Mec CAD-E0930 PR1D Manuale utente

Page: 1/16

User Manual

CAD-E0930 PR1D

Portable Air-conditioner

Contents

Important Safeguards.............………………………………………….…….…... 3

Function Description……………….……………………………….…………...…. 5

Features and Parts…………………………………………………….…………….5

Installation…………………………………………………..…………………. …….6

Control Setting…………………………………………………………….………….9

Remote Conrtol ………………………………………………………………… 11

Water Drainage Methods………..…………………………………………………12

Maintenance…………………………………..………………….………….………13

End of Season Storage………………..……………………………………………15

Handling of the Unit……………………………………………………………….…15

Troubleshooting……………………….………………………………………….…16

Appendix………………………….……………………………………….…….……16

Page:2/16

Page: 3/16

Thank you for selecting this super quality air-conditioner. Please keep this User’s Manual

properly for future reference. Read the User’s Manual carefully before operating this unit.

Important Safeguards

Important safeguards:

* This air-conditioner is suitable for indoor use only rather than for other occasions.

* Rated operating range: this unit shall be connected to 220 -240V/50Hz power output end.

* The air-conditioner shall be installed in accordance with the wiring rules of local grid to

ensure proper grounding. Should you have any question about electrical installation, follow

the User’s Manual or have the installation done by professional electrician whenever

necessary.

* Please put this unit in a flat and dry place and keep it at least 50cm away from surrounding

objects or walls.

* Once the air-conditioner is installed, ensure that the plug wire is in good condition and

inserted firmly into the power socket and always ensure that the power cord is arranged in

order to prevent the personnel from stumbling over it or the plug from being pulled out.

* Do not insert any object into the air inlet/outlet of the air-conditioner. Be sure to keep the air

inlet/outlet of the air-conditioner unblocked.

* Where there is the need to install a drain pipe, ensure that the connection of the drain pipe is

in good condition without flexure.

* When adjusting the horizontal/vertical louver at the air outlet, turn it slightly by hand to avoid

damage of the louvre.

* Keep the unit in an upright position when moving it.

* Keep this unit away from gasoline, flammable gases, oven or other heat sources.

* Do not dismantle, inspect or modify the unit without authorization as this may result in fault

of the unit, and even bodily injury & property damage; to avoid dangers, if the unit is faulty,

be sure to have it repaired by the manufacturer or professionals.

* Do not install and operate this air-conditioner in a bathroom or other wet environments.

* Do not allow the children to play with this machine. Closely supervise the children or

disabled people when this unit is in use.

* Do not turn off this unit by removing the plug.

* Do not place such objects as cups on the unit to prevent water or other liquids from spilling

into the air-conditioner.

* Do not use pest control aerosol or other flammable substances near the air-conditioner.

* Do not wipe or wash the air-conditioner with chemical solvents such as gasolines and

alcohols, etc. Before cleaning the air-conditioner, be sure to turn off the power supply and

wipe it with soft semi-wet cloth; if the machine is indeed very dirty, wipe it with neutral

cleaner.

Recommendation:

Do not operate this unit if the ambient temperature is greater than 35℃in the cooling mode

or lower than 5℃in the heating mode.

Function Description

This series of mobile air-conditioners are available in cooling only and cooling &

heating models of different sizes. The cooling only models offer the cooling, dry, air

blowing and sleep functions; the cooling & heating models offer the cooling, dry, air

blowing and heating functions. The speed of the fan is adjustable between high fan speed

and low fan speed, the temperature setting range is 17-300C, and various protection

functions such as (24h) timed ON/OFF setting.

Features and Parts

1. Features

·Brand new appearance, compact structure with a sense of streamline.

··The appearance of the unit is beautiful and elegant; the remote control can be placed on the

right of the handle at the back of the unit, and the remote control features user-friendly

memory design.

··The structure of the power cord at the back and the universal jack design can better protect

the power cord.

