Melive T86+ Manuale utente
Melive Technology Co., Ltd
- 1 -
User Manual
Model : T86+ WiFi Action Camera
Made by: Melive Technology Co., Ltd
Version: Melive-V1.0
Melive Technology Co., Ltd
- 2 -
Product Diagram
A WiFi Activation (Down select) F POWER(and menu)
B LED power indicator G USB interface
C LCD screen H Micro SD card port
D SHOOT (menu select) I Mini HDMI interface
E Microphone J Removable Li-Battery
Melive Technology Co., Ltd
- 3 -
Left Side Right Side
Remote Diagram
Please note: with the remote controller you cannot turn the camera on.
Please ensure the camera is switched on before using the remote.
A LED Indicators
B Shoot Photo
C Record Video
D Power Off
E Micro USB Charge port on the back of remote
Melive Technology Co., Ltd
- 4 -
Press and hold the “Power off” button for 4sec. to turn the camera off.
To use the remote, please code first before power on the camera.
Coding procedures:
1. Press and hold the “Picture” & “Video” keys of the remote at the same
time, then turn the camera on;
2. When the camera enters into the real live interface, release the
“Picture” & “Video” keys;
3. The middle blue indicator lights up, then the coding is finished.
Note:
Please keep holding the “Picture” & “Video” keys during coding;
Only need to code once, afterwords the camera will recognize
automatically;
WiFi function & remote controller can not be used simultaneously.
Setup Your T86+
Turn the camera on- press and hold the POWER button for several
seconds.
When the camera is on, the Melive logo will appear on the screen and the
three red LED lights will glow red. The camera is now in video mode.
Melive Technology Co., Ltd
- 5 -
Red LED light
Red LED light
Red LED light
Melive Technology Co., Ltd
- 6 -
Video Mode
Video mode screen
Once the camera is turned on, it goes to the video capture mode by
default. Press SHOOT button to start recording. When the recording
starts, you will see the red lights start flashing. To end recording, press
the SHOOT button again.
To enter the Settings menu, press the POWER button (press and release
immediately-if it is held too long the camera will switch off).
Note: The Setup menu is depending on the active mode. If the video
mode is active, it will display video capture settings or if the Picture mode
is active, it will display the Image capture settings.
By default, video mode is the active mode when you turn the device on.
Melive Technology Co., Ltd
- 7 -
Video Settings
Video Settings Screen
This allows user to adjust Video quality settings.
Navigation: Use WiFi button to navigate, SHOOT button to Enter/Confirm
selection, POWER button to go back.
Resolution
This allows user to set the recording video resolution:
1080P 60fps
1080P 30fps
720P 120fps
720P 60fps
Video Looping
This allows user to set record duration
OFF-In this mode, camera will generate new file on every 25 mins
1 Min-In this mode, camera will generate new file on every 1 mins
Melive Technology Co., Ltd
- 8 -
3 Mins- In this mode, camera will generate new file on every 3 mins
5 Mins- In this mode, camera will generate new file on every 5 mins
White Balance
Factory default is Auto. If you switch Auto OFF, remember to adjust when
lighting conditions change.
Following pre-set modes are also available
Daylight, Cloudy, Tungsten, Fluor
Microphone
SELECT Outdoor or Car to record in different scenes with better audio
effect, SELECT OFF for video only.
Date Stamp
Off: to turn off displaying date stamp on captures
Date: to display date on captures
Date & Time: to display date& time on captures
Melive Technology Co., Ltd
- 9 -
General Settings
General Settings Screen (Page 1)
This allows user to adjust the general device settings
To enter General Settings, enter the Settings menu first by pressing
POWER button, then press and hold the SHOOT button for 3secs
Navigation: Use WiFi button to navigate, SHOOT button to Enter/Confirm
selection, POWER button to go back.
Auto LCD Off
This will determine if the LCD will turn off after 1 min, 3 min or 5 min.
Press any key to turn the screen on.
Select OFF to keep the screen always ON.
Auto Power Off
To set Auto Power off function
Melive Technology Co., Ltd
- 10 -
Date & Time
This allows user to adjust the date &time.
Note: Use the WiFi button to change the date and time, use SHOOT
button to confirm. The date is entered in Year/Month/Day format. Time is
based on a 24hr clock.
Language
To select the device language
Light Frequency
Selecting the correct light frequency will avoid the possibility for strobing.
General Setting Screen (Page 2)
Screen rotation
To rotate the screen
Indice
