Megamaster SRPH09 Guida di riferimento rapido

LPGSASA Permit Number: 1185-34/1-RSA-12-A

ASSEMBLY & OPERATING INSTRUCTIONS

Important: Read these instructions for use carefully so as to familiarize yourself with the

appliance before connecting it to its gas container. Keep these instructions for future reference

Patio Heater

Powder Coated / Stainless Steel

Product may differ slightly from pictures within this

manual

!WARNING

•For Outdoor Use Only

•Read the instruction before installation and use.

•Keep the instructions for future references.

WARNING

•Do not store use gasoline or other flammable vapors and liquids in

the vicinity of any other appliance.

•An LP cylinder not connected for use shall not be stored in the

vicinity of this or any other appliance.

WARNING

•Turn off the gas valve immediately if smell of gas is detected.

•Extinguish any open flame.

•If odour continues, contact your gas supplier immediately.

WARNING

•The user assumes all risk in the assembly and operation of the gas

heater. Failure to follow the warnings and instructions in this

manual can result in severe personal injury, death or property

damage.

•If user cannot read or fully understand the instruction manual,

please contact your dealer. Manufacturer or supplier will not be

responsible for user’s negligence.

TABLE OF CONTENTS

Caution…………………………………………………………………………….4

Heater Stand and Location…………………………………………………….6

Gas Requirements………………………………………………………………6

Leakage Test……………………………………………………………………..7

Fuel Gas Odour………………………………………………………………….7

Pre-Operation Check...…………………………………………………………8

Lighting Instructions…………………………………………………………...9

Flame Characteristics…………………………………………………………10

Storage…………………………………………………………………………...10

Cleaning and Maintenance…………………………………………………...10

Burn Back………………………………………………………………………..11

Assembly Instructions………………………………………………………...12

Parts and Hardware………………………...................................................13

Problems Check List…………………………………………………………..18

Service and Maintenance Information…………………………………….. 18

Technical Information………………………………………………………....19

Warranty………………………………………………………………………….20

CAUTION

PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE

OPERATION

•Do not make any unnecessary adjustments or modifications to this grill, a

qualified LP gas technician should do any adjustments

•Improper installation, adjustment, alteration can cause personal injury or property

damage.

•Do not attempt to alter the unit in any manner.

•This appliance must be connected to a 9kg LP gas cylinder.

•Do not move the appliance when in operation.

•Shut off the valve at the gas cylinder or the regulator before moving the

appliance.

•The tubing or the flexible hose must be changed within 2 - 4 years depending on

the condition.

•In case of strong winds attention must be taken against tilting of the appliance.

•Do not store or use gasoline or other flammable vapors or liquids into the heater

unit.

•The whole gas system, hose regulator, pilot or burner should be inspected for

leaks or damages before use.

•All leak tests should be done with a soap solution. Never use an open flame to

check for leaks.

•Do not use the heater until all connections have been leak tested.

•Immediately turn off the gas valve if a smell of gas is detected.

•Do not transport heater while it is in operation.

•Do not move the heater after it has been turned off and the temperature has

cooled down.

•Keep the ventilation opening of the cylinder enclosure free and clear of debris.

•Do not paint radiant screen, control panel or top canopy reflector.

•Control compartment, burner and circulation air passageways of the heater must

be kept clean.

•Frequent cleaning may be required as necessary.

•The LP gas cylinder should be turned off when the heater is not in use.

•Check the heater immediately if any of the following exists:

oThe heater does not reach temperature.

oThe burner makes popping noise during use (a slight noise is normal when

the burner is extinguished).

oSmell of gas in conjunction with extreme yellow tipping of the burner

flames.

•The LP Gas regulator/hose assembly must be located out of pathways where

people may trip over it or in an area where the hose will be subject to accidental

damage.

•Any guard or other protective device removed for servicing the heater must be

replaced before operating the heater.

•Change the gas cylinder in a well-ventilated area, away from any ignition source.

•Check that the regulator seal is fitted and that it is in good condition.

•Do not obstruct the ventilation holes of cylinder housing.

•Adults and children should stay form high temperature surface to avoid burns or

clothing ignition.

•Children should be carefully supervised when they are in the area of the heater.

•Clothing or other flammable materials should not be hung on the heater or placed

on or near the heater.

•The user may replace the rubber hose by himself/herself and must not be longer

than 60cm. The hose must be suitable for LP Gas and comply with SANS 1156.

LP Gas Characteristics - Flammable, explosive, heavier than air-settles in low areas.

In its natural state, LP Gas has no odor. For your safety, an odorant is added to assist in

leak detection.

•Contact with liquid LP Gas can cause freeze burns to skin.

•This heater is shipped from the factory for use with LP Gas only.

•Use only an approved ”9kg” LP Gas cylinder (same as commonly used on gas grills)

with safety valves.

•Never use a cylinder with a damaged body, valve, collar or foot ring.

•When heater is not in use, turn Control Valve OFF. Close the valve of the gas

cylinder or the regulator after use.

•The use of this appliance in enclosed areas can be dangerous and is

PROHIBITED.

1) For use outdoors or in amply ventilated areas.

2) An amply ventilated area must have a minimum of 25% of the surface area open.

3) The surface area is the sum of the walls surface.

HEATER STAND AND LOCATION

•The heater is primarily for outdoor use only.

Always ensure that adequate fresh air

ventilation is provided.

•Always maintain proper clearance to

combustible materials, i.e. top 2m and sides

2m minimum. Heater must be placed on

level firm ground.

•Never operate heater in an explosive

atmosphere like areas where gasoline or

other flammable liquids or vapors are

stored.

•To protect heater from strong wind, anchor the base securely to the ground with

screws.

GAS REQUIREMENTS

•For use with LP Gas mix only.

•LP Gas regulator must be a 2, 8kPa regulator that complies with the requirements of

SANS1237.

•The hose assembly to be used must conform to local standard codes.

•The installation must conform to local codes, or in the absence of codes, with the

standard for storage and handling of liquid petroleum gases. SANS 1539:2012

•A dented, rusted or damaged LP gas cylinder may be hazardous and should be

checked by your cylinder supplier.

•Never use a LP gas cylinder with a damaged valve connection.

•The LP gas cylinder must be arranged to provide for vapor withdrawal from the

operating cylinder.

•Never connect an unregulated LP gas cylinder to the heater.

LEAKAGE TEST

Gas connections on the heater are leak tested at the factory prior to shipment. A complete

gas tightness check must be performed at the installation site due to possible mishandling

in shipment or excessive pressure being applied to the heater.

•The heater must be checked with a full LP gas cylinder.

•Make sure the safety control valve is in the OFF position.

•Make a soap solution of one part liquid detergent and one part water. The soap

solution can be applied with a spray bottle, brush or rag.

•Soap bubbles will appear in case of a leak.

•Leakage test points. See pictures below.

•Turn the gas supply ON.

•In case of a leak, turn off the gas supply.

•Tighten any leaking fittings, then turn the gas supply on and recheck.

•Contact your dealer for assistance if bubbles continue to appear.

•Never leak test while smoking.

FUEL GAS ODOUR

LP Gas has an added odorant to specifically assist on the detection of fuel gas leaks. If a

gas leak occurs you should be able to smell the fuel gas. Since LP Gas is heavier than air

you should smell for the gas odour low to the floor. ANY GAS ODOUR IS YOUR

SIGNAL TO GO INTO IMMEDIATE ACTION!

•Do not take any action that could ignite the

fuel gas. Do not operate any electrical

switches. Do not pull any power supply or

extension cords. Do not light matches or

any other source of flame. Do not use your

telephone.

•Get everyone out of the building and away

from the area immediately. LP Gas is

heavier than air and may settle in low

areas. When you have reason to suspect

a gas leak, keep out of all low areas.

•Use your neighbor’s phone and call your

LP Gas supplier and your fire department.

Do not reenter the building or area.

•Stay out of the building and away from the

area until declared safe by the firefighters

and your LP Gas supplier.

•FINALLY, let the fuel gas service person

and the firefighters check for escaped gas.

Have them air out the building and area before you return. Properly trained service

people must repair any leaks, check for further leakages, and then relight the appliance

for you.

PRE-OPERATION CHECK

a. Remove the observation window panel

by un-screwing the two bolts.

b. Turn on the LP gas cylinder valve.

c. Spoon several drops (or use a squirt

bottle) of the soap solution onto the

gas hose connection and automatic

valve connection and injector

connection.

d. Inspect the connections and look for

bubbles.

e. If no bubbles appear, the connection is

safe.

f. If bubbles appear, there is a gas leak.

Shut off the LP gas cylinder valve,

loosen and then re-tighten this

connection.

g. Check for leaks again.

h. If bubbles still appear, close the LP gas

cylinder valve and call our customer

service department. Do not attempt to

use the heater.

Hose checking step:

(1) Unscrew M5 X 12 screws from the

pole.

(2) Pull out the head assembly, hose &

regulator from the pole.

(3) Check if there are cracks or worn

sections on the hose. If yes, replace the

hose & regulator immediately.

(4) Check for leaks according to the above

step by step after replacing the hose &

regulator.

LIGHTING INSTRUCTIONS

TO TURN ON THE HEATER

1. Turn the control knob to the “OFF” position

2. Turn on the valve on the gas supply cylinder completely.

3. Press and turn the variable control knob to “LOW” position (counter-clockwise 90º)

4. Press down the variable control knob and hold for 30 seconds. While holding down

the variable control knob after the pilot flame lights.

Note:

•If a new LP gas cylinder has just been connected, please allows at least one

minute for the air in the gas pipeline to purge out through the pilot hole.

•When lighting the pilot flame make sure that the variable control knob is

continuously pressed down while pressing the igniter button. Variable control

knob can be released after the pilot flame lights.

•Pilot flame can be watched and checked from the small round window with

sliding lid located at the bottom of the flame screen (to the left or right side of the

controller).

•If the pilot flame does not light or it goes out, REPEAT STEP 3.

5. After the pilot flame lights, turn the variable control knob to minimum position and

leave it there for 5 minutes or more before turning the knob to desired temperature

position.

6. If burner still does not stay lit, then:

a) Push in gas control knob and turn counter clockwise to the "LOW" position.

b) Keep depressing the control knob, put long stem lighter into the ignition hole on

the emitter screen to light the burner.

TO TURN OFF THE HEATER

1. Push and turn the variable control knob to “OFF” position.

2. Turn off the valve on the LP gas supply cylinder completely.

"+!

FLAME CHARACTERISTICS

The flame pattern at the emitter screen should

be visually checked whenever the heater is

operated. Normally the burner flame is blue, but

little yellow flames are acceptable.

If the flames extend beyond the surface of the

emitter grid, or the phenomena of flame lift or

burn-back, or black spots are accumulating on

the emitter grid or reflector, the heater should

be turned off immediately. The heater should

not be operated again until the unit is serviced

or repaired.

STORAGE

1. Always close the gas valve of the LP gas cylinder after use or in case of a disturbance.

2. Remove the pressure regulator and the hose.

3. Check the tightness of the gas valve and for damage. If you suspect damage, have it

changed by your gas dealer.

4. Never store a LP gas cylinder in a sub-terrain environment, or at places without

adequate air ventilation.

CLEANING AND MAINTENANCE

To enjoy years of outstanding performance from your heater make sure you perform the

following maintenance activities on a regular basis:

•Keep exterior surfaces clean.

•Use warm soapy water for cleaning. Never use flammable of corrosive cleaning

agents.

•While washing your unit, be sure to keep the area around the burner and pilot

assembly dry at all times. If the gas control is exposed to water in any way, do NOT

try to use it. It must be replaced.

•Keep the appliance area free and clean from combustible materials, gasoline and

other flammable vapors and liquids; not obstructing the flow of combustion and

ventilation air; keeping the ventilation opening(s) of the cylinder enclosure free and

clear from debris.

•Visually check burner flames.

•Un-screw the screws on pole to remove the burner head assembly.

•Check if there are cracks or worn sections on hose. If yes, please call our customer

service to replace hose.

•At least once a year, the unit should be inspected for the presence of spiders, spider

webs or other insects.

•Airflow must be unobstructed. Keep controls, burner, and circulating air

passageways clean. Signs of possible blockage include:

•Gas odor with extreme yellow tipping of flame.

Indice

Altri manuali Megamaster Riscaldatore da esterno

Megamaster

Megamaster MODO FIRE PIT - Y3 Guida di riferimento rapido

Manuali Riscaldatore da esterno popolari di altre marche

empasa

empasa HMXD-E-NHS Manuale utente

Sunred

Sunred Indus Manuale utente

HEAT1

HEAT1 ECO pro-line 2300W Manuale utente

Heatmaxx

Heatmaxx SRPH98 Manuale utente

Sunjoy

Sunjoy A30600640 Manuale utente

Event Furniture

Event Furniture 16091 Guida alla risoluzione dei problemi

Prem-I-Air

Prem-I-Air EH1462 Manuale utente

Blumfeldt

Blumfeldt 10028637 Manuale utente

Sunjoy

Sunjoy L-PH011PSS-2 Manuale utente

Melissa

Melissa 670-202 Manuale utente

Quality Heating

Quality Heating THE-12DW Manuale utente

DCS

DCS PHFS-P4 Guida all'installazione

EUROM

EUROM 334241 Manuale utente

Lava Heat

Lava Heat Venetian Manuale utente

EHS Ltd.

EHS Ltd. HQH-2000W Manuale utente

VONROC

VONROC ALICUDI PH515AC Manuale utente

OZONA

OZONA Heatflow IF010997 Manuale operativo e di manutenzione

theBBQshop

theBBQshop 51611010 Guida all'installazione