·The position of the outdoor connector is high to allow for convenient assembly and smooth

air flow of the heat exhaust hose.

·Timed start/shutdown function, unique start/shutdown music.

·3-minute delay compressor restart protection function, multiple other protection functions.

·The free snap-fit design of the heat exhaust hose allows for more convenient installation of

the unit.

Page:4/16

2. Parts:

1. Control panel 14. Lower air duct bottom

2. Horizontal louvre 15. Wire-winding post

3. Vertical louvre 16. Drain cap

4. Air outlet frame 17. Evaporator filter mesh

5. Vertical Louvre connecting lever 18. Evaporator filter frame

6. Caster 19. Radiating fine mesh

7. Horizontal louvre connecting lever 20. Condenser filter mesh

8. Main vertical louver 21. Condenser filter frame

9. Front shell 22. Base plate

10. Handle position (right side: remote

control storage area)

11. Back shell

12. C shape bucke of the heat

exhaust hose snap

13. Power cord

Installation Adjustment

1. Installation

Page:5/16

Page: 6/16

Warning: leave this mobile air-conditioner in an upright position for at least 2

hours before first use.

This air-conditioner may be moved indoor conveniently; leave the air-conditioner in an

upright position while moving it. The air-conditioner shall be placed on a flat ground surface.

Do not install or operate this air-conditioner in a bathroom or other wet environments.

1.1 .Installation of the C shape buckle of the heat exhaust hose and unit

Figure 1 Figure 2

1). Take out the C shape buckle of the heat exhaust hose and remove the plastic bag.

2). Point the rotary hole at the end of the heat exhaust hose snap toward the rotation shaft

of the back shell and slide it onto the back shell in accordance with the snap joint

direction of the rotation shaft on the back shell (as shown in Figure 1).

Note: 1. When the end snap joint at the end of the rotation shaft of the back shell sticks

out of the snap, it means that the heat exhaust hose snap has been slided into

place.

3). Rotate the C shape buckle of the heat exhaust hose that is slided into place

counterclockwise to clip the snap joint of the C shape buckle of the back shell

successfully through the guide of the slide way of the back shell (as shown in Figure 2).

Note: 1. Do not rotate the C shape buckle of the heat exhaust hose if it is not slided into

place as this may damage the rotation shaft of the back shell and the C shape buckle of

the heat exhaust hose.

1.2 Installation of the heat exhaust hose assembly and unit

1). Pull the end of the heat exhaust hose apart by several turns;

2). Hold the end handle of the C shape buckle of the heat exhaust hose with the left hand

and the heat exhaust hose short connector with the right hand, put one end of the heat

exhaust hose that is pulled apart onto the snap of the lower air duct bottom, press the

C shape buckle of the heat exhaust hose with the left hand by force so that the C

shape buckle of the heat exhaust hose clips the snap joint of the back shell (as shown

in Figure 3).

Note: 1.The end of the heat exhaust hose must reach one step inside the bottom of the

lower air duct (as shown in Figure 4).

2.The few turns at the end of the heat exhaust hose must be snapped in the

snap of the lower air duct bottom.

Rotary hole

Rotation shaft of the

back shell

Slide way of the back

shell

Snap joint of the C

shape buckle of the

ack shell l

Page: 7/16

3.The C shape buckle that clips the heat exhaust hose must clip the back shell

and heat exhaust hose firmly.

Figure 3

Figure 4

3). Hold the unit with one hand and the heat exhaust hose short connector with another

hand; or both people cooperate with one person holding the unit and the other person

pulling the heat exhaust hose to prolong the heat exhaust hose gently.

Note: 1. Do not separate the heat exhaust hose assembly from the unit.

2. Do not tilt the unit when pulling apart the heat exhaust hose.

1.3 Installation of the window sealing board assembly

2). Half open the window and mount the window sealing board assembly onto the window,

either vertically or horizontally (as shown in Figure 5 and 6).

3). Pull apart the parts of the window sealing board assembly, adjust the distance of the

window sealing board assembly pulled apart so that the two ends of the assembly

come into contact with the window frame, and fasten the parts of the assembly with

copper screws.

Figure 5 Figure 6

1.4 Installation of the unit

1). Move the machine with the heat exhaust hose assembly installed before the window

and keep the unit at least 50cm away from the walls or other objects. (As shown in

Lower air duct

bottom joint

Position of

lower air duct

bottom step

Figure 7).

2). Snap the flat end of the heat exhaust hose short connector into the elliptical hole of

the window sealing board assembly (as shown in Figure 8 and 9).

Note: 1. The flat end of the heat exhaust hose short connector must be snapped into

place.

2. The heat exhaust hose may not be bent and shall be free from significant

(greater than 45°) flexure, and the heat exhaust hose shall be ventilated properly.

Figure 8 Figure 9

Important notes:

The exhaust hose is 280mm-1500mm long and this length is determined based on the

specification of the air-conditioner (s). Do not use prolonged hose or replace with other

different hoses as this may affect the functions of the air-conditioner. The exhaust must be

smooth and the air-conditioner may overheat if the exhaust is obstructed.

Control Setting

Page:8/16

REMOTE CONTROL

Buttons of the remote control operating instructions as below:

1) High Press this button to select high fan speed(except Dry mode and sleep

mode)

2) Low Press this button to select low fan speed.

3)Sleep Press this button to select sleep mode

4) Timer When turn off the unit, press this button to set the time of turn

on;when turn on the unit, press this button to set the time of turn off

5) Up Press Up or Down button to set temperature or adjust the time in Timer

mode.

6)Down Press Up or Down button to set temperature or adjust the time in Timer

mode.

7) CoolPress this button to choose Cool mode.

Page:9/16

8) Dry Press this button to choose Dry mode

9) Fan Press this button to choose Fan mode.

10) Vary from Celsius degree to Fahrenheit degree.

11) PowerPress this button to turn on/off the unit.

Water Drainage

1. Manual drain: (as shown in Figure 10)

1). Once the unit shuts down upon full water, turn off the power of the unit and then unplug

the power plug.

Note: move the unit carefully to avoid spillage of water in the water tray at the bottom

of the unit.

2). Put the vessel that holds water below the water outlet at the back of the unit.

3). Screw off the drain cap, unplug the water plug and water will flow into the vessel that

holds water automatically.

Note: 1. Protect the drain cap and water plug properly.

2. Tilt the unit slightly backward when draining.

Page:10/16

Indice

Altri manuali Mec Condizionatore d'aria

Mec

Mec iPort G12000 PR1C 1.5HP Manuale di manutenzione

Manuali Condizionatore d'aria popolari di altre marche

Spheros

Spheros CC 355 Manuale utente

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuale utente

Panasonic

Panasonic CS-E12HKEW Manuale utente

nedis

nedis ACMB1WT7 Manuale utente

Samsung

Samsung AR KV Series Guida

Daikin

Daikin FCFV50A Manuale utente

Fujitsu

Fujitsu Inverter ASBA30JFC Manuale utente

Toshiba

Toshiba RAS-M10SMUV-E Manuale utente

Daikin

Daikin FXLQ20MAVE Manuale utente

Hitachi

Hitachi RAS-E24CAK Manuale utente

CIAT

CIAT Magister 2 Series Guida

Bestron

Bestron AAC6000 Manuale utente

Hisense

Hisense 7K Manuale tecnico

Frigidaire

Frigidaire FFRE0533S1E0 Manuale utente

Samsung

Samsung AS09HM3N Manuale utente

Frigidaire

Frigidaire CRA073PU11 Manuale del proprietario

Soleus Air

Soleus Air GB-PAC-08E4 Manuale utente

McQuay

McQuay MCK020A Manuale utente