messaoa NDR721 Manuale utente
Indoor IR Dome Network Camera
Quick Start
Guide
201409 721 A1
NDR721
1
English
1 Product Overview
1.1 Physical Description & Connection
Connections
Product Side ViewProduct Front View
DC Power
LAN
Lens
IR LED
Slide lock
Cable side cover
A
B
B
A
1. Identify the type of network device.
2. If the network device supports PoE (Power over Ethernet) function, simply connect the camera to it via Ethernet cable.
3. If not, both Ethernet cable and DC adaptor should connect to device
2
English
2 Installation
2.1 Package Content
2.2 Installation
2.2.1 Mounting the Camera
The Camera Ceiling Mount Installation Pack
Quick Installation Guide
Screws & Anchors Alignment Sticker
Lens adjustment tool
AB
C D
1. Place the alignment sticker on the ceiling which was preferred and drill three holes into the ceiling for cable and screws
2. Connect and route Ethernet cable or DC cable through the ceiling
(Note: remove the cable side cover once the cable route from the side)
3. Attach the camera to the ceiling by two screws.
(Note: The torque of electric screwdriver is recommended less than 6kgf-cm.)
4. Place the cover into the camera and ensured it locked.
Lens direction indicator
321 4
Indoor IR Dome Network Camera
Quick Start
Guide
201409 721 A1
NDR721
3
English
2.2.2 Tuning the Camera
1. Push the slide lock rightward to remove the dome cover
2. Adjust tilt angle by turning tilt adjustment screws
3. Fit the lens adjustment tool to lens and tune up focus by adjustment tool
4. Place the dome cover into camera module and ensured it locked
Rotate
Tilt adjustment screw
Focus
3
2
14
3 Connection
3.1 Assigning IP Address
2. Check the checkbox to select a camera device from the list.
3. The IP Camera may be assigned with a valid IP address via DHCP server. It can be also manually given a static IP address.
To do so, click on “Set IP”, and then input the IP, Subnet Mask and Gateway. Input account info if the camera is password
protected. (Default ID/Password : admin/1234)
4. Click on the “Browse” button to get access to the camera web page immediately.
1. Launch Discovery Tool (IPCAMDiscovery.exe). The tool will start searching and then displaying the cameras on the
Device List after they are found.
30
admin
4
English
3.2 Accessing the Camera
2. The live video of the camera can be played with a RTSP player, such as VLC or QuickTime. The network URL is rtsp://
Camera IP/stream1. The example given below is that live video is displayed with QuickTime player.
1. Launch IE browser and input the IP address of the camera, or click on “Browse” button on Discovery Tool.The web page
with video will then be shown as below.
3.3 Wireless Setting
3.3.1 Manual Setup
Note USB WiFi Dongle as optional parts for WiFi function
4. Once the setting complete, disconnect the Ethernet cable and then reboot the camera.
3. Type in the SSID and shared key same as what set on your router/AP and click the save button.
1. If the network device supports PoE function, simply connect the camera to it via Ethernet cable.
Otherwise both Ethernet cable and DC cable should connect to device.
2. Enter the web page setup > Network > Wireless
Choose the AP which want to be connected and click the “Select”
5
English
3.3.2 WiFi Direct Mode for mobile device
2. Scan the camera AP from smart phone/tablet WiFi Setup menu and link to the camera WiFi AP.
1. Press WiFi Mode button on camera over 1 sec but less than 3 sec, Amber LED turns on. The camera will act as a WiFi AP at
meantime.
3. Access the camera web page http://192.168.1.1/mobile by browser or scan the QR code as below Enter to “WiFi setting”
to type in the SSID and shared key same as what set on your WiFi router/AP and click the save button
4. The camera WiFi will switch back to client mode and link with the congured WiFi router/AP automatically.
6
English
3.3.3 WPS Function
WPS
1. Press the WPS (WiFi Protected Setup) button on your WiFi router/AP to trigger connection function
2. Press WiFi mode button on camera over 3 seconds then LED1 and LED2 starts to ash (the Amber LED and Green LED
start to ashing every 1 second which only last 2 minutes)
3. Once successful connection or WPS function timeout (2 minutes), the LED2 (Green) keeps steady on
7
简体中文
1 产品概述
1.1 产品特征 & 接线
接线
侧视图前视图
DC 电源
LAN
镜头
红外灯
滑锁
穿线孔侧盖
A
B
B
A
1. 确定选用的网络设备的类型；
2. 如果网络设备支持 PoE ( 以太网供电 ) 功能，只需使用一根网线连接摄像机和该网络设备；
3. 如不支持 PoE，请使用 DC 电源线连接网路设备。
8
简体中文
2 安装摄像机
2.1 标准配备
2.2 安装步骤
2.2.1 摄像机机身安装
摄像机 天花板安装配件
快速安装指南
螺丝 & 壁虎 安装模板贴纸
镜头调节工具
AB
C D
1. 安装模板贴纸粘贴到安装位置，根据贴纸上的安装孔位置钻孔；
2. 网线或 DC 电源适配器接线穿过天花板上接线孔；
( 注意：取下摄像机机身上的穿线孔侧盖便于接线 )
3. 用两个螺丝将摄像机固定到天花板上；
( 注意：建议使用扭矩小于 6kgf-cm 的电动起子 )
4. 安装并固定摄像机外壳。
镜头方向指示
321 4
室内红外网络半球摄像机
快速安装指南
201409 721 A1
NDR721
9
简体中文
2.2.2 调节摄像机
1. 如图所示，向右滑动滑锁，取下半球外壳；
2. 旋转倾斜调节螺丝，调节镜头倾斜角度；
3. 将镜头调节工具固定到摄像机镜头上，调节镜头对焦；
4. 将半球外壳安装回摄像机机身，并拧紧固定。
旋转
倾斜调节螺丝
对焦
3
2
14
3 连接摄像机
3.1 分配 IP 地址
2. 从列表中选择摄像机，勾选对应的复选框。
3. DHCP 服务器可以自动为网络摄像机分配一个有效的 IP 地址，用户也可以手动设置一个静态 IP 地址。
手动设置 IP 地址时，点击“Set IP”, 然后输入 IP 地址、子网掩码和网关。如果摄像机设置了密码保护，请输入对
应的帐号。( 默认帐号和密码为：admin/1234)
4. 点击“Browse”按钮， 登录摄像机网页界面。
1. 打开 Discovery Tool (IPCAMDiscovery.exe)，自动搜索并在 Device List 中显示搜索到的摄像机。
admin
30
Indice
Lingue:
