MC Electronics AREA CONTROL MCK 3000 Manuale utente

AREA CONTROL MCK 3000

UNIVERSAL HECTARE COUNTER

FOR AGRICULTURAL MACHINERY

USE AND ASSEMBLY

INSTRUCTIONS

NO.201211MI

REV. 2

MCK 3000

Installation and use

MCK 3000

This product complies with the EMC requirements as defined by Directives

2004/108/EC and subsequent amendments

and refers to the applied Standard EN ISO 14982

Manufacture

: MC elettronica S.r.l.

Address

: Via E. Fermi, 450/486

Fiesso Umbertiano (ROVIGO) - ITALY

Tel. +39 0425 754713 Fax +39 0425 741130

E-mail: [email protected]

Internet: www.mcelettronica.it

Manual code

: 201211MI

Issued

: July 2012

Edition

: November 2020

MC elettronica S.r.l. is not obliged to give notice of any further modifications of the product.

The information given in this manual does not allow unauthorized personnel to tamper with the

product in any way.

The warranty on the equipment will no longer be valid if tampering should be detected.

 
 
Installation and use 3
MCK 3000 
 
Contents 
Rules and general warnings ................................................................................ 4 
1 Introduction....................................................................................................... 4 
2 Terms of the warranty....................................................................................... 5 
3 Service.............................................................................................................. 5 
General description .............................................................................................. 6 
System installation............................................................................................... 7 
1 Mounting the Monitor ........................................................................................ 8 
2 Sensor installation............................................................................................. 9 
2.1 Speed sensor installation........................................................................... 9 
2.1.1 Automatic calibration of the “C” parameter ......................................... 10 
2.2 Installing the mechanical counting sensor (if present) ............................. 11 
2.3 Installing the reflection seed sensor (if present)....................................... 12 
2.3.1 Adjusting the sensitivity of the seed sensor ........................................ 13 
3 Front view ....................................................................................................... 14 
3.1 Keyboard.................................................................................................. 15 
3.2 LCD Display............................................................................................. 16 
Accessories......................................................................................................... 16 
1 Standard accessories...................................................................................... 16 
Setting the work parameters.............................................................................. 17 
1 Setting the working width................................................................................ 17 
2 Setting the calibration of the feed-rate ............................................................ 17 
3 Setting the number of divisions of the total width............................................ 18 
4 Setting the hectare count mode ...................................................................... 18 
5 Programming the date/clock (if present) ......................................................... 19 
6 Check the speed sensor operating ................................................................. 20 
7 Check that the mechanical counting sensor functions .................................... 20 
8 Check that the seed sensor functions (if present)........................................... 20 
Operation............................................................................................................. 21 
Maintenance........................................................................................................ 23 
1 Routine maintenance...................................................................................... 23 
1.1 How to protect the main connector .......................................................... 23 
2 Extraordinary maintenance............................................................................. 23 
Troubleshooting.................................................................................................. 24 
Technical data..................................................................................................... 25 
1 MCK 3000 Area Control Technical data.......................................................... 25 
2 Accessory technical data ................................................................................ 25 
2.1 MC speed inductive sensor –code 481................................................... 25 

MCK 3000

Installation and use

MCK 3000

1. Rules and general warnings

1.1 Introduction

This instruction manual provides all specific information needed to know and correctly

use the equipment.

After buying the Monitor, read the manual carefully and refer to it any time you have

doubts on how to use the equipment or when you have to carry out maintenance

operations.

The manual must be kept on the machine or at least, when this is not possible, it

must be kept in a known place that is accessible for easy reference.

OTHER USE ISFORBIDDEN.

Installation and use 5

MCK 3000

1.2 Terms of the warranty

•SUBJECT OF THE WARRANTY: the warranty is applied to the product and to

those parts which are marked with the serial number or any other identification

number used by MC elettronica;

•DURATION OF THE WARRANTY: MC elettronica S.r.l. guarantees the MCK

3000 Monitor for a period of 1 year from the date of manufacture (printed on the

identification label on the rear of the monitor) and the accessories for a period of

1 year.

The warranty covers the product and any repairs carried out within the agreed

terms.

This warranty does not apply in the event of:

•accidental damage;

•improper use;

•changes which have not been agreed upon, improper installation (or set-up);

•damage caused when equipment not manufactured by MC elettronica,

which is mechanically or electrically connected to our instruments, breaks or

does not function properly;

•force majeure events (lightning, floods, fire or other causes which do not

depend on MC elettronica).

Repairs under warranty, which must be carried out in the laboratories of our

authorised centres, are entirely free of charge provided the equipment is directly

transported to said laboratories or sent carriage free. Transport costs and

ensuing risks are entirely borne by the Customer.

The above-mentioned warranty is valid unless otherwise agreed between MC

elettronica and the Customer.

Warning

MC elettronica declines any liability for damage or direct or indirect costs

caused by improper use or inability of the Customer to use the

equipment separately and/or together with other equipment.

1.3 Service

Service is available in all the countries where the Computer is officially supplied by

MC elettronica (during and after the warranty period).

Any kind of operation that is to be carried out on the MCK 3000 Monitor must be

done in accordance with the instructions stated in this manual or as agreed with MC

elettronica.

If not, the relative terms of the warranty might become null and void.

MCK 3000

Installation and use

MCK 3000

2. General description

The MCK 3000 Control Area is a universal hectare counter that can be installed on

any type of agricultural machine. With this instrument the following parameters can

be monitored:

•partial worked area;

•total worked area;

•distance travelled;

•speed (Km/h);

•forecast of the hectares that will be worked in an hour (only visible while you are

working).

The Monitor uses a speed sensor to carry out the functions described above, which is

to be installed on the machine wheel, and a mechanical counting sensor or a seed

sensor.

Figure 1. Example of application on standard combine harvester.

Mechanical

counting

sensor

Battery

Speed

sensor

Monitor

Installation and use 7

MCK 3000

3. System installation

Figure 2. Overall dimensions

MCK 3000

Installation and use

MCK 3000

3.1 Mounting the Monitor

To assemble the instrument operate as follows:

•on a flat surface inside the cabin of the vehicle, drill 2 holes (D. 9 mm)

aligned with those on the bracket (Figure 33 - ref. <A>) and, by means of

two screws (not supplied), securely fasten the bracket to the structure;

•fasten the Monitor to the bracket by screwing the supplied knobs (Figure 33

- ref. <B>) in the holes on the sides of the Monitor (Figure 33 - ref. <B1>).

N.B.:

we recommend installing the Monitor in front of the operator to make it

easier to use during the working cycle.

Figure 3. How to assemble the Computer.

Installation and use 9

MCK 3000

3.2 Sensor installation

The MCK 3000 Area Control can be equipped with 3 types of sensors:

•speed sensor (always present);

•mechanical counting sensor (for NON self-levelling combine harvesters, tractors,

etc.);

•reflection seed sensor (for self-levelling combine harvesters).

3.2.1 Speed sensor installation

You can install the speed sensor anywhere there is mechanical movement, on the

wheel (front or rear) of the agricultural machine/vehicle or by creating a metal

reference protruding by at least 7 mm ( Figure 4 ref. B2). We recommend installing

the speed sensor inside the wheel and placing the sensor head opposite the rim bolts

(Figure 4 –ref. A and B).

Set the gap between the sensor and the bolts at about 2/3 mm (Figure 4 –ref. B1).

Firmly fix the sensor bracket (supplied) to a secure part of the machine. Fix the

sensor to the bracket with the nut and the lock nut.

Warning

The sensor cable should be covered with a rubber sheath.

Figure 4. How to install the speed sensor.

Inner side of wheel

Speed sensor

Metal reference

MCK 3000

Installation and use

MCK 3000

3.2.1.1 Automatic calibration of the “C” parameter

Parameter “C” is automatically set by covering a fixed distance of 100 metres,

according to the following procedure:

▪With the Monitor on, press the key several times until the arrow on the

display lights up as shown in the figure: ;

▪press keys and simultaneously: 0 0 will appear on the Monitor;

•cover 100 metres and the display will show the pulse count (1..2..3, etc.); once

the 100 metres are covered, confirm with the key.

N.B.: it is recommended to perform the operation at least 2 times in a row, checking

that the detected value is always the same 1 pulse. If the difference is

greater, it means that the speed sensor is NOT positioned correctly.

Therefore, the assembly must be checked (see Figure 4)

Indice

Altri manuali MC Electronics Banco cassa

MC Electronics

MC Electronics UC 300 Manuale utente

Manuali Banco cassa popolari di altre marche

Omron

Omron H7CL Series Manuale utente

FAAC

FAAC XTR B Manuale utente

Olympia

Olympia NC-350A Series Manuale utente

Evco

Evco EV7001 Manuale utente

Record

Record FlowControl Manuale utente

XIA

XIA UltraLo-1800 Manuale utente

Cashmaster

Cashmaster Sigma 105 Manuale utente

Agilent Technologies

Agilent Technologies 53151A Manuale utente

Cashmaster

Cashmaster Sigma 105 Manuale utente

Tellermate

Tellermate TY Manuale per l'uso e la cura

HYOSUNG

HYOSUNG MX-4000W Manuale utente

Cashmaster

Cashmaster Sigma 105 Manuale utente

CCE

CCE 3200 Manuale utente

HP 53150A Series Istruzioni operative

HYOSUNG

HYOSUNG 1800CE Manuale utente

MZ electronic

MZ electronic EV-040 Manuale utente

Delfield

Delfield Shelleysteel SCFM-50 Manuale utente

TSI Instruments

TSI Instruments AEROTRAK+ 7201 Manuale utente