Megger B10E Manuale utente
B10E
Power Supply Unit
Art No. ZP-BG02E Doc. BG0140ME V04a 2019
WWW.MEGGER.COM
User’s Manual
B10E
Power Supply Unit
NOTICE OF COPYRIGHT & PROPRIETARY RIGHTS
© 2017-2019, Megger Sweden AB. All rights reserved.
The contents of this manual are the property of Megger Sweden AB. No part of this work may be reproduced or transmitted in any form or
by any means, except as permitted in written license agreement with Megger Sweden AB. Megger Sweden AB has made every reasonable
attempt to ensure the completeness and accuracy of this document. However, the information contained in this manual is subject to change
without notice, and does not represent a commitment on the part of Megger Sweden AB. Any attached hardware schematics and technical
descriptions, or software listings that disclose source code, are for informational purposes only. Reproduction in whole or in part to create
working hardware or software for other than Megger Sweden AB products is strictly prohibited, except as permitted by written license
agreement with Megger Sweden AB.
This device contains software that is licensed under the General Public License (GPL). If requested, a copy of the source code licensed under
the GPL can be sent to you. Please e-mail your request to se-gplrequest@megger.com. Please note that no questions regarding the content
of the source code can be answered. You may be charged a fee covering the costs of sending you the source code.
TRADEMARK NOTICES
Megger® and Programma® are trademarks registered in the U.S. and other countries. All other brand and product names mentioned in this
document are trademarks or registered trademarks of their respective companies.
Megger Sweden AB is certified according to ISO 9001 and 14001.
User’s Manual
Postal address: Visiting address:
Megger Sweden AB Megger Sweden AB
Box 724 Rinkebyvägen 19
SE-182 17 DANDERYD SE-182 36 DANDERYD
SWEDEN SWEDEN
T+46 8 510 195 00
Eseinfo@megger.com
www.megger.com
BG0140ME ZP-BG02E B10E 3
Contents
1 General
............................................................. 6
1.1 Introduction........................................................ 6
1.2 Service and support ............................................ 6
Contact Information ........................................... 6
Checklist before calling/e-mailing for support......6
Shipping ............................................................. 6
2 Safety
............................................................. 8
2.1 General............................................................... 8
Symbols on the instrument ................................. 8
2.2 Safety instructions.......................................................8
3 Control panel
........................................................... 10
4 Operating instructions
........................................................... 12
4.1 Circuit breaker trigging ..................................... 12
Application examples........................................ 12
4.2 Troubleshooting................................................ 13
5 Specifications
........................................................... 14
4B10E ZP-BG02E BG0140ME
BG0140ME ZP-BG02E B10E 5
1General
1.1 Introduction
Power Supply Unit B10E is used to supply voltage to
the Circuit Breaker (CB) coils and spring-charging mo-
tor during installation and/or field service.
Since the high-quality voltage available at the coil
outputs is very load-independent, the power supplied
resembles what is encountered under normal oper-
ating conditions. Circuit breaker functionality thus
remains virtually unchanged.
B10E enables you to test CB functions easily at the
specified voltage levels.
1.2 Service and support
For technical assistance please contact your local
Megger representative or direct your request to the
office in Sweden.
Contact Information
Internet: www.megger.com
E-mail: support-sweden@megger.com
Tel: +46 8 510 195 00
Checklist before calling/e-mailing
for support
▪Read the manual
▪Restart the instrument(-s), redo test connections and try
again
▪Try to repeat the failing operation if possible
▪Identify the instrument model and serial number.
Shipping
If you are going to send the instrument with parcel
service use the original transport box or one with
equivalent strength. Megger can not take responsibil-
ity for transport damages.
6B10E ZP-BG02E BG0140ME
1 GENERAL
BG0140ME ZP-BG02E B10E 7
1 GENERAL
2.1 General
▪Always follow the local safety regulations that apply to
work with high-voltage equipment.
▪Read and comply with the following safety instructions.
Symbols on the instrument
Caution, refer to accompanying docu-
ments.
Protective conductor terminal.
WEEE, Waste Electrical and Electronic
Equipment. Please utilize your local
WEEE collection facilities in the dispo-
sition of this product and otherwise
observe all applicable requirements.
The unit can also be returned to Megger
at any time at no charge for the disposal.
2Safety
2.2 Safety instructions
WARNING
1Always make certain that the DC system in the
substation is disconnected before connecting
B10E.
2Always ground the B10E.
3Before connecting B10E, turn off its master ON/
OFF switch.
4Only connect B10E to an outlet protected with
max 16 A overcurrent protection
5High voltage/current on input/output terminals.
6Do not attempt to service the instrument your-
self. Opening or removing covers may expose
you to dangerous voltage. If you attempt to
service the instrument yourself the warranty is no
longer valid.
7Do not use any accessories that are not intended
for use together with the instrument.
8Disconnect the instrument from the mains before
cleaning. Use a damp cloth for cleaning. Do not
use liquid cleaners or aerosol cleaners.
8B10E ZP-BG02E BG0140ME
2 SAFETY
IMPORTANT
1Always use safety connecting leads.
2Never leave the instrument unattended while it is
turned on.
3Use only approved mains detachable cable set
with the instrument. Main supply cables shall be
rated for the maximum current for the equip-
ment and the cable shall meet the requirements
of IEC 60227 or IEC 60245. Mains supply cables
certified or approved by a recognized testing au-
thority are regarded as meeting this requirement.
4Unplug the instrument from the mains supply
when it is left unattended or not in use.
5Refer all servicing to Megger authorized person-
nel.
6If you need to return the instrument, please use
either the original crate or one of equivalent
strength
BG0140ME ZP-BG02E B10E 9
2 SAFETY
3Control panel
1Output for DC voltage supplied to closing/
breaking coil
2Output for AC voltage supplied to closing/
breaking coil
3F2. 4 A fuse for AC outputs
4Changeover switch used to select either DC or
AC coil outputs
5Changeover switch used to select either coil
outputs or spring-charging motor outputs
6DC voltage outputs for spring-charging motor.
Provide unsmoothed, half-wave rectified DC
ranging up to 18 A
7Button for turning on spring-charging motor
voltage
8Current shunt output used to measure current,
in coils or spring-charging motors (max 5 A
continuous)
9Voltmeter
10 Input for external trig signal or short-circuiting
jumper
11 Button for manual trigging pulse via coil out-
puts. (Switch 12 set to voltage position)
12 Changeover switch used to select either con-
tact sensing or voltage sensing at the trig input
13 Reset button for thermal, overload and/or time-
limit cut-outs
14 Variable transformer
15 Master ON/OFF switch
16 Inlet for mains power
17 F1. 7 A miniature circuit breaker for DC spring-
charging motor
18 Grounding terminal
19 Changeover switches (A) and (B) for incoming
power 115/230/135/250 V AC
❻
❼❸ ❹ ❺
❽ ➒
❿
➊
⓫ ⓬ ⓭
⓮
⓯
⓰
❷
⓱
⓳
⓲
⓫ ⓬
10 B10E ZP-BG02E BG0140ME
3 CONTROL PANEL
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Megger Alimentazione elettrica
