MF DIGITAL DIRECTOR EC Manuale utente

Director EC Office Publisher with OptiEC

Printer Installation Guide

Document Revision: 2/21

DIRECTOR EC OFFICE PUBLISHER WITH OptiEC PRINTER

INSTALLATION GUIDE

DIRECTOR EC OFFICE PUBLISHER -- PC MINIMUM REQUIREMENTS

•A Pentium® III or compatible personal computer @ 933 MHz or faster with Three (3) Free PCI slots.

•Windows 2000 Professional (service pack 4.0 or higher) or Windows XP (service pack 1.0a or higher)

•1GB RAM (PC 133 specification - SDRAM or DDRAM)

•1 Hard Disk Controller Adaptec BRAND Ultra 29160

•1 18 GB SCSI 15,000rpm Ultra 160 SCSI Hard Drive (formatted NTSF) as follows:

•1 Basic Partition for System (C:) & 2 5GB NTFS Partitions (D:)(E:) – Temp folder in root on each partition

•1 Firewire 1394 Card (Supplied by MF DIGITAL)

•1 Software Identifier Card (Supplied by MF DIGITAL) Computer needs 3.5” power connector for this card

•1 external COM port (COM1 or COM2) - 2 ports needed if using Prism Plus or Spectrum2

•Network 100/10Mbs on Board

•Video 1024 x 768

•One Parallel Port

THE DIRECTOR EC LOADER MUST BE INSTALLED ON COM PORT 2

THE DIRECTOR EC SOFTWARE MUST BE INSTALLED ON C:\ DRIVE

MF DIGITAL

121 Carolyn Blvd.

Farmingdale, NY 11735

001 631 249 9393

www.mfdigital.com

Installing the Firewire Adapter & Software Identifier Cards

You should never attempt to service a unit without ensuring proper anti-static protection. The

use of a grounding strap, or other such grounding device, is advised. In addition, the internal

configuration of your computer may be different from the computer pictured below.

Note:

Installing the Firewire Card

The DirectorEC Office Publisher requires

one IEEE-1394 card.

1. Shut down the PC.

2. Turn the PC’s power off.

3. Unplug the PC.

4. Remove the PC’s cover as indicated in

the PC’s manual.

5. Locate an empty PCI slot, as seen in

(fig.1).

6. Install the firewire adapter card (fig. 2).

Installing the Software Identifier Card

1. If your PC is not OFF, perform the

Windows shutdown now.

2. Turn-off powers switch and unplug AC

power from the wall.

3. If the PC’s cover has been re-installed,

remove it now.

4. Locate an Empty slot, Mount the Software

Identifier card in slot as illustrated (fig. 3).

5. Connect the 3.5” Floppy type power cable

such that the yellow wire is facing out.

6. Using a 40 Pin EIDE cable, connect the

card to the Secondary IDE Channel on

your PC mother- board.

7. Be sure PIN 1(red wire) if facing AWAY

from the motherboard, and next to the

power connector on software identifier

card (fig. 3).

(fig. 3)

(fig. 1) (fig. 2)

Page 2

Making the Connection

PC Connection

Page 3

Installing the Director EC Office Publisher Software [1]

ote:

When installing the Director

EC software on Windows XP

you MUST install ODBC

FoxPRo drivers.

See step #2 bellow.

(fig. 1)

1. Insert the Director EC

Publisher software CD.

2. From the CD ROM drive of

the computer, click

Director 3.0

3. Click Next (fig. 1).

4. You MUST accept default

folder and click Next (fig. 2).

5. Confirm Installation and

click Next (fig. 3).

6. Installation completed click

Close (fig. 4).

(fig. 2)

(fig. 3)

(fig. 4)

Page 4

Installing the Director EC Office Publisher Software [2]

ote:

Windows XP MUST install

ODBC FoxPRo drivers before

running Director 3.0

1. After installation of the

Director EC software go to

“c:\cdDirector\ODBC FoxPro

Driver” folder. (fig. 1)

2. Double click the VFPODBC

file. (fig.2)

3. Congratulations you have

successfully installed

Director EC Office Publisher

software.

(fig. 1)

(fig. 2)

Page 5

Selecting system drives for Director EC

System Setup tab

1. Open Director EC software.

6. Director EC software might

prompt a message “System

Drives Missing” click OK.

7. Go to “System Setup” tab

and select system drives “D

and E” (fig. 1)

(fig. 1)

Page 6

Turning OFF Auto RUN on CD-ROM.

1. Go to “Start”.

2. Go to “Run”

3. Type in “regedit” then click

OK (fig.1)

4. Navigate to “Autorun”

registry following the path

“My

Computer\HKEY_LOCAL

_MACHINE\SYSTEM\Cu

rentControlset\Services\Cd

rom” (fig. 2)

5. Set value in “Autorun”

registry to zero if different.

(fig. 1)

Value in Autorun

is set to zero.

(fig. 2)

Page 7

Installing the Director EC Publisher Alignment Utility for aligning the

Drive Tower and Printer

1. Insert the Director EC Office

Publisher CD into the CD-ROM

drive of your PC.

2. Click on setup.exe of the alignment

utility and Click OK (fig. 1).

3. Click Next button to install

complete version (fig. 2).

4. Click Install to start installation

(fig. 3)

(fig. 1)

(fig. 2)

(fig. 3)

Page 8

Installing the Director EC Publisher Alignment Utility for aligning the

Drive Tower and printer (cont.)

5. A progress bar will appear (fig. 4).

6. Click Finish to finish installation.

(fig. 5)

(fig. 4)

(fig. 5)

Page 9

Installing the OptiEC Printer Driver

1. Click Start-> Settings-> Printers

2. Click Add New Printer

3. The “Welcome to the Add Printer

Wizard” window will appear (fig 1).

Click Next.

4. In the “Local or Network Printer”

window, uncheck the “Automatically

detect installed printer” option ,

leaving the “Local printer attached to

computer” option (fig 2) and click

Next..

5. In the “Select a Printer Port” window,

leave the default as LPT1 (fig 3) and

click Next.

6. In the “Install Printer Software”

window, click the “Have Disk” button

(fig 4). You will then be prompted to

“Install from Disk”, click the

“Browse” button (fig 5). Select the

location of the printer driver from

your CD-ROM drive in the PC (fig 6).

fig 3

fig 1

fig 2

fig 4

fig 5

fig 6

Page 10

Altri manuali per DIRECTOR EC

Indice

Altri manuali MF DIGITAL Duplicatore di dischi

MF DIGITAL

MF DIGITAL 5000 Platform Series Manuale utente

MF DIGITAL

MF DIGITAL DIRECTOR series Manuale di istruzioni

MF DIGITAL

MF DIGITAL DIRECTOR series Manuale

MF DIGITAL

MF DIGITAL 5500 Series Manuale

MF DIGITAL

MF DIGITAL 5907-VL Manuale utente

MF DIGITAL

MF DIGITAL EC Series Manuale utente

MF DIGITAL

MF DIGITAL 5000 Platform Series Manuale utente

MF DIGITAL

MF DIGITAL DIRECTOR EC Manuale utente

MF DIGITAL

MF DIGITAL DIRECTOR series Istruzioni per il montaggio

MF DIGITAL

MF DIGITAL SCRIBE EC Manuale

MF DIGITAL

MF DIGITAL 5907-VL Manuale

MF DIGITAL

MF DIGITAL Scribe SA Standalone Series Manuale

MF DIGITAL

MF DIGITAL DIRECTOR series Manuale

MF DIGITAL

MF DIGITAL Scribe series Manuale

MF DIGITAL

MF DIGITAL 5000 Platform Series Manuale

MF DIGITAL

MF DIGITAL Baxter 9100 Manuale utente

MF DIGITAL

MF DIGITAL Dolphin 5900 Manuale utente

MF DIGITAL

MF DIGITAL 5200 Live Series EventCD Manuale

MF DIGITAL

MF DIGITAL DIRECTOR series Manuale utente

Manuali Duplicatore di dischi popolari di altre marche

Riso

Riso CV Series Manuale

MicroBoards Technology

MicroBoards Technology GX-2 Manuale utente

Addonics Technologies

Addonics Technologies HDUS325DX Manuale utente

Carry

Carry Pro118 Manuale utente

CopyPro

CopyPro PowerPro II Manuale utente

Primera

Primera Max Manuale utente

Logicube

Logicube EchoPlus-NG Manuale utente

Silca

Silca Delta 2000 SA Manuale utente

Reflex7

Reflex7 Daisy Chain Series Manuale utente

Vinpower Digital

Vinpower Digital SharkCopier DC Manuale utente

Codonics

Codonics Virtua E Manuale utente

Octave

Octave Copy Master II Manuale utente

Kanguru

Kanguru U2-DVDDUPE-S Manuale utente

StarTech.com

StarTech.com 8STSATDUP11 Manuale utente

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Manuale utente

Addonics Technologies

Addonics Technologies UDFH7 Manuale utente

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Manuale utente

Addonics Technologies

Addonics Technologies CFASTD5 Manuale utente