Meanwell LCM-25 Manuale utente

Wiring

Environmental limitations

Cautions

Settings and connections

1. Output Current Level Settings

Features

‧180~277VAC input only

‧Built-in active PFC

‧Output current level selectable by DIP switch

‧Built-in 0~10Vdc and PWM signal dimming function

Power supply synchronization function up to 10 units‧

‧ⅡClass power unit, ungrounded

‧Full plastic case enclosed

‧No load power consumption <0.5W

‧Protections: Short circuit / Over temperature

‧3 year warranty

Suitable for intelligent LED lighting‧

‧Housing with cable clamp for remote installation

‧Use wires with an adequate cross-section (see 4)

‧Use suitable mounting tools to do the wiring and mounting (see 4)

‧Use a (miniature MCB circuit breaker) with an adequate current rating to protect the lighting system (see 6)

‧℃Maximum ambient temperature must not exceed 60

‧Always allow adequate ventilation clearances, 50mm, around the unit in use to prevent it from overheating

‧Only install the unit in interior environments

‧This unit must be installed by a qualified electrician

‧It's not suitable to connect DC/DC constant current drivers as the output loads

The LCM can provide various output currents by setting the DIP switch. The settings of the DIP switch are shown in the tables below.

LCM-25

Note : 1.Factory default setting is 700mA.

2.Output voltage and output wattage must not exceed the rated values.

Voltage

range 1 2 3 4 5 6

Selectable

Current

6-54V --- --- --- --- -- - - - -

--- --- --- --- -- -

--- ---

---

ON ON

ON ON ON ON

ON ON ON ON ON

ON ON ON ON ON ON

350mA

6-50V 500mA

6-42V 600mA

6-36V 700mA*

6-28V 900mA

6-24V 1050mA

LCM-25 installation manual

Terminal blocks assignment for LCM

2. Connection of LED Lamps

Press down the "push button" by a slotted screw driver to insert or remove the cable.

Vo-

Vo+

AC/N

AC/L

NEUTRAL (Blue or white)

LIVE (Brown or black)

http://www.meanwell.com



  



SYN.

AC/N

AC/L

105mm

68mm

23mm

+Vo

-Vo

DIM-

DIM+

+ +

- -

3. Connection of Dimming Functions

a. 0~10Vdc or 10V PWM

b. Synchronization operation

http://www.meanwell.com

DIM-

DIM+ 0~10Vdc or 10V PWM

4. Recommended Screwdriver, Wire and Torque Setting

5. Suggested Maximum Number of the LCM Units that can be Connected to a MCB ( circuit breaker) at 230Vac miniature

Note: These calculated values are based on MCB S201 series manufactured by ABB.

Type

Model B10 B16 C10 C16

LCM-25 20 32 34 54

Solid wire

Stranded wire

American wire gauge

Wire stripping length

Screwdriver

Recommended tightening torque

Suggested push-down strength

-----

6mm Philips

4kgf-cm (3.47 lb-in)

Clamp connector Push terminal

(ACL/N)

Ј0.8 -Ј1.8mm

0.5 - 2.5mm

14 - 20AWG

10mm (0.39")

3mm Slotted

-----

3 - 4 kp (6.61-8.81 lbF)

Ј0.8 -Ј1.382mm

0.5 - 1.5mm

16 - 20AWG

7mm (0.27")

3mm Slotted

-----

1.5 - 2.4 kp (3.31-5.29 lbF)

Push terminal

(Vo , DIM )± ±

+Vo -Vo DIM- DIM+

LCM-25

(Master)

LCM-25

(Slave 4)

LCM-25

(Slave 1)

LCM-25

(Slave 5)

LCM-25

(Slave 9)

SYN. SYN.SYN. SYN. SYN.

CN101

CN100

5m 5m

-- ---

.....

.. .

‧Synchronization up to 10 drivers (1 master + 9 slaves)

Dimming operating range : 10%~100%‧

‧Sync cable length : < 5m

‧Sync cable type : Flat cable

‧Sync cable cross section area : 22 – 24 AWG (0.2~0.3mm )

‧Cn100, CN101 : used to synchronously control the LCM

units in parallel.

NOTE: 1. Please make sure all units are set to 100% dimming setting (factory default) before synchronizing.

2. Min. Dimming operating range depends on dimmer setting.

Altri manuali Meanwell Alimentazione elettrica

Meanwell

Meanwell LPHC-18 Manuale utente

Meanwell

Meanwell RSP-1000 Series Manuale utente

Meanwell

Meanwell AP Manuale utente

Meanwell

Meanwell PWR-40-24 Manuale utente

Meanwell

Meanwell LAD Series Manuale utente

Meanwell

Meanwell LCM-40(DA) Manuale utente

Meanwell

Meanwell DDR-120A-12 Manuale utente

Meanwell

Meanwell SHP-10K-HV Series Manuale utente

Meanwell

Meanwell KNX-20E-640 Manuale utente

Meanwell

Meanwell HDR-15 Series Manuale utente

Meanwell

Meanwell DRDN20 Manuale utente

Meanwell

Meanwell DDR-120 Series Manuale utente

Meanwell

Meanwell DR-RDN20 Manuale utente

Meanwell

Meanwell HEP-1000 Manuale utente

Meanwell

Meanwell DRS Series Manuale utente

Meanwell

Meanwell HEP-1000 Manuale utente

Meanwell

Meanwell NDR-75-12 Manuale utente

Meanwell

Meanwell PHP-3500 Manuale utente

Meanwell

Meanwell TDR-960 Series Manuale utente

Meanwell

Meanwell DRP-3200 Series Manuale utente

Meanwell

Meanwell RST-7K5-HV Series Manuale utente

Meanwell

Meanwell RSP-2400-12 Manuale utente

Meanwell

Meanwell RHP-1U Series Manuale utente

Meanwell

Meanwell KNX-40E-1280D Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente