Mega LED Lighting MJ-1014 Manuale utente

LED SPOT 90

MJ-1014

User manual

Thank you for choosing our 90W LED moving head light. For the sake of your safety, Please

read and follow these instructions carefully and keep this manual in a safe place for future

reference.

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

Catalogue

Chapter Page

Safe Usage Of The Product -----------------------------------------------------------------------------------------3

Install The Equipment ------------------------------------------------------------------------------------------------4

Power Code Connection ---------------------------------------------------------------------------------------------4

DMX Connection ------------------------------------------------------------------------------------------------------5

DMX Terminator -------------------------------------------------------------------------------------------------------6

Function Set---------------------------------------------------------------------------------------------------------------6

Operation Menu ---------------------------------------------------------------------------------------------------------6

Maintenance --------------------------------------------------------------------------------------------------------------8

Keeping The Product Clean ------------------------------------------------------------------------------------------9

Trouble Shooting---------------------------------------------------------------------------------------------------------9

Equipment and Appendix----------------------------------------------------------------------------------------------9

Channel List---------------------------------------------------------------------------------------------------------------9

Technical Parameters---------------------------------------------------------------------------------------------------11

☆Important notice:

·In this instruction for use contains about the installment and the use aspect important information of the LED moving

head. When installing and using, you need to look this usage instruction strictly.

·Before open the LED moving head and if you want to do the repair work, please make sure the power source is at the

separation condition.

·Every unit is tested completely and packed properly by themanufacturer. Pleasemake sure the packing and the unit are

in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer

and do not use the unit. Any damage caused by improper use will not be assumed by themanufacturer or dealer.

Attention: Unceasingly carries on the product improvement about our company the policy, in this instruction booklet

carries the data will have the possibility to be able to change in the future, when no longer separate notice change matters

concerned. Our company retains when the product improvement changes the related specification the authority. This

instruction booklet publisher cannot be responsible regarding this instruction booklet in information accuracy, also cannot

the related consequence which causes regarding these information be responsible.

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

SAFE USAGE OF THE PRODUCT

When unpacking and before disposing of the carton, check there is no transportation damage before

using the product. Should there be any damage caused by transportation, consult your dealer and do

not use the apparatus.

The product is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain

and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other

liquids.

The product is not designed or intended to be mounted directly on to inflammable surfaces

The product is only intended for installation, operation and maintenance by professional person.

The product must be installed in a location with adequate ventilation, at least 50cm from adjacent

wall surfaces. Be sure that no ventilation slots are blocked.

Do not product the beam onto inflammable surfaces, minimum distance is m.

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the

power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull

out the plug by tugging the power-cord.

Keep the optical system clean. Do not touch the lens with bare hands.

The product should always be installed with a secondary safety fixing. On the projector base brink,

there is a hole for the safety cord provided. It should be attached as shown in “installing the

projector” section.

The lens shall be changed if they have become visibly damaged to such an extent that their

effectiveness is impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 40°C，when steady state is

achieved 50°C.

There is no user serviceable parts inside the projector, do not open the housing and never operate the

product with the covers removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

★Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

Install The Equipment:

Use 2pcs clamp and 1safety cord(need to purchase).Use clamp fix with light hook which in the

packing box with light, then use screw install to the bottom of lamp. Hang the fixture on the structure

and fasten the screws attached to each clamp. Make sure the light is installed reliable, and confirm

the light which you fixed is strong enough for hanging the light. Base on safety reason, please

according to the above picture using safety wire cross the light to make it strong enough again.

Warning!

1．Light Hook and clamp only use for hanging the light. Do not use clamp as a tool to move fixtures.

2．Base on safety reason, please use the safety cord which can afford the weight ten times of lamp

through Insurance hole for auxiliary hanging.

3．Don't use the handle of the moving head light to fixed or lift!

Power Code Connection:

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and

frequency marked on the panel of the projector. It is recommended that each projector be supplied

separately so that they may be individually switched on and off.

