Messoa NCB855E Manuale utente

www.messoa.com

Fixed Network Camera

NCB855E/NCB855PRO/NCB858

Quick Start Guide

Guia de inicio rápido

Guida rapida

Guide de démarrage rapide

Краткое руководство

クイックスタートガイド

快速安裝指南

快速安装指南

ZEIM-4000813G 2012-09 A1

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 1

English

Safety Instructions

Make sure the supplied voltage meets the power consumption

requirements of the camera before powering the camera on.

Incorrect voltage may cause damage to the camera.

The camera should be protected from water and moisture,

excessive heat, direct sunlight and cold.

This installation should be made by a qualied service person and

should conform to all local codes.

Unplug the camera during lightning storms or when unused for

long periods of time.

No part of this document may be reproduced or transmitted in any form

or by any means, electronic or mechanical, for any purpose, without

the express written permission of MESSOA.

Disclaimer

Specications and information contained in this document are

presented as accurately as possible as of the time of release, but

are not guaranteed to be entirely free of error. MESSOA assumes no

responsibility for errors or omissions that may appear in this document

and reserves the right to change this publication at any time without

obligation to notify anyone of such revisions or changes.

2 NCB855E/NCB855PRO/NCB858 l Quick Start Guide

Compliance

This equipment complies with the requirements as listed below:

FCC Part 15 Class B

CE: 2004/108/EC-Electromagnetic Compatibility (EMC) directive of

EN55022, EN61000-3-2, EN61000-3-3 and EN50130-4.

WEEE

Waste Electrical and Electronic Equipment

Correct disposal of this product (applicable in the European

Union and other European countries with separate collection

systems). This product should be disposed of, at the end of

its useful life, as per applicable local lows, regulations and

procedures.

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 3

English

1. Introduction

Package Contents

Fixed Network Camera x1

CD-ROM (User manual and IP Finder utility) x1

Quick Start Guide x1

2-pin Screw Terminal Block x1

6-pin Screw Terminal Block x1

CS-C Mount Adapter Ring x1

Hardware Overview

Part Names









1. Lens mounting ring: For mounting a CS-mount or C-mount lens.

2. Back Focus Control: Allows to adjust the distance between the

back ange of the lens mounting and the image sensor.

3. Auto Iris control: Supplies power and control signals to an auto-

iris lens.

4. Tripod screw hole: Use these screw holes to attach a tripod

mount. You can attach the mount to either the top or bottom side.

(screw: 1/4”).

4 NCB855E/NCB855PRO/NCB858 l Quick Start Guide

Rear Panel

Micro

Card Audio Out Audio In

Reset

Power

Video

DC 12V

AC 24V

Ethernet/PoE

1 2 3 4 5 6

RS485+

GND

ALM-In 1

ALM-In 2

RS485

ALM-Out















1. DC 12V/AC 24V: Connect the power terminals to a power supply.

If using DC 12V power supply, make sure to connect the power

connector to correct polarities (Red+/White–).

If you plan to use power via an Ethernet connection, this connector

is not used.

2. Video: To perform focus and iris adjustments during the

installation, connect the camera to a monitor.

3. Power LED: The LED lights on when power is applied.

4. Audio In: Connects to an external microphone

5. Reset: Using a pointed object, hold down the reset button no

more than 5 seconds to restart the camera. Or hold down the reset

button for longer than 5 seconds to reset the camera to the factory

defaults.

6. Audio Out: Connects to a speaker.

7. Memory Card Slot: Insert a microSD/SDHC card to the slot for

recording and storage.

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 5

English

8. I/O: Connect your external devices, e.g., sensors and alarms to

the corresponding I/O terminal block. The pins of the I/O terminal

block controls the following signals:

Pin Signal Connection

1 RS485+ Reserved.

2 RS485- Reserved.

3 GND Ground (electricity) in electrical circuits.

4 ALM-Out Connect to device that responds to alarm

signals.

5 ALM-IN 1 Connect to device that triggers alarm signals.

6 ALM-IN 2 Connect to device that triggers alarm signals.

9. Ethernet/PoE: Connects to the LAN port of a standard

10BaseT/100BaseTX device, e.g., hub, switch or router.

6 NCB855E/NCB855PRO/NCB858 l Quick Start Guide

Dimensions

114mm (4.5”) 66mm (2.6”)

56mm(2.2”)

65mm(2.6”)

Micro

Card Audio Out Audio In

Reset

Power

Video

DC 12V

AC 24V

Ethernet/PoE

1 2 3 4 5 6

RS485+

GND

ALM-Out

ALM-In 1

ALM-In 2

RS485

2. Installation

1. Installing the Lens

Attache your lens onto the camera’s lens mounting ring.

CS-Mount lens: Attach the lens to the camera directly.

C-Mount lens: You must mount the supplied CS-C mount adapter

ring rst and then attach the C-Mount lens.

If you are using an auto-iris lens, connect the auto-iris cable to the

IRIS control connector on the camera.

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 7

English

2. Mounting the Camera

Mount the camera to your intended location. Be sure to rmly attach

the camera to a suitable at surface.

3. Connecting the Cables

1. Optionally connect external input/output devices to the camera.

2. Optionally connect a speaker and microphone to the camera.

3. Connect the camera to a power source, using one of these options:

• DC 12V or AC 24V: Connects to the power terminals on the

rear panel. If using DC 12V power supply, make sure to connect

to correct polarities (Red+/White–).

• PoE: Using a Cat. 5/5e or above UTP/STP cable, connect the

LAN port to an IEEE 802.3af compliant network device. Power

will be supplied through the Ethernet cable.

4. Optionally connect a video monitor if you want to perform focus

and iris adjustments during the installation.

4. Adjusting the View and Focus

Adjust the focus controller, and zoom controller of the lens to get the

best resolution. If needed, adjust the back focus to achieve the focus.

8 NCB855E/NCB855PRO/NCB858 l Quick Start Guide

5. Connecting to a PC for Initial Conguration

Before connecting the camera to your network infrastructure, it’s

suggested that you connect the camera to a computer rst to perform

initial congurations.

1. Configure the computer’s IP address that must be on the same

network segment with the camera’s default IP address, such as:

• IP Address: 192.168.1.100

• Subnet Mask: 255.255.255.0

2. Connect the camera via a Cat. 5/5e or above UTP/STP cable to the

computer.

The LAN port of the camera supports auto MDI/MDIX so there is no

need to use a cross-over cable.

3. On the PC, launch a web browser and enter the IP address of the

camera in the URL eld:

http://192.168.1.30

4. When prompted for login, enter the default user name: admin and

password: 1234 to log in. Note that the user name and password

are case-sensitive.

5. Configure the settings to meet your requirements. For more

information, refer to the User Manual on the provided CD.

6. Connecting to Your Network

Connecting to a LAN

If you have multiple cameras installed on your network, you can

use the provided IP Finder utility to manage the cameras. For more

information, refer to the User Manual on the provided CD.

Altri manuali per NCB855E

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Messoa Telecamera di sicurezza

Messoa

Messoa NDR891 Manuale utente

Messoa

Messoa NDF821 Manuale utente

Messoa

Messoa LPR606 Manuale utente

Messoa

Messoa PTZ900 Manuale utente

Messoa

Messoa A101RZ Manuale utente

Messoa

Messoa NDR891(H) Manuale utente

Messoa

Messoa NIC990 Manuale utente

Messoa

Messoa SCB290-HN5 Manuale utente

Messoa

Messoa NIC830-HN5 Manuale utente

Messoa

Messoa NCB750 Manuale utente

Messoa

Messoa NCB752 Manuale utente

Messoa

Messoa NCC700 Manuale utente

Messoa

Messoa NDR890-HN5 Manuale utente

Messoa

Messoa SDF418 Manuale utente

Messoa

Messoa SCR515PRO Manuale utente

Messoa

Messoa LPR610 Manuale utente

Messoa

Messoa UFD301 Manuale utente

Messoa

Messoa SPD982 Manuale utente

Messoa

Messoa SCB280 Manuale utente

Messoa

Messoa SCR368-HN5 Manuale utente

Messoa

Messoa NDZ760 Manuale utente

Messoa

Messoa NDF831-HN5 Manuale utente

Messoa

Messoa NDR891PRO Manuale utente

Messoa

Messoa NDR891(H) Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente