYY

YCC

CHARGEHARGE

HARGEHARGE

HARGE 40V40V

40V40V

40VAA

A80V80V

80V80V

80V

CURRENTURRENT

URRENTURRENT

URRENT TT

TRANSFORMERRANSFORMER

RANSFORMERRANSFORMER

RANSFORMER TT

TRANSFORMERRANSFORMER

RANSFORMERRANSFORMER

RANSFORMER

HI-CHRG (400mA) 600mA 900mA

HI-CHRG (1.2A) 150mA 900mA

OFF

NOTE: All devices connected to the AUX output must be UL Listed for fire

protective signaling service as well as burglary protective signaling service.

NOTE: When using the PC4204CXCF to repower additional Combus modules,

current calculations must be made to ensure that the maximum AUX supply

current is not exceeded.

Module Ratings

The current draw of compatible modules is listed below:

DeviceDevice

Device Current Draw (mA)Current Draw (mA)

Current Draw (mA)Current Draw (mA)

Current Draw (mA)

Keypad (LCD45XX) ............................................................................. 50

PC4108A Zone Expander .................................................................... 30

PC4116 Zone Expander ....................................................................... 30

PC4164 Wireless Receiver ................................................................. 110

PC4701 Fire Module ............................................................................. 35

PC4702BP Dual Bell Output Module ................................................. 75

PC4204CXCF Relay Output Module ................................................. 30

PC4216 Low Current Output Module ............................................... 15

ESCORT4580 Audio Assistant ..........................................................150

PC4400 Printer Module .......................................................................30

PC4820 Access Control Module ......................................................... 35

PC4936 Audio Interface Module ........................................................65

PC4401 Serial Interface Module ......................................................... 35

PC4850 Telephone Entry Module .....................................................135

Calculating Total Current Requirement

Once you have determined which modules will draw power from the

main panel, use the following chart to calculate the Combus current.

Combus Current Calculation Chart

Item Current (mA) x Quantity Total (mA)

Keypad 50 x

PC4108A* 30 x

Current required for connected devices =

PC4116* 30 x

Current required for connected devices =

PC4164 110 x

PC4701 35

PC4702BP 75 x

PC4204CXCF 30 x

PC4216* 15 x

Current required for connected devices =

Escort4580 150

PC4400/4401 30/35 x

PC4820 35 x

PC4850 135 x

PC4936* 65

Alt. Comm.

Total Combus Currotal Combus Curr

otal Combus Currotal Combus Curr

otal Combus Current =ent =

ent =ent =

ent =

NOTE: * These modules draw current from the Combus to power devices

external to the module. This current must be added to the total Combus current.

See manufacturer’s specifications for the current draw of each device. Each

LED assembly draws up to 20mA of current.

Combus Operation and Wiring

The Combus is used by the control panel and the modules to

communicate with each other. When the PC4204CXCF is used to

repower the Combus, please refer to the wiring diagram for the exact

wiring procedures. Note: Please follow the diagram exactly.

Modules can be home-run, connected in a daisy chain or T-tapped

anywhere on the Combus.

The following rules MUST be followed when wiring the Combus:

1.1.

1. The Combus must be run in minimum 18-gauge wire.

2.2.

2. No module can be more than 1000' (305m) in cable length from

the PC4204CXCF (see below ‘Combus Extensions’).

3.3.

3. Shielded wire should only be used in areas that present excessive

RF noise or electromagnetic interference. If shielded wire is used,

the maximum distance a module can be located from the

PC4204CXCF is significantly reduced. Check the capacitance rating

of the wire to calculate the maximum distance (see “Capacitance

Limits” below). NOTE: Shielded wire is not recommended.

4.4.

4. The total capacitance of the Combus wiring must not exceed 80nF

between the control panel and PC4204CXCF module or between

two PC4204CXCF modules (see “Capacitance Limits” below).

Long Distance Combus Extensions

The length of Combus from a PC4204CXCF Combus Regenerator can

be extended beyond 1000’, providing the following conditions are met:

• Combus must be regenerated and repowered at both ends of the wire

run using PC4204CXCF and modules.

• No other modules are to be connected along the long distance wire run.

• A maximum distance of 4000’ can be achieved between two

PC4204CXCF devices. To extend further, additional PC4204CXCF

devices should be used.

NOTE: The wiring used to connect this equipment must be insulated with

PVC, TFE, PTFE, FEP, neoprene or polymide.

Line Loss

When current is drawn through a piece of wire, voltage will be lost

due to the wire’s resistance. This voltage loss must be considered for

all installations.

To ensure proper operation, at least 12.5VDC must be applied to all

modules on the system (when AC is applied and the battery is fully

charged). If less than 12.5VDC is applied, system operation will be

adversely affected.

To correct the problem, try any or all of the following:

1. Connect another PC4204CXCF power supply near the module to

provide power to the Combus.

2. Reduce the length of the Combus run to the module.

3. Increase the gauge of wire.

Capacitance Limits

An increase in capacitance on the Combus will affect data transmission

and will cause the system to slow down. Capacitance will increase for

every foot of wire added to the Combus. The capacitance rating of the

wire used will determine the maximum length of the Combus, between

two PC4204CXCF Combus Repower/Regenerator modules.

The following chart indicates the total Combus wire allowed depending

on the capacitance rating of the wire used:

Wire Capacitance per

1000’(300m)

TOTAL Combu s Wire

Length

15nF 5300’/1616m

20nF 4000’/1220m

2 5n F 32 00’ /97 6m

3 0n F 26 66’ /81 0m

3 5n F 22 80’ /69 3m

4 0n F 20 00’ /60 8m

Wires run in parallel also increase Combus capacitance. For example,

when using 20nF wire, the following would be some of the

combinations allowed:

• Four wire runs at 1000'/305m each

• Six wire runs at 666'/203m each

• Eight wire runs at 500'/152m each

• 10 wire runs at 400'/122m each etc…

Contact the wire manufacturer for the capacitance ratings of the wire

being used.

3.4 Regenerating Combus

This module will regenerate the Combus signal as it passes from one

side to the other. The LEDs on the module will illuminate whenever

there is activity on either side of the input or ouput of the module.

LED 1LED 1

LED 1 illuminates when the module transmits data on ‘Combus In’

LED 2LED 2

LED 2 illuminates when the module transmits data on ‘Combus Out’

The PC4204CXCF module will isolate ‘Combus In’ from any short

circuit problems on ‘Combus Out’. In the event of a problem, the

PC4204CXCF module will generate a module fault along with the

modules on the disabled Combus. This information can be used to

determine which section of Combus is disabled on the system.

When connecting the PC4204CXCF to the Combus, care must be taken

to ensure that the ‘Combus In’ terminals are connected to the wires

originating from the control panel (or a module that may be situated

between the PC4204CXCF and the control panel).

3.5 Applying Power

NOTE: Do not connect power until all wiring is complete.

After all wiring is completed, apply power to the control panel.

Connect the battery leads to the battery, then connect the AC

transformer. Then, connect power to the PC4204CXCF: first connect

the battery leads, then the AC transformer.

12V 38Ah Battery

(Not supplied)

PC4204CX

PC4055C/CR

Cabinet

Power limited access Power limited access

IMPORTANT: A minimum of 1/4" (6.4mm) separation

must be maintained at all points between power limited

wiring and all other non-power limited wiring and

connections. Wire entry for power limited wiring must

be separate from non-power limited wiring.

For more information on control panel power specifications, see the

control panel

Installation Manual

NOTE: It is the installer’s responsibility to provide adequate protection for

the transformer used in the primary and secondary circuit according to the

rated current of the transformer. The transformer used must be Class2, Fail

Safe as defined within EN61558-1 and must meet the applicable requirements

of the EN60950 Standard. A readily accessible disconnect device must be

incorporated into the fixed wiring and should disconnect both poles

simultaneously. The wiring connected to the PC4204CXCF must be

mechanically protected, routed, supported, clamped or secured in a manner

that prevents excessive strain on wire and terminal connections, loosening of

terminal connections and conductor insulation damage.

NOTE: Do not connect fully discharged (less than 10V) or damaged batteries

to the PC4204CXCF.

3.6 Battery Selection Charts

The charts below are to determine the battery required to support the

AUX output of the module for either 24 hours or 60 hours standby,

followed by 15 minutes of alarm.

38Ah

Battery Selection for 24hr Standby and 15-minute Alarm

Battery Selection for 60hr Standby and 15-minute Alarm

24 Hr Standby Current (mA)

60 Hr Standby Current (mA)

150

60 125 190 220 285 380 600

300 450 550 700 940 1000

NOTE: If the required Ah (Amp hours) cannot be achieved with one battery,

two batteries may be connected in parallel to obtain a higher Ah rating.

Toronto, Canada • www.dsc.com

Technical Support 1-800-387-3630

Printed in Canada 29005815 R005

Direct all comments and suggestions

concerning DSC publications to

[email protected]

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security

Controls Ltd. could void your authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed and

used properly, in strict accordance with the manufacturer’s instructions, may cause

interference to radio and television reception. It has been type tested and found to

comply with the limits for Class B device in accordance with the specifications in

Subpart “B” of Part 15 of FCC Rules, which are designed to provide reasonable

protection against such interference in any residential installation. However, there is

no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause interference to television or radio reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Re-orient the receiving antenna

•Relocate the alarm control with respect to the receiver

•Move the alarm control away from the receiver

•Connect the alarm control into a different outlet so that alarm control and receiver

are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/televi-

sion technician for additional suggestions. The user may find the following

booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/

Television Interference Problems”. This booklet is available from the U.S. Gov-

ernment Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4.

PC4204CF Outputs Module Number: PC4204CFModule Number: PC4204CF

Module Number: PC4204CFModule Number: PC4204CF

Module Number: PC4204CF # I

______I

______I (1-16 = XX)

Partition

Output 1 2 3 4 5 6 7 8 Zone Schedule # Pulse Timer

[000702XX01] PC4204CF Relay 1 I

______I

______II

______I

______II

______I

______II

______I

______II

______I

[000702XX02] PC4204CF Relay 2 I

______I

______II

______I

______II

______I

______II

______I

______II

______I

[000702XX03] PC4204CF Relay 3 I

______I

______II

______I

______II

______I

______II

______I

______II

______I

[000702XX04] PC4204CF Relay 4 I

______I

______II

______I

______II

______I

______II

______I

______II

______I

4. Enrolling the Module

Once connected, the module must be enrolled on the system. To enroll

the module, perform the following:

1. Enter Installer Programming by pressing [*] [8] [Installer Code].

2. Scroll to “Module Hardware” and press the [*] key.

3. Scroll to “Enroll Module” and press the [*] key.

4. Scroll through the different modules until “PC4204” is displayed.

Press the [*] key.

5. The message “Create Tamper on Desired Unit” will be displayed.

To create the required tamper, secure the tamper zone on the

module and then open it. The transition from secure to violated

enrolls the module. After this is done, the keypad will display

the module number and will confirm enrollment (e.g., “PC4204

Mod 01 Enrolled”).

For more information regarding module enrollment, see the control

panel

Installation Manual

5. Programming the Module

To access PC4010CF/PC4020CF programming, enter [*][8] followed

by the Installer Code. Each relay output must be programmed. Please

see the control panel

Installation Manual

and

Programming Worksheets

for a detailed list of output options.

NOTE: Relay 1 must not be programmed if used for Combus power. Ensure

that Jumper CON3 is set to “Repower Relay1.”

NOTE: PC4204CXCF relay outputs cannot be used for fire system notification

appliances.

Altri manuali Maxsys Ripetitore

Maxsys

Maxsys PC4020 Manuale utente

Manuali Ripetitore popolari di altre marche

Gigaset

Gigaset 108 Manuale utente

Ace TECHNOLOGY

Ace TECHNOLOGY USR-1900A Manuale utente

Kenwood

Kenwood TKR-750-850 Manuale elenco delle parti

Asus

Asus RP-AC51 Manuale utente

Exibel

Exibel HRP0101 Manuale utente

Kidde

Kidde Vega Manuale utente

Telcosat

Telcosat RBB 850 Guida all'installazione

York

York Universal LINC485 Manuale utente

MIKOM

MIKOM MRx01B Power Series Manuale utente

Simrad

Simrad RD 301 Manuale utente

Tait

Tait TB7304 Manuale utente

R-tron

R-tron RSN-CDMA-37-C Manuale utente

Inventronics

Inventronics DALI REPEATER SO Manuale utente

XFP

XFP 16 Manuale utente

Andrew

Andrew MRx18 Manuale utente

COMBA

COMBA RXA3748 Manuale utente

ADRF

ADRF SDR-ICS-43 Manuale utente

Teltonika

Teltonika WRP100 Manuale utente