★It is essential that each projector is correctly earthed and the electrical installation conforms

to all relevant standards.

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

DMX Connection:

Connection between the controller and a projector and between one projector and another must be

made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to

and from the projector is via cannon 3 pin (which are included with the projector) XLR plugs and

sockets. The XLR's are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each

other. The body of the plug is not connected in any way. The XLED 590 accepts digital control

signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the

second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last

fixture’s output to a DMX terminator as shown in the figure below.

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

DMX Terminator:

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a

DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control

signals.

The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins

2 and 3, which is then plugged into the output socket on the last projector in the chain. The

connections are illustrated below.

Function Set:

MENU DOWN UP ENTER

Use button switch and LCD display, can set the address code and function code easily.

Check or modifylighting functionsettings, Pressthe MENU or ENTERbutton. LCD displaypanelwill

displaymain menus. Functionoperation menu all have corresponding submenu . Eachmenu allrepresent the

specific functionsoflamps, specific see below "operation menu"section.

Setorbrowsefunctionsettingoflamp, PressUP orDOWN key.

Press ENTER key to save your changes or to ENTER submenu, Press UP or DOWN can change

value(Plus or reduce number).

Operation Menu:

Menu Structure chart

Main Menu Sub Menu

DMX Address Set(001-512)

Address

LCD Display

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

…… ……

Sub menu include address, Option, Display, Man Control , Test operation, Resume default,and Fixture

reset..

Address setting,

1. Press “Menu” button to Set DMX Address，to confirm by press “ENTER” button。

2. Show Set DMX address DMX address:001，correct by pressing “UP&DOWN” button。

3. Press “ENTER” button to save and quit. Press “MENU” button to quit no saving

Option

Press “Menu” , and choose Option by “UP&DOWN”，it will be show X Reverse , Y Reverse,

XY Exchange three mode, to confirm by press “ENTER” button.

1. X Reverse Settings, Choose menu by pressing ”UP&DWON” button, will show YES/NO,.

correcting by “ENTER” Button..

Option

X Reverse

Y Reverse

Display

XY Exchange

Language

Poorlight

Display LOGO

Man Control

CH1

CH2

CH3

CH18

Sound

Test operation

Auto

Program run

Resume default

Fixture reset

Lighteness

Yes/No

Chinese

English

1-32

Constant open

Dim

Off

ON/OFF

0－255

Yes/No

Enter

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

2. Y Reverse Settings, Choose menu by pressing ”UP&DWON” button, will show YES/NO,.

correcting by “ENTER” Button..

3. XY Exchange Settings, Choose menu by pressing ”UP&DWON” button, will show YES/NO,.

correcting by “ENTER” Button..

Display

Press “Menu” , and choose Display by “UP&DOWN”，it will be show Language,Lighteness,

Poorlight three mode, to confirm by press “ENTER” button.

1. Language Settings, Choose menu by pressing ”UP&DWON” button, will show Chinese/English,.

correcting by “ENTER” Button.

2. Lighteness Settings, Choose menu by pressing ”UP&DWON” button, will show 1 to 32,.

correcting by “ENTER” Button.

3. XY Exchange Settings, Choose menu by pressing ”UP&DWON” button, will show Constant

open, Dim, Off. correcting by “ENTER” Button.

Man Control

Press “Menu” , and choose Man control by “UP&DOWN”，it will be show CH1 to CH16, to

confirm by press “ENTER” button.

1. CH1 . Press the ENTER then pressing ”UP&DWON” button, will show 001 to 255,.

correcting by “ENTER” Button.

2. CH2 . Press the ENTER then pressing ”UP&DWON” button, will show 001 to 255,.

correcting by “ENTER” Button.

…………………………

3. CH18 . Press the ENTER then pressing ”UP&DWON” button, will show 001 to 255,.

correcting by “ENTER” Button.

