Megavoice LifeLight Manuale utente

LIFELIGHT

SOLAR AUDIO DEVICE

USER MANUAL

TABLE OF CONTENTS

Easy Start 1

Turning the LifeLight On/Off 1

The LCD Screen 1

Volume 1

Selecting Playback Channels 2

Navigating During Playback 2

Playback Screen 2

File Playback Information 3

Fast Reverse/Fast Forward 3

Pausing/Bookmarking 3

Loading Audio Files 4

Supported File Types 4

Radio 5

Radio Screen 5

Conguration File 5

Speed Control 5

Speed Control Screen 6

Lantern 6

Reading Light 7

LED Torch 7

Hanging Hook 7

Silicon Connectors Cover 7

Using the MicroSD Card 7

Charging/Communication Modes 8

Earphones and Speaker 9

AM/FM Antenna Jacks 9

Resetting Device Defaults 9

Full Device Reset 9

The Menu System 10

The Menu System Screens 10

Charging Instructions 12

Charging Screen 12

Battery Care 13

Problems With the LifeLight 13

Warnings 13

Reset Button 13

1/13

EASY START

Press and hold until the device chimes and the LCD screen turns on. Playback will automatically begin.

TURNING THE LIFELIGHT ON/OFF

Press on for 2 seconds to turn the device On (the LCD screen will turn On and the device will chime). A welcome

screen will display and audio playback/radio will begin immediately.

Press on for 2 seconds to turn the device Off.

The device will chime again, the shutdown screen will display and the LCD screen will turn Off.

The device will remember its last mode and playback position/band & frequency when turned off.

THE LCD SCREEN

This LifeLight is unique and provides complete information and control via the LCD screen with an interactive menu

system.

The screen has a backlight, which is activated when the device is turned On, turned Off, or when is pressed. The

backlight turns off automatically after 30 seconds of keypad inactivity.

The information on the screen is always current as modes, content and settings change.

For more detail, see illustrations of various screens throughout this manual.

VOLUME

Click or to decrease or increase volume by one level.

The rst click automatically displays the volume adjustment screen.

Press and hold will continue to decrease/increase until the minimum (00) or maximum (10) is reached. When the

volume is set to minimum or maximum a chime is played.

The volume will remain set at this level even after the device is turned off and restarted.

After 1 second of inactivity, the volume screen will timeout and return to the previous screen.

Separate volume levels are maintained for audio playback and radio.

2/13

SELECTING PLAYBACK CHANNELS

The device supports up to 3 Channels for onboard memory and up to 2 Channels for microSD.

For both memory sources, there should be at least one of Channels 001 and 002 containing audio content.

When in playback mode, a 2-second press on will navigate to the last playback position of the other Channel (if

present).

Channel 000 (optional/onboard only) is typically reserved for a device introduction and/or audible user manual. If a

Channel 000 is present, playback will always begin from it when the Device is rst turned on (or after the Device is

reset).

When in playback from onboard or microSD memory, a 2-second press on and together will navigate to the

last playback position in Channel 000 (if present) of onboard memory.

From Radio Mode, a 2-second press on will resume playback at the prior position in onboard memory.

NAVIGATING DURING PLAYBACK

Each Channel is subdivided into one or more Sections, containing one or more Books, containing one or more

Chapters.

Click to skip to the next Section within the current Channel.

Click or to skip backward or forward one Book. A 2-second press will skip 5 Books at a time. Press and hold will

continue until the button is released or the beginning/end of the Section is reached.

Click or to skip backward or forward one Chapter (le). A 2-second press will skip 5 Chapters at a time. Press

and hold will continue until the button is released or the beginning/end of the Book is reached.

Click or to jump backward or forward 20 seconds in the current le. Press and hold will perform a fast rewind/

fast forward (in 10-second increments ) until the button is released or the beginning/end of the le is reached.

To quickly return to the start of a Channel, while in Pause Mode press for 2 seconds.

Actual time may vary.

While in audio playback mode, the Playback screen is displayed.

During “press and hold”, a scale will be displayed on the bottom line of the screen showing the current playback position

within the total play time of the current le. See FAST REVERSE/FAST FORWARD for more details.

PLAYBACK SCREEN

Playback

indicator:

currently playing

Onboard memory

is current source

AM/PM (or blank

when 24-hour)

microSD is loaded

Clock

Charge indicator:

Blinking when

active, static

when full, blank

when not

connected to

power source

3/13

Icon representing

type of file

information

Audio device is

connected

Not connected

for charging

Battery capacity

indicator: four

bars = 81%-100%

Paused

microSD memory

is current source

Current file

information

FILE PLAYBACK INFORMATION

Available audio le metadata tags are displayed for each le in the following way:

• Track info: + ID3 Track Name

- If Track Name is blank or missing, + Filename.extension

• Album Info: + ID3 Album Name

- If ID3 Album Name is blank or missing, the eld is skipped

• Artist info: + ID3 Artist Name

- If ID3 Artist Name is blank or missing, the eld is skipped

• If ID3 metadata is completely missing

- The device will display only + Filename.extension

• If any tag text is longer than the screen area , it scrolls from right to left

- The eld will show for 3 seconds before scrolling begins

- Once scrolling has nished the next eld is displayed

Any tag text longer than 44 characters will be truncated.

Typically about 13 characters.

FAST REVERSE/FAST FORWARD

Total playback

time

Current playback

position

Current position

indicator

Fast reverse

is being executed

Fast forward

is being executed

During playback, a continuous press on or will fast reverse/fast forward through the current le.

The device will overlay the bottom row of the screen with the current and total playback times in HH:MM:SS format.

The current playback position relative to the total is illustrated by a bar on the scale. As the scan occurs the playback

position is updated accordingly. Once you release the or buttons, the scale will linger for a few seconds but is

then hidden when the le information is redisplayed.

PAUSING/BOOKMARKING

While in audio playback mode, click to pause playback. The icon is displayed.

To resume, click again. The icon is displayed.

4/13

LOADING AUDIO FILES

The recommended method for loading audio to LifeLight is with a Windows application named SaberCopy. SaberCopy

is free to use and may be downloaded from our web site here:

https://megavoice.com/audio-tools/sabercopy-loading-system-for-audio-bibles/

Please download the installation le and user guide for reference. The installation is a typical Windows installation and

takes about 10 seconds.

Once installed, the simplest method for loading is to open the template project for LifeLight as it is already congured

with the recommended settings. (see section “Template Projects” in the user guide)

All you need to do is to specify the audio folder you wish to load on the “Files in Project” tab. SaberCopy will check

your audio against folder and le rules dened for LifeLight on the “Target Device” tab.

To access the onboard memory of the LifeLight and update the contents, a special SLS USB cable must be used. These

cables are only available from MegaVoice.

For assistance, please contact us at:

https://megavoice.com/support

SUPPORTED FILE TYPES

File Type Limitations Unsupported

APE

Bit rate: Fast/Normal compression (800Kbps-1000Kbps)

Sampling rate: 8KHz-48KHz

Bit depth: 16bit

“Insane” (ultra-high) compression setting

FLAC

Bit rate: L0 - L8 (1000Kbps-1200Kbps)

Sampling rate: 8KHz-48KHz

Bit depth: 16bit

MP3 Bit rate: 8kbps - 320kbps

Sampling rate: 8KHz-48KHz

OGG Bit rate: Q0 - Q10 (20kbps-499kbps)

Sampling rate: 8KHz-48KHz

WAV

IMA-ADPCM

Bit rate: 32kbps - 384kbps

Sampling rate: 8KHz-48KHz

Bit depth: 16bit

MS-ADPCM

Bit rate: 32kbps - 384kbps

Sampling rate: 8KHz-48KHz

Bit depth: 16bit

PCM

Bit rate: 128kbps - 1536kbps

Sampling rate: 8KHz-48KHz

Bit depth: 16bit

WMA Bit rate: 5kbps - 384kbps

Sampling rate: 8KHz-48KHz

WMA lossless or WMA PRO

For both onboard and microSD memory, the device automatically bookmarks the last le played and the position

within that le when the mode is changed or the device is turned off.

The Pause function is only available during audio playback.

If the device is left paused for more than 15 minutes it will turn itself off.

5/13

CONFIGURATION FILE

Default Device and radio settings can be controlled by a conguration le stored in the root folder of the Device.

The SET.TXT le can be used to congure startup mode, default radio band, assign frequencies to the programmable

buttons, and more.

To download a sample le including instructions please use the link below:

https://megavoice.com/downloads/set.txt.zip

SPEED CONTROL

A click on will emit a chime and place the Device in speed control mode, allowing you to adjust the audio playback

speed.

While in speed control mode, the speed control adjustment screen is displayed.

A click on or will adjust playback speed by one level. Press and hold will decrease/increase until the minimum

(-8) or maximum (+8) speed is reached.

