Mazda C9F2 V6 572 EU Manuale utente

Common-1

iPod INTEGRATION MODULE

INSTALLATION INSTRUCTIONS

Vehicle: Mazda2, Mazda3, Mazda5, Mazda6, Mazda RX-8

Mazda MX-5, Mazda CX-7, Mazda BT-50,

New Mazda2, New Mazda6

Parts number：C9F2 V6 572 EU

Thank you for purchasing a genuine Mazda accessory.

Before removal and installation, be sure to thoroughly read these instructions.

Please read the contents of this booklet in order to properly install and use the iPod integration module.

Your safety depends on it.

Keep these instructions with your vehicle records for future reference.

Note:

zThere are several WARNING and CAUTION sections in this booklet concerning

safety when installing or removing the iPod integration module. Always read and follow

them in order to prevent injuries, accidents, and possible damage to the vehicle.

WARNING: Indicates a situation in which serious injury or death could result if the

warning is ignored.

CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could

result if the caution is ignored.

zDo not modify the iPod integration module.

zDo not install the iPod integration module in any way other than described in the following

instructions.

zIf in any doubt, please ask your Mazda dealer to install the accessory in order to prevent

errors in installation.

zIf you have any questions about the use of the accessory, ask your Mazda dealer for proper

advice before using it.

zMazda and its suppliers are not responsible for injuries, accidents, and damage to persons

and property that arise from the failure of the dealer or installer to follow these instructions.

zTo ensure safety and reliability of the work, installation, removal and disposal work by an

Authorized Mazda Dealership is recommended.

zBe careful not to lose removed parts, and be sure that they are kept free from scratches,

grease or other dirt.



* iPod is a trademark of Apple Computer, Inc., registered in the United States and other countries.



To the deale

Please turn over these instructions to the customer after installation.

To the customer

zKeep these instructions after installation. The instructions may be necessary for installing other

optional parts or removal of this accessory.

zShould the vehicle or this accessory be resold, always leave these instructions with it for the next

owner.

1ED6P11A13300

Common-2



PARTS LIST

ziPod integration module （Part No. C9F2 V6 572 EU）

Parts Part Name Qty Parts Part Name Qty Parts Part Name Qty

iPod

Integration

module 1 Harness (c) 1

iPod

connection

cable 1

Tie wrap

Large 300 mm

Small 100 mm

L 7

S 10

Double-sided

adhesive tape

（44×118mm）2

Pad protector

（50×100 mm）10

※ A separately purchased "Selector box" (TD13 79 CFZ) is necessary when installing the iPod integration module

to vehicles equipped with anAUX terminal.



☆Flathead screwdriver

☆Socket wrench ☆Pliers ☆Soft cloth

☆Phillips screwdriver ☆Cutter knife ☆Scissors ☆Vinyl tape

☆Fastener remover ☆Mat



2. REQUIRED TOOLS

•Before installation, verify that the kit includes all the following parts and that they are free of dirt, scratches,

or damage.

NOTE

1. PARTS

3. BEFORE INSTALLATION

•To prevent short related accidents while performing procedures, disconnect the negative battery cable

before beginning any work.

•When disconnecting the connector, hold the connector itself to remove while pressing the connector lock.

•Do not apply excessive force to the wiring harness as it could cause an open circuit.

•When locking connectors, listen for a click that will indicate they are securely locked.

•Be careful not to pinch the wiring harness. Otherwise, the wiring harness could be damaged.

•When removing and installing vehicle parts, make sure they are clean with no scratches. Also, be sure to

cover the vehicle body with protectors or mats when removing/installing parts to prevent scratches and dirt.

CAUTION

•Refer to the applicable Workshop Manual for removal and installation of vehicle parts. Not following the

procedures for removal/installation in the Workshop Manual could result in an accident or vehicle

malfunction.

•When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased.

Before performing work, record the content of the memory.

NOTE:

Common-3

zInstallation of iPod integration module only <For vehicles without AUX terminal>

iPod (On-market product )

Audio unit

iPod

integration module

Harness

(

)

iPod connection cable

16-

in connecto

4. CONNECTION DIAGRAM

Common-4

ziPod integration module and selector box installation <For vehicles equipped with an AUX terminal>







5. CAUTIONS ON CONNECTION

iPod (On-market product)

iPod

integration module

iPod connection cable

Audio unit

Selector Box

Harness (a)

Harness (b)

Harness (c)

AUX

16-pin connector

zWhen connecting a connector, be sure to insert it straight along the guide.

The connector terminal may be bent if inserted at an angle.

CAUTION

■Installation instructions (For Mazda2 only)

Mazda2－1

Negative battery terminal disconnection

1. Disconnect the negative battery cable and wrap its terminal with tape to insulate it.

Column cover removal (upper and lower)

1. Remove the ignition key knob.

(Vehicles with advanced keyless system only)

2. Pull the upper column cover upward and remove it.

3. Remove the bolts (2) and screw (1), then remove the

lower column cover.

Lower panel removal

1. Pull the lower panel down and outward and disengage hooks

A (2 locations).

2. Pull the lower panel downward at an angle of 20 degrees from

the horizontal and disengage clips B (2 locations).

Console removal

1. Insert a flathead screwdriver wrapped with protective tape into

notch A in the cover and disengage hooks B.

2. Disengage hooks C while lifting up the cover in the direction of

the arrow.

