Metra Electronics MPS-DPSL-BT Manuale utente

MPS-DPSL-BT
INSTALLATION INSTRUCTIONS
MetraPowerSports.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 9/24/20 INSTMPS-DPSL-BT
Google Play Store Apple App Store
iOS 12.1 or higher
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties • Multimeter
TABLE OF CONTENTS
Preface ....................................................................2
Installing bluetooth board ....................................3
Pinout .....................................................................4
Installation .............................................................5
Stand-alone bluetooth diagram ..........................6
Quick setup guide ..............................................7-12
Advanced DSP features & control options .....13-14
Other installation options ....................................15
Specifications ....................................................... 16
Marine & Powersports Bluetooth Streaming
Audio Interface w/ DSP Controls
No Source Needed.
• 15 Band graphic EQ
• Bluetooth streaming from your smart device
• 4 inputs and 6 outputs, including front, rear, and subwoofer
• Independent equalization for front, rear, and sub
• Independent crossover for front, rear, and sub
• Selectable slope (12, 24, 36, or 48db per octave)
• Front and rear channels can be delayed independently up to 10ms
• Water resistant enclosure with zip tie mounts included
• Clipping detection and limiting circuits
• Bluetooth interface module included
• Volume knob & Bass knob included
•
Settings adjusted via Bluetooth® in a smart device application (tablet
or mobile phone), compatible with both Android and Apple devices
• Read, write, and store configurations for future recall
• Password protect feature available in the mobile app
• Micro-B USB updatable
• MPS-DSPL-BT circuit board
• Bluetooth streaming audio circuit board
• Volume and Subwoofer knobs
• MPS-DPSL-BT harness (16-pin & 20-pin, with gaskets)
• MPS-DPSL-BT enclosure
• Case
• Cap (with O-ring)

2
PREFACE
The MPS-DSPL-BT is designed for UTV, Marine and Motorcycle applications when a source is not required. The interface includes the AXDSPL-BT Bluetooth Streaming circuit board. This
board plugs directly into the DSP’s circuit board and will allow your phone or tablet to stream music directly to your aftermarket amplifiers. The MPS-DSP-BT is housed in a water tight
case making it perfect for ON/OFF road vehicles that are exposed to the elements. We recommend matching the MPS-DSPL-BT with our MPS-RZKIT for 2014-2020 Polaris RZR.
The MPS-DSPL-BT provides 6 outputs that are assignable to match your systems requirements. Outputs are commonly assigned as Front, Rear, and Subwoofer, which are all setup
through the free Axxess AX-DSP-XL application. Included with interface are two separate knobs that are used as an overall system volume control and a subwoofer’s volume control.
The interface provides a 12-volt 1-amp output to turn on aftermarket amp(s). If installing multiple amps, an SPDT automotive relay will be required if the amp turn-on current of all
amps combined exceeds 1-amp. Use Metra part number E-123 (sold separately) for best results.

3
REV. 9/24/2020 INSTMPS-DPSL-BT
INSTALLING BLUETOOTH BOARD
16-Pin Header
AX-DSPL-BT
AX-DSPL-BT
• The AXDSPL-BT Bluetooth interface will be used for adding a Bluetooth interface to the
MPS-DPSL-BT for playing music from your smart device.
• While playing music the volume can be controlled from your streaming device or from
the included volume knob.
1. Important! Make sure the 16 pin and 20 pin plugs are disconnected from the
circuit board before installing the ASDSPL-BT.
2. Locate the 16-pin header on the circuit board.
3. Important! Referencing how the Bluetooth interface is laid out in the picture,
carefully line up the header pins to the AXDSPL-BT Bluetooth interface. Gently
press down to secure.
Volume Knob Installation:
• Connect the Brown wire (Volume Control Wire) from the MPS-DPSL-BT harness, to the
Orange wire from the volume knob you want controlling the overall volume of your
system. The black wire from your volume control will need to be grounded. Tapping
into the ground wire from the MPS-DSPL-BT harness is recommended.
Subwoofer Knob installation
• Connect the Orange wire from the MPS-DSPL-BT harness, to the Orange wire from
the bass knob. The black wire from your volume control will need to be grounded.
Tapping into the ground wire from the MPS-DSPL-BT harness is recommended.

4
PINOUT
Input 6 - N/A Black - Chassis Ground
Input 5 - N/A Pink - N/A
Purple RCA Jack - Not Required Blue/Pink - N/A
Green RCA Jack - Not Required
Brown - Control Wire for BT Volume Knob
Gray RCA Jack - Not Required Orange - Control Wire for Bass Knob
White RCA Jack - Not Required Red - Accessory Power
Black/Yellow - N/A Yellow - Battery Power
5
4
3
2
1
TBA
INPUT 6
INPUT 5
Blue/White - Amp Turn-On RCA Jack 1 - User Assignable Output
Red/White - N/A RCA Jack 2 - User Assignable Output
White/Red - N/A RCA Jack 3 - User Assignable Output
White/Green - N/A RCA Jack 4 - User Assignable Output
RCA Jack 5 - User Assignable Output
* Cut off RCA jack for speaker level input

5
REV. 9/24/2020 INSTMPS-DPSL-BT
1. Install the MPS-DPSL-BT harness and make all necessary connections but leave the
amp turn-on wire disconnected.
2. With the arrow stamped onto the cap facing upwards, push the 16-pin connector from
the MPS-DPSL-BT harness harness into the left side of the cap. The locking clip on the
connector should face upward. Make sure the gasket is seating properly in the cap.
(Figure A)
3. With the arrow stamped onto the cap still facing upwards, push the 20-pin connector
from the MPS-DPSL-BT harness into the right side of the cap. The locking clip on the
connector should face upward. Make sure the gasket is seating properly in the cap.
(Figure A)
4. Plug the 16-pin and 20-pin connectors from the MPS-DPSL-BT harness into the
circuit board. (Figure A)
5. Slide the assembly into the case, then click it shut. Zip-tie the enclosure to a secure
location. Make sure the harnesses are pointing down to ensure that no outside
elements can enter the enclosure.
I N S TALL ATI O N
Cap (with O-ring)
Case
MPS-DSPL-BT
Circuit Board
AXDSP L
Harness
16-Pin 20-Pin
Gasket
Zip-tie Mounts
(Figure A)

6
STAND-ALONE BLUETOOTH DIAGRAM
Do Not Connect
Any remaining wires
tape off and disregard
Blue/White - Amp Turn-On Wire
INPUT 5
INPUT 6
Black - Chassis Ground
Yellow - Battery Power
Red- Accessory Power
An SPDT relay, Metra part number
E-123, must be used if more than
one amplifier will be installed
5
5
4
3
2
1
RCA Jacks
(sold separately)
Black - Chassis Ground
Orange - Control Wire
Black - Chassis Ground
Brown - Control Wire
Master Volume Knob
Sub Control
Volume Control
Interface w/ BT board
Bass Knob

7
REV. 9/24/2020 INSTMPS-DPSL-BT
QUICK SETUP GUIDE
DSP Setup & Controls
The MPS-DSPL-BT uses the Axxess DSP XL application to control and setup your DSP. Only items pertaining to the MPS-DPSL-BT will be shown.
Download and install the AXDSP-XL app from the Google Play Store or Apple App Store.
Below are the quick steps to get your MPS-DSPL-BT system configured and playing.
The AXDSP-XL app is powerful and offers many features.
To find out more about these advanced feature review the Advanced features page.
Open the app then select the Bluetooth Connection tab.
With your MPS-DSPL-BT powered on, select the SCAN button. The app will start searching for available DSP’s. Once found select your device.
In the top left corner of the app you will see it change from Not Connected to Connected.
Continued on the next page
Google Play Store Apple App Store
iOS 12.1 or higher

8
From the configurations page you should first test
your system to make sure everything is connected
properly after the DSP. To test your setup select the
IDENTIFY button. This will play a chime thought
your setup to confirm your system is ready to pass
audio. (Figure 1)
Next select your VEHICLE TYPE (Figure 1)
The MPS-DSPL-BT interface will be using the
Bluetooth circuit board as the source select General
under the “Select Vehicle Type and OE Amp
Options” menu. Keep “Without OE Amp” selected.
Then select Apply. (Figure 2)
(Figure 1)
(Figure 2)
QUICK SETUP GUIDE (CONT.)
DSP Setup & Controls (Cont’d)
Continued on the next page

9
REV. 9/24/2020 INSTMPS-DPSL-BT
(Figure 3)
QUICK SETUP GUIDE (CONT.)
DSP Setup & Controls (Cont’d)
Next Select the OUTPUTS tab – This screen is where you setup your speaker’s output channels. Under the GROUP menu, select the first drop down arrow to the right of the word NONE.
Select the name from the dropdown menu that matches the location listed on the far left of the screen.
Example: #1 – Location - Left Front, under the Groups dropdown menu select Left Front. (Figure 3)
• Location - Location of speaker.
• Group - Used to join channels together for simple equalization. Example: left front woofer/midrange and left front tweeter will be considered simply left front.
The letter M denotes the speaker assigned as the master speaker.
• Invert - Will invert the phase of the speaker.
• Mute - Will mute desired channel(s) for tuning individual channels.
Continued on the next page

10
QUICK SETUP GUIDE (CONT.)
DSP Setup & Controls (Cont’d)
(Figure 4)
DSP Setup & Controls (Cont’d)
Next Screen will allow you to set your crossover points, filter type, and slope. If you would
like to pass full frequency range to your amps set all filters to High Pass and drag the slider
all the way to the left making sure the entire frequency bar is green. (Figure 4)
• Selecting High Pass and Low Pass will provide one crossover frequency adjustment.
Band Pass should only be chosen if installing just front speakers, with one dedicated
amp for the woofers/mids, a second dedicated amp for the tweeters, along with a
subwoofer.
• If you have a specific frequency you would like, select the number above the slider
and enter in your exact frequency.
• Select the desired crossover slope, 24db, 36db, or 48 db. Higher is steeper.
Continued on the next page
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Metra Electronics Accessori


















