Metra Electronics 99-7614 Manuale utente

METRA - The World’s best kits ®metraonline.com

REV. 12/9/2016 INST99-7614

Installation instructions for part 99-7614

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• A) Radio housing • B) Radio brackets (C) • C) ISO DDIN trimplate • D) (4) #8 x 3/8” Phillips screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-7552

Antenna Adapter: • 40-NI12

• Panel removal tool • Phillips screwdriver

TOOLS REQUIRED

Nissan NV 2012-2014, NV (without NAV) 2015-up,

Nissan Quest (without NAV or rear seat entertainment) 2011-2012

99-7614

Dash Disassembly

Nissan

– NV 2012-2014.................................................2-4

– NV 2015-up (without NAV) ...............................2-4

– Quest (without NAV or rear seat entertainment)

2011-2012......................................................5-6

Kit Assembly

– ISO DIN radio provision with pocket .................... 7

– ISO DDIN radio provision..................................... 7

Table of Contents

BA CD

99-7614

NV 2012-2014,

NV (without NAV) 2015-up

1. Unclip and remove the A/C vent to

the right side of the factory radio.

(Figure A)

2. Remove the (2) Phillips screws

exposed behind vent on radio trim

panel. (Figure B)

3. Unclip and remove the left A/C

vent next to the instrument display.

(Figure C)

4. Unclip the top edge of the knee

bolster panel below the steering

column and let hang. (Figure D)

Continued on the next page

(Figure A)

(Figure D)

(Figure B)

(Figure C)

Dash Disassembly

99-7614

5. Unclip the circle trim around the

key cylinder.

6. Unclip and remove the gauge

cluster trim panel. (Figure E)

7. Remove (2) Phillips screws

exposed behind the panel on the

left side of the radio trim panel.

(Figure F)

8. Unclip and remove the trim panel

surrounding the factory radio.

(Figure G)

9. Remove (4) Phillips screws

securing the radio. (Figure H)

(Figure F)

(Figure G)

(Figure H)

(Figure E)

Dash Disassembly (Cont)

99-7614

Dash Disassembly

(Figure B)

(Figure C)

(Figure D)

(Figure A)

Quest (without NAV or rear seat

entertainment) 2011-2012

1. Unclip and remove the panels from

the bottom left and right side of the

center console. (Figure A)

2. Remove (2) clips per side exposed

behind lower panels. (Figure B)

3. Unclip and pull center console

toward rear of vehicle.

Note: You do not have to fully

remove console. (Figure C)

4. Unclip and remove the trim panel

to the left of the shifter housing the

start/stop button. (Figure D)

5. Unclip and remove the panel on

the end of the passenger side of

the dash. (Figure E)

Continued on the next page

(Figure E)

99-7614

6. Remove (1) Phillips screw from the trim panel above

the glove box then unclip and remove the panel.

(Figure F)

7. Remove (1) Phillips screw from the cup holder panel

then unclip and remove the panel. (Figure G)

Continued on the next page

(Figure F)

(Figure G)

Dash Disassembly (Cont)

99-7614

8. Remove (2) Phillips screws from the a/c

control panel and unclip and let hang.

(Figure G)

9. Remove (2) Phillips screws from the bottom

of the radio trim panel including the vents

then unclip and remove

the panel. (Figure G)

10. Remove (4) Phillips screws securing

the radio. (Figure H)

(Figure G)

(Figure H)

Dash Disassembly (Cont)

99-7614

Kit Assembly

ISO DIN radio provision with pocket

Remove the metal “DIN” sleeve and

trim ring from the aftermarket radio

2. Secure the radio brackets to the

radio housing using the (4) 3/8”

Phillips screws provided. (Figure A)

3. Slide the radio into the bracket/

housing assembly and secure

using the screws supplied with the

radio. (Figure B)

4. Locate the factory wiring harness

and antenna connector in the dash.

Metra recommends using the

proper mating adapters from Metra

and/or AXXESS.

5. Reassemble the dash in reverse

order of disassembly.

ISO DDIN radio provision

1. Remove the brackets from the

factory radio.

2. Secure the brackets to the

aftermarket radio using the screws

supplied with the aftermarket

radio. (Figure A)

Note: 99-7614 radio brackets can

be used in place of the factory

brackets.

3. Locate the factory wiring harness

and antenna connector in the

dash. Metra recommends using

the proper mating adapters from

Metra and/or AXXESS.

4. Place the ISO DDIN trim plate on

the front of the radio. (Figure B)

5. Reassemble the dash in reverse

order of disassembly.

(Figure A) (Figure A)

(Figure B) (Figure B)

REV. 12/9/2016 INST99-7614

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certiﬁed technicians

Installation instructions for part 99-7614

IMPORTANT

If you are having difficulties with the

installation of this product, please call our

Tech Support line at 1-800-253-TECH.

Before doing so, look over the instructions a

second time, and make sure the installation

was performed exactly as the instructions

are stated. Please have the vehicle apart

and ready to perform troubleshooting steps

before calling.

METRA - The World’s best kits ®metraonline.com

REV. 12/9/2016 INST99-7614

Instrucciones de instalación para la pieza 99-7614

¡PRECAUCIÓN!

Todos los accesorios, interruptores, paneles de con-

troles de clima y especialmente las luces del indicador de las bolsas

de aire deben estar conectados antes ciclar la ignición. Además, no

quite el radio de fábrica con la llave en la posición o de encendido ni

con el vehículo funcionando.

• Provisión de radio ISO DIN con bolsillo

• Provisión de radio ISO DDIN

• A) Carcasa del radio • B) Soportes de radio (C) • C) ISO DDIN placa de moldura • D) (4) #8 x 3/8” tornillos Phillips

CARACTERÍSTICAS DEL KIT

COMPONENTES DEL KIT

CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)

Arnés de cableado: • 70-7552

Adaptador de antena: • 40-NI12

• Herramienta para quitar paneles • Destornillador Phillips

HERRAMIENTAS REQUERIDAS

Nissan NV 2012-2014, NV (sin NAV) 2015-up,

Nissan Quest (sin NAV o entretenimiento para el asiento trasero) 2011-2012

99-7614

Indice

BA CD

Desmontaje del tablero

Nissan

– NV 2012-2014.................................................2-4

– NV 2015-up (sin NAV)......................................2-4

– Quest (sin NAV o entretenimiento para el asiento

trasero) 2011-2012.........................................5-6

Ensamble del kit

– Provisión de radio ISO DIN con bolsillo................ 7

– Provisión de radio ISO DDIN................................ 7

99-7614

NV 2012-2014,

NV (sin NAV) 2015 y mas

1. Desenganche y quite la rejilla del

aire acondicionado que está a

la derecha del radio de fábrica.

(Figura A)

2. Quite los (2) tornillos Phillips que

quedan a la vista detrás de la

rejilla en el panel de moldura del

radio. (Figura B)

3. Desenganche y quite le rejilla

del aire acondicionado que está

a la izquierda de la pantalla de

instrumentos. (Figura C)

4. Desenganche el borde de arriba

del panel del refuerzo para

rodillas de abajo de la columna

de dirección y déjelo colgando.

(Figura D)

Continua en la siguiente pagina

(Figura A)

(Figura D)

(Figura B)

(Figura C)

Desmontaje del tablero

Indice

Lingue:

Altri manuali Metra Electronics Supporto TV

Metra Electronics

Metra Electronics 95-8910S Manuale utente

Metra Electronics

Metra Electronics 99-5831 Manuale utente

Metra Electronics

Metra Electronics DP-7363B Manuale utente

Metra Electronics

Metra Electronics 95-3005 Manuale utente

Metra Electronics

Metra Electronics 99-5830B Manuale utente

Metra Electronics

Metra Electronics 99-3022B Manuale utente

Metra Electronics

Metra Electronics TX86 Manuale utente

Metra Electronics

Metra Electronics 99-5832G Manuale utente

Metra Electronics

Metra Electronics 107-GM3B Manuale utente

Metra Electronics

Metra Electronics 99-5600 Manuale utente

Metra Electronics

Metra Electronics 108-FD9B Manuale utente

Metra Electronics

Metra Electronics 95-7815B Istruzioni per l’uso

Metra Electronics

Metra Electronics 95-7802CH Manuale utente

Metra Electronics

Metra Electronics 95-8734 Manuale utente

Metra Electronics

Metra Electronics TL64 Manuale utente

Metra Electronics

Metra Electronics 99-9223 Manuale utente

Metra Electronics

Metra Electronics 99-7367 Manuale utente

Manuali Supporto TV popolari di altre marche

Ergotron

Ergotron Neo Flex Cantilever UHD Manuale utente

StarTech.com

StarTech.com FPCEILBTB Manuale utente

VonHaus

VonHaus 05/038 Manuale utente

Techlink

Techlink ECHO TV Manuale utente

Sandstrom

Sandstrom SSTVMC12X Manuale utente

Sony

Sony SU-WL700 Guida

ICW

ICW SCACC18 Manuale utente

LG WM-L640V Manuale utente

Gembird

Gembird WM-65ST-01 Manuale utente

ERARD

ERARD FiTUP XXL 035320 Manuale utente

PEERLESS

PEERLESS PLCK-1 Guida

Kanto

Kanto RCF180 Manuale utente

GEM

GEM GEM GP001 Manuale utente

Gladiator Joe

Gladiator Joe GJ0A0053 Manuale utente

Vivotek

Vivotek AM-105 Manuale utente

Vivo

Vivo VESA STAND-VAD1B Manuale utente

AmazonBasics

AmazonBasics B07QG3LMG4 Manuale utente

Secura

Secura QLF210 Manuale utente