3. Remove the shift knob. (MTX vehicles only)

4. Remove the screws and fasteners, then remove the console.

Column cover

(upper)

Bolt Screw

Column cover

(lower)

Vehicle

front

IG key knob

Column cover

(lower)

Lower panel

Clip B

Hook A Vehicle

front

Console

Ａ

Vehicle front

Cover Hook

Fastener

Screw

Hook C

Hook B

Ａ

ＢＢ

Ｃ

Shift knob

1. VEHICLE PARTS REMOVAL



short circuit while performing work may cause damage to parts, electric shock or other injury. Be sure to

disconnect the negative battery cable and do not allow the terminal to contact any other parts.

WARNING

 The procedure described here is for a right-hand drive vehicle, however, the procedure is the same for the

left-hand drive vehicle.

NOTE

■Installation instructions (For Mazda2 only)

Mazda2－2

Center panel module removal

1. Remove the knobs (3). (Vehicles with manual A/C only)

2. Remove the screws (2). (Vehicles with manual A/C only)

3. Remove the bolt (1) shown in the figure.

4. Remove the ashtray.

5. Pull the center panel outward from part A and

disengage clips B (8 locations).

6. Disconnect the connector and the antenna plug, then

remove the center panel module.

Glove box No. 1 removal

1. Remove the fasteners (3).

2. Pull glove box No. 1 outward, disengage the clips (3

locations) from the instrument panel, then remove it.

Glove box No. 2 removal

1. Move the stopper inward and remove.

2. Pull down glove box No. 2, disengage the clips (2 locations)

from the instrument panel, then remove it.

Clip x 3

Fastener x 3 Glove box No. 1

Vehicle

front

Clip

Stopper

Center panel module

Connecto

Clip B

Bolt

Ｂ

Center panel module clip position

Sectional

view

Ｂ

ＢＢ

Ｂ

Screw

shtra

Knob

ntenna

plug

Vehicle

front

■Installation instructions (For Mazda2 only)

Mazda2－3

WIRING <Installation of iPod connection adapter only>

iPod connection cable

○Ｂ

○Ａ

Vehicle front

Pad protecto

Vehicle front

Harness (c)

(To audio unit)

(Route harness so that

this part is approx. 170 mm)

○Ｃ

○Ａ

Put iPod connection cable in glove box

(Cable 30 cm from instrument panel)

Fit connector cover when

iPod is not connected

○

Ｂ

Vehicle

front

Harness (c)

(To audio unit)

iPod connection adapte

Loop redundant part of cable and tie it in two

locations, then secure with pad protectors

iPod connection cable

iPod

connection

adapter

Double-sided

adhesive tape

(Cut and affix)

Pad protecto

(Affix to member edges)

Pad

rotecto

Vehicle front

Pad protecto

(Cut and affix)

Tie wrap

(small)

○Ｃ

iPod

connection

adapte

2. INSTALLATION AND WIRING

 To prevent an open or short circuit in the wiring of the iPod connection adapter, be sure to route cables

avoiding sharp edges and burrs on the vehicle's sheet metal.

 To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is to be

adhered.

 After fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with

other parts causing failure or noise.

CAUTION

pprox.

170 mm

Pad protecto

■Installation instructions (For Mazda2 only)

Mazda2－4

1. Reconnect the negative battery cable.

3. CONNECTION CHECK

 Connect the negative battery cable carefully so that it does not interfere with other parts.

 If the battery is disconnected, the automatic full open/close feature of the power window is disabled.

This function can be reactivated using the following procedure.

1. Turn the ignition switch to the ON position.

2. Hold down the power window switch until the window is fully open.

3. Pull up the power window switch to close the window and continue to pull it up for about two seconds after it is full

closed.

4. If the feature does not function even after the ignition switch is turned off, contact an Authorized Mazda Dealer.

CAUTION

■Installation instructions (For Mazda3 only)

Mazda3－1



Negative battery terminal disconnection

1. Disengage tabs A (2 locations) and lift up the front of the battery

cover.

2. Pull the battery cover towards the front, remove pins B (2

locations), then remove the battery cover.

3. Disconnect the negative battery cable and wrap its terminal with

tape to insulate it.



Decoration panel removal

1. Open the glove box, pull the decoration panel outward in the

order shown (1 to 5), disengage clip A (1 location) and tab B (1

location), then remove the decoration panel.



Batter

(

－

)

terminal

Tab A

Pin Ｂ

Vehicle front

Battery cover

Vehicle

front

Clip A

Decoration panel

Tab B

1. VEHICLE PARTS REMOVAL

zA short circuit while performing work may cause damage

to parts, electric shock or other injury. Be sure to

disconnect the negative battery cable and do not allow the

terminal to contact any other parts.



WARNING

zThe procedure described here is for a right-hand drive vehicle, however, the procedure is the same for

left-hand drive vehicle.

NOTE

■Installation instructions (For Mazda3 only)

Mazda3－2

Glove box removal

1. Remove the screws (2).

2. Pull the glove box outward, disengage clips A (8 locations)

and tab B (1 location), then detach the glove box.

3. Remove the glove box light socket, then remove the glove box.



Center panel module removal

1. Remove the screws (2).

2. Pull the center panel module outward from the direction of

arrows ①and disengage clips A(2 locations).

3. Disconnect the connector and the antenna feeder, then

remove the center panel module.



Screw

Center panel module

Connector

Antenna feeder

①

①①

Clip A

Pull bracket

Vehicle front

Glove box

light socket

Glove box Clip A

Scre

Tab B

Indice

Altri manuali Mazda Adattatore

Mazda

Mazda C860-V6-572A Manuale utente

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente