MEN CompactPCI F600-3U Manuale utente
®
Embedded Solutions
F600 – 3U CompactPCI®
Side Card for SATA/Legacy I/O
20F600-00 E2 – 2008-03-03
User Manual
Configuration example
F600 - 3U CompactPCI Side Card for SATA/Legacy I/O
MEN Mikro Elektronik GmbH 2
20F600-00 E2 – 2008-03-03
F600 - 3U CompactPCI Side Card for SATA/Legacy I/O
The F600 is a 4HP legacy I/O extension card for 3U Intel® based CompactPCI®
single-board computers such as F14, F15, F17, F18 and further boards of the Intel®
low power family.
Modern Intel® based boards increasingly support USB interfaces as an exclusive
universal connection of devices such as keyboard, mouse, CD-ROM, floppy etc.
Especially in industrial applications however many existing systems still use COM
interfaces.
The F600 provides SA-Adapter™ slots for up to four additional COMs, two at the
front panel and two on board. Since SA-Adapters™ provide the physical layers, the
F600 can be configured flexibly with a combination of RS232, RS422 or RS485
interfaces, alternatively isolated or not isolated. In addition an on-board 2.5" SATA
hard-disk slot can be used on the standard version of the F600, which comes with
two COM interfaces.
The F600 is directly plugged to the right side of the respective single-board
computer. A robust connector makes for high mechanical stability. It is delivered
with an 8HP front panel, replacing the 4HP front panel of a 3U single-board
computer and thus resulting in a solid one-piece front panel.
Technical Data
MEN Mikro Elektronik GmbH 3
20F600-00 E2 – 2008-03-03
Technical Data
I/O
• Up to four UARTs
- From four CPU-controlled USB channels
- Two at front panel
- Two on board, instead of on-board SATA device, on request
- Physical interface using SA-Adapters™ via 10-pin connectors
- RS232..RS485, isolated or not: for free use in system (e. g. cable to front)
- Data rates up to 1 Mbit/s
- FIFO receive and transmit buffers for high data throughput
- Handshake lines: full support; lines depend on SA-Adapters™
Mass Storage
• Serial IDE (SATA)
- One port for on-board 2.5" hard-disk drive
- One port for external device (e.g. SATA DVD Drive)
- Transfer rates up to 150MB/s (depends on hard disk, 28MB/s for 2.5" hard
disk)
- RAID level 0/1 support (depends on CPU board)
Miscellaneous
• CompactPCI® J1 and J2 are assembled for increased mechanical stability and/or
for power supply via J1
Electrical Specifications
• Supply voltage/power consumption:
- +5V (-3%/+5%), 21mA typ. (with two SA1 SA-Adapters™, w/o hard disk)
- +3.3V (-3%/+5%), 50mA typ. (with two SA1 SA-Adapters™, w/o hard disk)
• MTBF: 1,663,000h @ 40°C (derived from MIL-HDBK-217F)
Mechanical Specifications
• Dimensions: conforming to CompactPCI® specification for 3U boards
• Weight: 145g (w/o hard disk)
Technical Data
MEN Mikro Elektronik GmbH 4
20F600-00 E2 – 2008-03-03
Environmental Specifications
• Temperature range (operation):
- -40..+85°C (depending on hard disk; please refer to the hard disk specifica-
tions for possible limits)
- Airflow: min. 10m³/h
• Temperature range (storage): -40..+85°C
• Relative humidity (operation): max. 95% non-condensing
• Relative humidity (storage): max. 95% non-condensing
• Altitude: -300m to + 3,000m
• Shock: 15g/11ms
• Bump: 10g/16ms
• Vibration (sinusoidal): 2g/10..150Hz
• Conformal coating on request
Safety
• PCB manufactured with a flammability rating of 94V-0 by UL recognized manu-
facturers
EMC
• Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and
IEC1000-4-4 (burst) with regard to CE conformity
Software Support
• Driver software for the UART interface for Windows®, Linux (to be verified),
VxWorks® (to be verified), QNX® (on request)
• For more information on supported operating system versions and drivers see
online data sheet.
• Further information can be found in the data sheet of the CPU board that you
use.
Block Diagram
MEN Mikro Elektronik GmbH 5
20F600-00 E2 – 2008-03-03
Block Diagram
USB 2.0
USB 2.0
USB 2.0
USB 2.0
IDE (SATA)
Board-to-
Board
Connector
CPU Board
IDE (SATA)
USB-to-
UART bridge F
USB-to-
UART bridge
BOn-board
HDD
USB-to-
UART bridge
USB-to-
UART bridge
External
Device
B
BSA
FB SA
BSA
BSA
F
F
2nd
front
panel
F
B
Front panel
connector
On board
connector
Options
SA SA-Adapter
Configuration Options
MEN Mikro Elektronik GmbH 6
20F600-00 E2 – 2008-03-03
Configuration Options
Mass storage
• CompactFlash® interface instead of SATA hard disk
- Via AD95 adapter
UARTs
• Two additional UARTs instead of on-board SATA hard disk
• 1 to 4 COMs possible
Mechanical
• Side card can be added at left or right side of CPU
Please note that some of these options may only be available for large volumes.
Please ask our sales staff for more information.
Product Safety
MEN Mikro Elektronik GmbH 7
20F600-00 E2 – 2008-03-03
Product Safety
Electrostatic Discharge (ESD)
Computer boards and components contain electrostatic sensitive devices.
Electrostatic discharge (ESD) can damage components. To protect the board and
other components against damage from static electricity, you should follow some
precautions whenever you work on your computer.
• Power down and unplug your computer system when working on the inside.
• Hold components by the edges and try not to touch the IC chips, leads, or cir-
cuitry.
• Use a grounded wrist strap before handling computer components.
• Place components on a grounded antistatic pad or on the bag that came with the
component whenever the components are separated from the system.
• Store the board only in its original ESD-protected packaging. Retain the original
packaging in case you need to return the board to MEN for repair.
!
About this Document
MEN Mikro Elektronik GmbH 8
20F600-00 E2 – 2008-03-03
About this Document
This user manual describes the hardware functions of the board, connection of
peripheral devices and integration into a system. It also provides additional
information for special applications and configurations of the board.
The manual does not include detailed information on individual components (data
sheets etc.). A list of literature is given in the appendix.
History
Conventions
This sign marks important notes or warnings concerning proper functionality of the
product described in this document. You should read them in any case.
Folder, file and function names are printed in italics.
Bold type is used for emphasis.
A monospaced font type is used for hexadecimal numbers, listings, C function
descriptions or wherever appropriate. Hexadecimal numbers are preceded by "0x".
Hyperlinks are printed in blue color.
The globe will show you where hyperlinks lead directly to the Internet, so you can
look for the latest information online.
Signal names followed by "#" or preceded by a slash ("/") indicate that this signal is
either active low or that it becomes active at a falling edge.
Signal directions in signal mnemonics tables generally refer to the corresponding
board or component, "in" meaning "to the board or component", "out" meaning
"coming from it".
Vertical lines on the outer margin signal technical changes to the previous edition of
the document.
Edition Comments Technical Content Date of Issue
E1 First edition M. Himmler 2006-02-21
E2 Update, J1 pin assign-
ment corrected
M. Himmler, K.Schöne 2008-02-29
!
italics
bold
monospace
hyperlink
IRQ
#
/IRQ
in/out
About this Document
MEN Mikro Elektronik GmbH 9
20F600-00 E2 – 2008-03-03
Legal Information
MEN Mikro Elektronik reserves the right to make changes without further notice to any products herein. MEN makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does MEN assume
any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages.
"Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be
validated for each customer application by customer's technical experts.
MEN does not convey any license under its patent rights nor the rights of others.
Unless agreed otherwise, MEN products are not designed, intended, or authorized for use as components in systems intended
for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the MEN product could create a situation where personal injury or death may occur. Should Buyer purchase or
use MEN products for any such unintended or unauthorized application, Buyer shall indemnify and hold MEN and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that MEN was negligent regarding the design or manufacture of the part.
Unless agreed otherwise, the products of MEN Mikro Elektronik are not suited for use in nuclear reactors and for application
in medical appliances used for therapeutical purposes. Application of MEN products in such plants is only possible after the
user has precisely specified the operation environment and after MEN Mikro Elektronik has consequently adapted and
released the product.
ESM™, MDIS™, MDIS4™, MENMON™, M-Module™, M-Modules™, SA-Adapter™, SA-Adapters™, UBox™ and
USM™ are trademarks of MEN Mikro Elektronik GmbH. PC-MIP® is a registered trademark of MEN Micro, Inc. and SBS
Technologies, Inc. MEN Mikro Elektronik®, ESMexpress® and the MEN logo are registered trademarks of MEN Mikro
Elektronik GmbH.
Celeron®, Intel®, PCI Express®, Pentium® and Xeon® are registered trademarks of Intel, Inc.
CompactPCI® is a registered trademark of PCI Industrial Computer Manufacturers Group.
Microsoft® and Windows® are registered trademarks of Microsoft Corp. Windows® Vista™ is a trademark of Microsoft Corp.
QNX® is a registered trademark of QNX Ltd.
Tornado® and VxWorks® are registered trademarks of Wind River Systems, Inc.
All other products or services mentioned in this publication are identified by the trademarks, service marks, or product names
as designated by the companies who market those products. The trademarks and registered trademarks are held by the
companies producing them. Inquiries concerning such trademarks should be made directly to those companies. All other brand
or product names are trademarks or registered trademarks of their respective holders.
Information in this document has been carefully checked and is believed to be accurate as of the date of publication; however,
no responsibility is assumed for inaccuracies. MEN Mikro Elektronik accepts no liability for consequential or incidental
damages arising from the use of its products and reserves the right to make changes on the products herein without notice to
improve reliability, function or design. MEN Mikro Elektronik does not assume any liability arising out of the application or
use of the products described in this document.
Copyright © 2008 MEN Mikro Elektronik GmbH. All rights reserved.
Please recycle
Germany
MEN Mikro Elektronik GmbH
Neuwieder Straße 5-7
90411 Nuremberg
Phone +49-911-99 33 5-0
Fax +49-911-99 33 5-901
E-mail [email protected]
www.men.de
France
MEN Mikro Elektronik SA
18, rue René Cassin
ZA de la Châtelaine
74240 Gaillard
Phone +33 (0) 450-955-312
Fax +33 (0) 450-955-211
E-mail info@men-france.fr
www.men-france.fr
USA
MEN Micro, Inc.
24 North Main Street
Ambler, PA 19002
Phone (215) 542-9575
Fax (215) 542-9577
E-mail [email protected]
www.menmicro.com
Contents
MEN Mikro Elektronik GmbH 10
20F600-00 E2 – 2008-03-03
Contents
1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.1 Maps of the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.2 Configuring the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.3 Integrating the Board into a System . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4 Installing Driver Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 Board-to-Board Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.1 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.3 UART Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.3.1 Connection via 10-pin SA-Adapter Connectors . . . . . . . . . . 22
2.3.2 Connection via 10-pin Ribbon-Cable Connectors . . . . . . . . 25
2.4 Serial IDE (SATA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.4.1 On-Board Hard-Disk Connector (SATA1) . . . . . . . . . . . . . . 27
2.4.2 On-Board Connector for External Device (SATA0) . . . . . . . 31
2.5 CompactPCI J1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.1 Literature and Web Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.1.1 SATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.2 Finding out the Board’s Article Number, Revision and Serial Number33
Indice
Altri manuali MEN Hardware per computer
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