RADIO

When in playback mode, a 2-second press on will put the Device in radio mode (Device will chime). The radio will

begin to play from the last band used and the last frequency set.

If already in Radio mode, a click on will cycle through the available bands: FM and AM. While in Radio Mode, a

2-second press on will resume Playback Mode from the last position in onboard memory (Device chimes again).

While in Radio mode the Radio screen is displayed.

Click or to decrease/increase the frequency by a pre-set value for the current band. A 2-second press will scan

for the previous/next station of the current band. The frequency display will update as it changes.

When the scan reaches the beginning/end of the band’s frequency range the Device will chime. An additional click will

loop and continue the scan from the beginning/end respectively. To stop an active scan , click on .

The buttons may be pre-programmed with individual default frequencies per band. A click on each will

tune the radio to the setting for that button. A 2-second press will set (or reset) that button to the current frequency.

When the frequency is tuned to one of the programmable buttons ( ), that button’s symbol will be displayed on

the bottom right of the screen.

See Radio Band Spacing Screen for details.

FM: 64.0-108.0 MHz, AM: 520-1720 kHz

While scanning is active, you cannot change mode or turn the Device off.

RADIO SCREEN

Current band:

FM or AM

AM/PM (or blank

when 24-hour)

microSD is loaded

Clock Current frequency

Battery capacity

indicator: four

bars = 81%-100%

When current

frequency is

tuned to one of 3

programmable

buttons, the

button image

shows here

Unit of frequency

measurement

6/13

SPEED CONTROL SCREEN

Click again to exit and save the setting. Pressing any other button will exit speed control mode without saving

changes.

To reset the speed to normal (+0), enter speed control mode, then press again for 2 seconds. The Device will return

to playback mode at normal speed.

The Speed setting persists when changing modes or after turning the device off.

The Speed setting applies to both onboard and microSD playback.

The Speed Control button is only active during audio playback and may be set while playback is active or paused.

Speed Control may also be set via the Settings Menu. A click on will also save a speed setting change.

Current speed setting: from -8 to +8 Identifies Speed settings screen

• This is the screen that is displayed when entering Speed Control Mode from playback.

• The same screen is accessible from the Device’s Settings Menu by selecting the icon.

Speed Control only works correctly with MP3, WAV and WMA type audio les!

Due to an IC limitation, when Speed Control is active, only the left channel (stereo) is audible.

LANTERN

A click on will turn on the Lantern on Low intensity according to the following loop :

Back

Front

Back

Front

Back

Front

Back

Front

Whether the Lantern is on/off, a 2-seconds press on will cause both Back and Front sides to continuously blink in

High intensity. An additional 2-seconds press will turn both Back and Front sides off.

The loop will continue according to the Lantern’s current position in the loop (e.g., if the Lantern’s Back side is on, a click

will turn the Back side off and Front side on).

The Lantern may be used while other functions are active or device is off.

When either or both sides of the Lantern are on, a click on will change the Lantern’s light intensity as follows:

Low > Medium > High

7/13

LED TORCH

READING LIGHT

HANGING HOOK

Use to control the LED Torch and its intensity. Each click will change the intensity as follows:

Low > Medium > High > OFF

Press and hold to turn on the Torch in High intensity. The Torch will stay on until the button is released.

The Torch may be used while other functions are active or device is off.

Use to control the Reading Light and its intensity. Each click will change the intensity as follows:

Ultra-Low > Low > Medium > High > OFF

When the Reading Light is on, a 2-seconds press on will turn off the Reading Light.

The Reading Light may be used while other functions are active or device is off.

You may hang the Device using its Hanging Hook to various objects such as strings, coat hangers, etc.

The Hanging Hook can rotate 360° and while the device is suspended, it may be used normally.

SILICON CONNECTORS COVER

Open the Silicon Connectors Cover from the tab on the bottom to uncover the device’s connectors .

In order to keep the connectors exposed, the Silicon Connectors Cover must be held against the device.

The Silicon Connectors Cover can be closed by returning it to its place and pressing it in.

USING THE MICROSD CARD

The device can also play audio from a properly structured microSD card. With the device facing you, insert the card

with the brass contacts showing until it locks in place.

Gently

pull the

Hanging

Hook

8/13

CHARGING/COMMUNICATION MODES

When the device is off and a charge-only cable is connected:

• The device will enter charging mode and the charge screen is displayed.

• When the cable is disconnected, charging stops and the device remains off.

When the device is on and a charge-only cable is connected:

• The current function will continue uninterrupted but the icon is displayed.

• The icon will blink while charging and stop blinking once fully charged.

• When the cable is disconnected, the icon is hidden, charging will cease and the current function continues.

When the device is off and a data-only or SLS cable is connected:

• The computer connection screen is displayed.

• Access to the onboard memory and/or microSD is possible.

Once a card is loaded, the icon appears on the screen. To change to microSD playback, click to display the Main

Menu. Navigate to the microSD symbol using or and click again. Playback will now begin from the card.

To remove a card, gently push it in. The reader will unlock and push it out so you can remove it. If the device was in

playback mode from the card when removed, it will display “No microSD” and enter Menu Mode. If any other function

was active, it will continue with no change.

You can view, format and prepare a microSD card while loaded in the device’s card reader when the device is

connected to a Computer using a USB to micro-USB cable. You may also do the same with the card loaded in a

microSD adaptor connected to a Computer.

Up to 2 microSD cards can be stored on the bottom side of the Silicon Connectors Cover, please see the “SILICON

CONNECTORS COVER” section on how to open and close the Silicon Connectors Cover.

Whenever a microSD card is inserted or removed a chime is played.

Content on a microSD card must be encrypted to work on this device. Contact your sales representative for details.

The write speed of a card adaptor connected directly to a computer is signicantly faster than the internal card reader.

Some ID3 tags may not be displayed for content on microSD.

MicroSD

Card

9/13

• When the cable is disconnected, the device remains off.

When the device is on and a data-only or SLS cable is connected:

• The current function will continue uninterrupted but the charge icon is displayed.

• The icon will blink while charging and stop blinking once fully charged.

• When the cable is disconnected, the icon is hidden, charging will cease and the current function continues.

Changing to Computer Communication mode is essential to allow programming of the device and/or Firmware update.

Whenever any USB cable is connected or disconnected a chime will be played.

EARPHONES AND SPEAKER

AM/FM ANTENNA JACKS

RESETTING DEVICE DEFAULTS

FULL DEVICE RESET

Insert earphone or speaker plug into the 3.5mm stereo audio jack under the micro-USB port. When an audio device is

connected, the internal speaker will turn off. When disconnected, speaker will turn back on, and the device will enter

Pause Mode.

The volume levels operate as written under the “VOLUME” section.

While an audio device is connected, the icon is displayed on the screen.

When an audio device is removed during audio playback, the device enters Pause Mode.

Some earphones with built-in controls may not work properly.

There are two 3.5mm antenna jacks, one for AM radio and another for FM radio . Using the correct antenna,

these jacks can be used to increase the reception of the AM/FM radio.

The device’s default settings may be reset at any time and at the following levels:

• Onboard Playback: all onboard bookmarks

• microSD Playback: all microSD bookmarks

• Radio - per band: last frequency, programmable buttons, frequency spacing

• Speed Control: reset speed to normal (0)

• Full reset: all the above + reset volume to normal (6)

The Main Menu offers a sub-menu of mode reset screens. From the sub-menu, choose the mode reset icon for

each of the above.

To perform a full reset of the device do the following:

• Click to enter the Main Menu.

• Press and hold and together for 2 seconds.

• The full reset menu is displayed: Highlight and select the conrmation icon .

• The conrmation menu is displayed: Highlight and select the tick icon .

• “Device Reset Successful!” is displayed.

Altri manuali per LifeLight

Indice

Altri manuali Megavoice Lanterna

Megavoice

Megavoice LifeLight Manuale utente

Manuali Lanterna popolari di altre marche

KYOWA

KYOWA KW-9114 Manuale utente

Stahl

Stahl ECOLUX 6610 Series Manuale utente

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuale utente

PRG

PRG VARI LITE VL5 Manuale utente

Raytec

Raytec VARIO2 series Manuale utente

ENSA

ENSA LEDBT18WS2 Manuale utente

LUG

LUG OFFICE LB LED N/T Manuale utente

GE Wallighter 250 Manuale utente

Draper

Draper RLEDL19/B Manuale utente

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuale utente

Panasonic

Panasonic EY3741B57 Manuale utente

Clas Ohlson

Clas Ohlson LCC8T Manuale utente

Coolon

Coolon WDN-140 Manuale utente

Holiday Travel

Holiday Travel 834873 Manuale utente

BEGA

BEGA 84 036 Manuale utente

BEGA

BEGA 33 596 Manuale utente

Dale Tiffany

Dale Tiffany GT701162 Manuale utente

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuale utente