Test operation

Press “Menu” , and choose Test operation by “UP&DOWN”，it will be show Sound or Auto

mode, to confirm by press “ENTER” button.

Resume default

1. Press “Menu” and choose Resume default by “UP&DOWN”，confirm by press “ENTER” button,

it shows factory settings

Fixture rese

Press “Menu” and choose Fixture rese by “UP&DOWN”，confirm by press “ENTER” button, it

shows reset.

Maintenance:

To prolong the life of the projector, some maintenance work has to be done to ensure the LED

optical system in good condition. If the projector does not function, check the fuses on the power

socket of the projector, they should only be replaced by fuses of the same specification. Should

these be damaged, call a qualified technician before replacement. The projector has thermal

protection device that will switch off the projector in case of overheating. Should either of these

operate, check that the fans are not blocked, and if they are dirty, clean them before switching on the

projector again. Check that the fans are operational, if not, call a qualified technician.

☆Any maintenance work should only be carried out by qualified technicians.

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

Keeping The Product Clean:

To ensure the reliability of the projector, it should be kept clean. It is recommended that the fans

should be cleaned every 15 days. LED lens should also be regularly cleaned to maintain an optimum

light output.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or

particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics. A soft cloth

and typical glass cleaning products should be used for cleaning. It is recommended to clean the

external optics at least once every 15 days.

☆Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

Trouble Shooting:

Problem

Answer

The LED moving head light doesn’t switch

on.

Check the fuse the power socket

Although shines, but the LED moving head

lamp doesn’t accept the instruction of the

controller.

Check the digital start address and

also check the connection situation of

the communication control line

LED moving head lamp only can work

intermittently.

Inspect the power supply and voltage

is whether normal.

Do not receive the DMX512 signal.

Whether the signal lines do contact

well or broken.

The light beam appears gloomily.

Check that the heat dissipation

system is running normally or Inspect

the optics part is whether clean.

☆Other maintain work should by the specialist which has the experience to carry on.

Equipment and Appendix:

The packing list of this light as follows:

☆Led moving head light 1pcs

☆XLR connector 1unit

☆Light Hook 2pcs

☆M8 Screw 4pcs

☆The Product of Instruction 1pcs

Channel List:(18CH)

Channel

Function

Value

Function Description

CH1

Dimmer

0-255

Dimmer 0-100%

CH2

Strobe

0-240

Strobe from slowly to quickly

241-255

Light ON

LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0

www.mjledlighting.com

CH3

Color

0~15

White

16~31

Red

32~47

Green

48~63

Yellow

64~79

Blue

80~95

Pink

96~111

Cyan

112~126

Orange

127~190

Rainbow effect(Fast~slow)

191~255

Rainbow effect(slow~Fast)

CH4

Color half step

0~255

Color half step

CH5

Pan

0~255

Pan movement

CH6

Tilt

0~255

Tilt movement

CH7

prism

0~255

prism

CH8

Prism Rotation

0~255

Prism Rotation

CH9

Gobo1

0~15

White

16~31

Gobo 1

32~47

Gobo 2

48~63

Gobo 3

64~79

Gobo 4

80~95

Gobo 5

96~111

Gobo 6

112~127

Gobo 7

128~190

Rainbow effect (Fast ~slow)

191~255

Rainbow effect (slow~Fast)

CH10

Gobo1 Rotation

0~255

Gobo Rotation

CH11

Gobo1 half step

0-255

Gobo Half Step

CH12

Gobo2

0~12

White

13~25

Gobo 1

26~38

Gobo 2

39~51

Gobo 3

52~64

Gobo 4

65~77

Gobo 5

78~90

Gobo 6

91~103

Gobo 7

104~116

Gobo 8

117~127

Gobo 9

128~191

Rainbow effect (Fast ~slow)

192~255

Rainbow effect (slow~Fast)

CH13

Iris

0~255

Iris

CH14

Focus

0~255

Focus

CH15

Pan Fine

0~255

Pan Fine

Indice

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente