Metrologic MS951 Manuale utente

METROLOGIC INSTRUMENTS, INC.

MS951 Hand-Held Laser Scanner

and MS951 Hand-Held Scanner

with Built-in PC

Keyboard Wedge Interface

Installation and User’s Guide

MLPN 2365

Printed in USA

October 1998

Locations:

USA Corporate Headquarters Europe

Metrologic Instruments, Inc. Metrologic Instruments GmbH

90 Coles Road Dornierstrasse 2

Blackwood, NJ 08012 82178 Puchheim b.

Customer Service: 1-800-ID-METRO Munich, Germany

Tel: 609-228-8100 Tel: 49-89-89018-0

Fax: 609-228-6673 Fax: 49-89-89019-200

[email protected] [email protected]

www.metrologic.com

ASIA

South America Metrologic Asia (PTE) Ltd.

Metrologic Instruments 31, Kaki Bukit Road 3

Rua Flórida, 1.821-5°Andar-Brooklin #05-08 Techlink

CEP 04571-090, São Paulo-SP, Brasil Singapore 417818

Outside Brazil: Tel: 65-842-7155

Tel: 55-11-5505-6568 Fax: 65-842-7166

Fax: 55-11-5505-1681 [email protected]

[email protected]

In Brazil:

Tel: 55-11-5505-2396

Fax: 55-11-5507-2301

[email protected]

be reproduced, transmitted, or stored in any form or by any means without prior written

consent, except by reviewer, who may quote brief passages in a review, or provided for

in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of their

respective companies.

iii

Table of Contents

Introduction ................................................. 1, 2

Scanner and Accessories ......................................... 3

Quick Start .................................................... 4

Operational Test ............................................... 5

Scanner Installation: Powered by External Power Supply ............... 6

Scanner Installation: Powered by Host Device ....................... 7

Scanner Installation to the PC

(Scanner with Built-in PC Keyboard Wedge Interface) ............... 8, 9

Configuration of the MS951/MS961-48 Scanner ..................... 10

Version “11" 46X Interface ...................................... 11

Configuring the Scanner with 46XX Interface ................ 12

Operating Characteristics ................................ 12

Configuring the IBM 46XX .............................. 12

IBM 4683 and 4693 Terminals Driven by a 46XX Store Controller

Running 4680.OS or 4690.OS ............................ 13

IBM 4684 and 4694 Systems ............................. 13

Parts of the MS951 ............................................ 14

Components of the MS900 Series Stand ............................ 15

Installation of the MS900 Series Stand .......................... 15, 16

Audible Indicators ............................................. 17

Visual Indicators ........................................... 18-21

Labels ....................................................... 22

IR Sensor Activation ........................................... 23

Scan Field ................................................... 24

MS951 - Depth of Field and Symbol Specification ................ 25, 26

MS961 - Depth of Field and Symbol Specification ................ 27, 28

Maintenance .................................................. 29

Applications and Protocols ...................................... 29

Appendix A

MS951 Hand-Held Laser Scanner Specifications .......... 30, 31

MS951 Hand-Held Laser Scanner w/KBW Specifications ... 32, 33

Appendix B

Default Settings ..................................... 34-38

Appendix C

Pin Assignments for the Coil Cable ........................ 39

Pin Assignments for the MCA (DEC9S) .................... 40

Pin Assignments for the 5-pin DIN and 6-pin DIN (KBW) ..... 41

Appendix D

Warranty and Disclaimer ............................. 42, 43

Appendix E

Notices ........................................... 44, 45

Appendix F

Patents ............................................... 46

Index .................................................... 47, 48

Introduction

The scanning process is initiated by an infrared device (ScanQuest™ Sensor)

that is active as long as power is applied to the unit. The infrared (IR) signal

extends approximately eight (8) inches beyond the scan window in long range

mode. In short range mode it extends approximately three (3) inches beyond

the scan window. To activate the unit, wave an object in front of the IR sensor

or pick up the scanner and direct the scan window down-wards.

When the unit is activated by the IR sensor, the red LED will remain on. This

is a visual indication that the laser is on and the scanner is beginning a

sequence of bar code recognition, decoding, and transmission. When an object

is in the scan field, the laser determines if a bar code is present. If a bar code is

not detected within approximately 2.5 seconds, the red LED will shut off

indicating that the laser is no longer on. To reactivate the scanning sequence,

the object must be removed and another object must be presented.

