MCM Electronics IRIS 8 Manuale utente

Contents 1

Terms you may neeed to know 2

Keypad Lights 3, 4

Keypad Buttons 5

User Functions

Fully Arming the System - ON Mode 6

Partially Arming the System - Partial Mode 6

Isolate a section from being Armed 7

System OFF - Disarming the System 7

User Code - Programming 8

Master Code - Programming 9

Other Features

Keypad panic 9

Keypad Duress 9

Test Functions 10

Warranty 11

Section List 12

Important Information 13

Contents

page 1

Terms .....you may need to know

Alarm - The state of a security system when an armed sensor has been

activated.

Arming - To place a section or panel ready to accept an alarm.

Central - A place where alarms are received and appropriate action

Station taken in response to the Station alarm.

Door - A sensor which detects the opening of a door.

Contact

EntryTimer- A timer that is used to delay the activation of an alarm

Exit Timer - A timer used to delay the arming of an Exit / Entry section.

Handover - A section that has Exit delay but only has Entry delay

Section when an Exit and Entry Section has been activated ﬁrst.

Isolate - To inhibit or bypass one or more sections from arming.

Microwave - A detector which detects movement by the use of microwave

Detector energy.

Partial - Only part of the security system is Armed.

(Pre Programmed sections are isolated).

PIR (Passive- A detector which detects movement by sensing sudden

Infra Red) changes in Infra Red temperature.(e.g. Body Heat)

Plug Pack - A transformer which converts the 240 VAC Mains Power to

16 VAC to run the Security System.

Sealed - When a section is Armed and has not been activated.

Silent - A section may be programmed to be silent. i.e. does not trigger

the siren or strobe when alarmed.

Siren Timer- A timer used to limit the running time of the siren.

System OFF- Security System is disarmed for all sections that are not

programmed for 24 Hour.....Note: Fire, Panic and Tamper,

if available, are still Armed.

System ON- Security System is Armed for all sections that are not isolated.

page 2

Keypad - Indicators

Section Lights- There are 8 or 24 section lights on the command centre.

- When the system is in the OFF mode all non 24 hour

sections are not armed and the Section Lights indicate

the condition of the sensor..When the Section Light is

On the sensor is activated (e.g. door contact detecting

door open or motion detector sensing movement).

When the Section Light is OFF the sensor is not activated.

- When the system is in the ON mode all non isolated sections

are armed. If the section light is FLASHING the sensor is

activated and triggers the siren and strobe light (if it is not

silent).This alarm is transmitted to the central station. When

the light is out the section is not activated.

- When the system has been Armed, an exit timer starts and

holds the sections that have been programmed for Exit or

Entry delay disarmed. This allows the user to exit the

premises without activating the alarm.

- When the system is armed, and the Exit timer has ﬁnished,

Entry into the premises can be made via a section that has

Entry delay. This starts the Entrydelay and if the system is

disarmed there will be no alarm.

Power Light - This light is normally ON. This indicates that the Plug Pack

power and backup battery are normal.

- When the Plug Pack power is not good (i.e. the mains has

failed) the power light will single ﬂash.

- When the Plug Pack power and battery are not good, the

power light will double ﬂash.

Program Light - Flashing while in Program mode. Program mode is entered

when a user code is entered and isolate or test modes are

selected. Program mode is also selected when the master

code is entered and the user codes are being viewed or

changed.

- When not in program mode the Program Light is Off

page 3

Keypad - Indicators .....cont'd

*LED keypads only

Partial Light - ON when the Partial mode has been selected and only

some of the sections are armed.

- Single ﬂash when the system is Partially armed and Exit

timer is running.

- Double ﬂash when the system is armed and the Entry

timer is running. The Entry timer is started when an

Exit / Entry is activated.

- OFF indicates partial mode is not selected.

On Light - Off when the system is Off

- Single ﬂash when the system is armed and Exit timer is

running.

- Double ﬂash when the system is armed and the Entry

timer is running. The Entry timer is started when an

Exit / Entry is activated.

Fire Light * - If the phone line has failed or is not connected, the Fire

Light will double ﬂash. Once the line has restored

the Fire light will remain on for a further12 seconds

before turning off

Auxillary Light * - The Auxillary Light is used to indicate the state of the

Tamper input. When the tamper input is triggered, the

AUX light will double ﬂash. If the tamper is

acknowledged by disarming the system while the

tamper is still open the AUX light will become solid.

Once the tamper switch has sealed the AUX light will

turn off. If the tamper has already sealed once its

been acknowledged, the AUX will light will simply turn off

page 4

Keypad Keys

0 - 9 Keys - Used to enter numeric Codes or Function Numbers.

Test Key - Used when a valid User Code has been entered to

enter Test mode.

Isolate Key - Used when a valid User Code has been entered to

Isolate a section, usually before Arming the System.

Partial Key - Used when a valid User Code has been entered to Arm

the System with Pre Programmed sections Isolated.

Off Key - Used when a valid User Code has been entered to

Disarm the System.

On Key - Used when a valid User Code has been entered to Arm

the System, it is also used as the code key when in

programming mode.

NOTE : Some keypads have a seperate code button to

access program mode.

page 5

page 6

Fully Arming the System - ON Mode

Notes:

1. The system will not change to ON mode unless all section lights are

out or isolated.

2. Power light should be ON and not ﬂashing.

3. Program, Fire and Auxillary lights,if ﬁtted, should be out.

4. Exit Timer starts as soon as ON light starts ﬂashing and beeper gives

an exit warning.

5. Exit via programmed Exit/Entry sections only.

6. If the Exit / Entry sections are not sealed by the time the exit timer

expires then the siren and strobe will give 2 seconds warning and

the entry timer is started. If the system is not turned to OFF mode

before the entry time expires a full siren / strobe and alarm

transmission to the Central Station occurs.

Key Sequence Operation

Example shows a User Code 1 2 3 4

1 2 3 4 on being used to change the system to

ON mode

Partially Arming the System - Partial Mode

Notes:

1. Only part of the system will be armed. Actual sections being

armed depends on setup by technician during installation.

2. The section lights of the sections which are being armed in Partial

mode must be out otherwise the system will not change to Partial

ON mode.

3. Check Power light is on and not ﬂashing.

4. Program, Fire and Auxillary, if ﬁtted, lights should be out.

5. Exit Timer starts as soon as Partial light starts ﬂashing and beeper

gives exit warning.

6. Exit via programmed Exit/Entry sections only.

7. If the Exit / Entry sections are not sealed by the time the exit timer

expires then the siren and strobe will give 2 seconds warning and

the entry timer is started. If the system is not turned to OFF mode

before the entry time expires a full siren / strobe and alarm

transmission to the Central Station occurs.

Key Sequence Operation

Example shows a User Code 1 2 3 4

1 2 3 4 part being used to change the system to

Partial ON mode

page 7

Isolate a Section from being Armed

Notes:

1. When entering section numbers a two digit number eg 01 or a single 1

may be used. Single digit entry. i.e. the leading zero is ignored)

2. Only valid section numbers may be entered.

3. Sections are automatically de-isolated when the system is changed to

OFF mode.

4. Depending on technician setup, isolations may be reported to the

Central station.

Key Sequence Operation

Example shows a User Code 1 2 3 4

1 2 3 4 isolate being used to enter Isolation mode.

0 4 Sections 4 and 7 are being Isolated.

0 7

ON or part When desired sections are isolated

Disarming the System - OFF Mode

Notes:

1. Only a valid User Code can change the system between OFF, ON and

Partial modes.

2. Fire, Panic and Tamper inputs, if ﬁtted, are always armed.

3. This key sequence also acknowledges or silences the siren / strobe if a

Fire, Panic or tamper alarm is actuated.

Key Sequence Operation

Example shows a User Code 1 2 3 4

1 2 3 4 Off being used to change the system to

OFF mode

page 8

Changing User Codes

1. User 01 default is 1111.

2. User codes are 4 digits long. (The Master Code is 6 digits long)

3. User codes are used to change the status of the panel, isolate sections,

test or acknowledge alarms.

4. User codes cannot be the same or within one count of another User code

including the ﬁrst 4 digits of the Master Code.

5. To change User codes the system must be in the OFF mode.

Key Sequence Operation

Example shows a Master

code eg 218572 used to

2 1 8 5 7 2 On enter program mode.

(Enter your own)

0 1 Select User code 01

1 2 3 4 On Enter new code 1 2 3 4

0 7 Select User code 07

8 7 6 5 On Enter new code 8 7 6 5

Off Exit program mode

with the OFF key.

The keypad panic may be initiated by holding both the ON and

the OFF keys depressed together for a period of 3 seconds. If

the alarm system is monitored a panic alarm report will be sent

to the monitoring station and, if enabled by the installer, the

sirens will sound.

Sirens enabled for Panic YES NO

Keypad duress must be enabled by the installer at installation.

The and is initiated by incrementing the last digit of a valid

user code by 1. For example, if the users code was 1234, then

a duress signal would be sent to the monitoring station if the

user entered 1235 as their code. In all other respects the panel

would react as if the normal code had been entered. For user

codes ending in 9 then a 0 would be entered eg. normal code is

1949, duress code would be 1940.

Keypad duress enabled YES NO

page 9

Changing the Master Code

Notes:

1. Master code default is 218572.

2. Master code is 6 digits long.

3. The Master code is only used to program the user codes. It cannot

change the status of the system. (Arm or disarm the panel)

4. The system must be in OFF mode to enter the master code.

Key Sequence Operation

Enter existing Master

2 1 8 5 7 2 ON code 218572 used to

enter program mode.

0 0 Select function 00

2 4 6 8 1 2 ON Enter new master

Code e.g. 2 4 6 8 1 2

Off Exit program mode

with the OFF key.

Other Features

Keypad

Panic

Keypad

Duress

Indice

Altri manuali MCM Electronics Pannello di controllo

MCM Electronics

MCM Electronics iRIS8+ Guida utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche

MCM Electronics iRIS 8 Manuale utente

Manuali Pannello di controllo popolari di altre marche