When a bar code is recognized, the scanner will decode the bar code and then

transmit the data to the host system. When this occurs, the green LED will

flash and the scanner will beep when the decoding is complete. At this time,

the laser will turn off if the object is removed from the field. However, if the

object stays in the field the laser remains on for up to 2.5 seconds trying to

detect another bar code. This feature allows very fast consecutive scans of

symbols in close proximity, such as a wall of boxes or cartons, or a bar coded

menu. The laser will stay on for approximately 4 seconds and then will turn off

if the same symbol stays in the field after a successful scan. This prevents

unintentional reads of the same bar code. To read the same symbol more than

once, simply remove the object from the scan field for approximately 1 second

and then the scanner can then scan the same symbol on the next pass.

The MS951 Hand-Held Laser Scanner with Built-in PC Keyboard Wedge

Interface is designed to be used for keyboard emulation only. However, many

RS-232 programmable functions that are available in other Metrologic

scanners are also available as keyboard wedge functions. The most important

selectable options specific to the keyboard wedge are the following:

Keyboard Type

!** AT (includes IBM PS2 models 50, 55, 60, 80)

!XT

!IBM PS2 (includes models 30, 70, 8556)

Keyboard Country Type

!** USA !United Kingdom

!French !German

!Italian !Spanish

!Belgium !Swiss

!IBM KB4700 Financial Keyboard

** Default setting. Refer to the Programming Guide MLPN 2366 for

information on how to change the default settings.

Scanner and Accessories

The following is a list of the parts included in the MS951 shipping

carton.

!MS951 Hand-Held Laser Scanner - Refer to page 28 for

available communication protocols

!Stand (MLPN 45482)

!Optional Power Transformer 120V or 220V or 240V (AC in)

5V (DC out) @300mA regulated (MLPN 46010/46009/46008)

for applications where host power is not available

!Installation and User’s Guide (MLPN2365)

!MS951 Hand-Held Laser Scanner including all

Scanner Configurations Programming Guide

(MLPN 2366)

Keyboard Wedge Scanners:

!Adaptor Cable with a 5-pin DIN male connector on one

end and a 6-pin mini DIN female connector on the other

(MLPN 19716)

RS-232, Light Pen, some OCIA and some 46xx scanners:

!MCA (Metrologic Connector Adaptor) (MLPN MCA951)

!For direct connect application (No Power Transformer)

4 position MCA ground jumper (MLPN 51191)

!RS-232 Scanner Demonstration Program (Receive)

diskette (MLPN 2351)

Other items may be ordered for the specific protocol being used. To order

additional items, contact the dealer, distributor or call Metrologic’s

Customer Service Department at 1-800-ID-METRO or 1-800-436-3876.

Quick Start

1.) Plug in the scanner. When the MS951 is ready to

scan, the red LED will turn on, followed by the

green LED, and then the scanner will emit one

beep.

2.) The scanner is shipped from the factory pro-

grammed with default settings. To configure

the MS951 scanner to meet the host system’s

specific needs, refer to the Programming

Guide (MLPN 2366) for instructions on how

to enter the program mode and to select the

appropriate bar codes.

Note: Keyboard Wedge scanners default to Keyboard Wedge

Communications and USA, AT keyboard when the Recall

Defaults is scanned. With all other versions, the Recalll Defaults

barcode configures the MS951 for an RS-232 interface. If RS-232

is not being used, scan at least one other bar code to enable OCIA,

Light Pen or 46xx.

Operational Test

If the scanner is to receive power from an external power supply, test the

scanner before it is connected to the host system.

Keyboard Wedge Scanners:

1. Plug one end of the coil cable into the keyboard connector on the PC.

Then plug the keyboard connector into the other end of the coil cable.

Plug in the external transformer.

2. Check the AC input requirements of the power supply (for special

circumstances only) to make sure the voltage matches the AC outlet.

Connect AC power to the transformer.

3. Listen for a single beep (red LED on) which indicates the scanner is

ready for use.

RS-232, Light Pen, OCIA and 46xx scanners:

1. Plug the scanner’s coil cable into the MCA (Metrologic Connector

Adaptor).

2. Check the AC input requirements of the power supply to make sure the

voltage matches the AC outlet. Plug the power supply into the MCA and

the appropriate AC outlet. (the socket-outlet shall be installed near the

equipment and shall be easily accessible.)

3. Listen for a single beep (red LED on) which indicates the scanner is

ready for use.

MCA

Female

9-pin D

10 Position Modular Connector

at the end of the Coil Cable

Scanner Installation: Powered by External Power Supply

To maintain compliance with applicable standards, all circuits connected to the

scanner must meet the requirements for SELV (Safety Extra Low Voltage)

according to EN 60950.

1. Turn off the host system.

2. If using a communication cable, connect the cable to the correct port on

the host device and the MCA (Metrologic Connector Adaptor). If the

host device is an IBM compatible PC with a male 9-pin serial port,

connect the MCA to the port.

3. Plug the scanner’s coil cable into the MCA.

4. Check the AC input requirements of the power supply to make sure the

voltage matches the AC outlet. (the socket-outlet shall be installed near

the equipment and shall be easily accessible.) Plug the power supply

into the MCA and the AC outlet.

5. Turn on the host system.

Note: a. When the scanner first receives power, the red LED will turn

on, followed by the green LED, and then the scanner will beep

once.

b. Plugging the scanner into the serial port of the PC does not

guarantee that scanned information will appear at the PC. A

software driver and correct configuration setting are also

required for proper communication to occur.

Altri manuali per MS951

Indice

Altri manuali Metrologic Scanner

Metrologic

Metrologic MS9500 Voyager Series Manuale utente

Metrologic

Metrologic Orbit MS7120-38 Manuale utente

Metrologic

Metrologic MS6720 Istruzioni utente

Metrologic

Metrologic MS9524 VoyagerPDF Series Manuale utente

Metrologic

Metrologic IS4225 ScanGlove Manuale utente

Metrologic

Metrologic MS9540-38-3 - Metrologic MS9540 VoyagerCG Manuale utente

Metrologic

Metrologic Laser Scanner Manuale utente

Metrologic

Metrologic IS4220 ScanGlove Istruzioni per l'installazione e il funzionamento

Metrologic

Metrologic MS9500 Voyager Series Manuale utente

Metrologic

Metrologic IS4813 Guida rapida alla configurazione

Metrologic

Metrologic FocusBT MS9535 Manuale utente

Metrologic

Metrologic MS9590i VoyagerGS Series Manuale utente

Metrologic

Metrologic Eclipse MS5145-00 Manuale utente

Metrologic

Metrologic MK9535-39B538 Manuale utente

Metrologic

Metrologic MS9535 VoyagerBTSeries Manuale utente

Metrologic

Metrologic MS9524 VoyagerPDF Series Manuale utente

Metrologic

Metrologic iQ160 Guida utente

Metrologic

Metrologic MK9535-39B538 Manuale utente

Metrologic

Metrologic OrbitCG MS7180 Manuale utente

Metrologic

Metrologic MS951 Istruzioni operative

Metrologic

Metrologic IS4320 ScanGlove Istruzioni operative

Metrologic

Metrologic MK2320KD-60B241 - Metrologic MS 2320 Stratos... Manuale utente

Metrologic

Metrologic MS9544 VoyagerPDF Series Manuale utente

Metrologic

Metrologic ARGUSSCAN MS7220 Manuale utente

Manuali Scanner popolari di altre marche

Plustek

Plustek Scanner Manuale utente

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuale utente

Renkforce

Renkforce DS100-5M Manuale utente

Image Access

Image Access WideTEK A2 Manuale utente

Canon

Canon imageFORMULA CR-120N Manuale utente

Fujitsu

Fujitsu FI-4860C2 Manuale utente

GeoSlam

GeoSlam ZEB Horizon Istruzioni per l'installazione

Kodak

Kodak i5800 Scanner Manuale utente

Kodak

Kodak i7300 Manuale utente

Revopoint

Revopoint POP Manuale utente

Fujitsu

Fujitsu fi-4860C Manuale utente

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuale utente

Faselase

Faselase F6 Manuale utente

Fujitsu

Fujitsu CardMinder Manuale utente

Uniden

Uniden BC340CRS Manuale utente

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuale utente

Mustek

Mustek PageExpress 4800 Pro Manuale utente

Optex

Optex 750830 Manuale utente