MFC International Bravo 2000 Manuale utente
Product Manual
Bravo 2000 Electric Inator
2© MFC International
Technical Data
Safety Instructions
Instructions for Use
Repairs
3
4
5
6
WARNING: Carefully read this manual before operating the
Bravo 2000 Electric Inator.
NOTICE: The manufacturer takes no responsibility for the
consequences of actions not complying with the instructions
given in this manual.
Index
3
© MFC International
Technical Data
Technical Data Bravo 2000 Electric Inator
Product Code 180026
Voltage Supply 230V (Main Motor) 230V (Booster)
Max. Power 1000W / 2000W
Max. Pressure 140 mbar (2 psi) / 400 mbar (5.8 psi)
Max. Flow Rate 1200 l/min / 2000 l/min
Dimensions 32 x 17 x 26 cm
Weight 4.1 kg
The Bravo 2000 electric inator consists of a main motor and a supplementary (booster)
motor, which increases the capacity and pressure. The two motors can run simultaneously
to obtain maximum capacity and pressure.
On the Bravo 2000, you can press the orange button to just run the main motor, or you can
press the red button to switch on the booster to help obtain maximum performance. Both
motors are protected by thermal-amperic fuses.
Bravo 2000 Electric Inator Features:
• Inates and deates
• Has a robust outer steel casing for additional protection
• Fitted with main motor and a booster motor to increase capacity and pressure
• 3m integral mains power lead comes with 2 pin plug (supplied with UK 3 pin plug
adapter if needed)
• Comes with an ination hose, 7 dierent adapters and a shoulder carry strap
4© MFC International
Safety Instructions
WARNINGS
1. Before inserting the plug into the mains socket, check that the voltage corresponds
with that written on the plate.
2. It is forbidden to use the device in humid environments and/or close to water.
3. Never touch the power cable with wet hands (risk of electric shock).
4. The electrical power cable cannot be replaced, if the cable is damaged the product
cannot be used.
5. Keep the product out of the reach of children.
6. Do not leave the inator running unattended.
7. Do not use the inator with adapters other than those supplied with the product as
they could damage the device.
8. Take care not to allow foreign bodies (sand or small stones) to get into the inator.
9. Repairs should only be performed by the technical assistance service (see page 6).
10. The manufacturer is not responsible for damage caused as a result of improper use
or failure to observe the envisaged usage.
11. Long periods of use can cause overheating and damage to the product. Do not use
for more than 20 minutes continuously.
5
© MFC International
Instructions for Use
INFLATION OPERATION
1. From the white universal adaptor, select the reducer that engages and opens the
valve of the inatable structure.
2. Insert the selected adaptor on the braided joint on the end of the tube.
3. Tighten the black adaptor on to the ination side of the inator (OUT).
4. Check that both start switches are set to ( 0 ).
5. Insert the plug and set the orange switch to position ( | ). If necessary, also use the
red switch to obtain maximum performance to start the ination.
6. The inator is limited to a maximum pressure of 140 mbar (orange switch) and 350
mbar (orange+red switches).
7. When the maximum pressure is reached, switch o the inator immediately to avoid
overheating the motor.
DEFLATING OPERATION
1. From the white universal adaptor, select the reducer that engages and opens the
valve of the inatable structure.
2. Insert the selected adaptor on the braided joint on the end of the tube.
3. Fit the black adaptor on to the deation side of the inator (IN).
4. Check that both ON switches are set to ( 0 ).
5. Insert the plug and set the orange switch to position ( | ). If necessary, also use the
red switch to obtain maximum performance to start the deating.
6. When the inatable is completely deated, switch o the inator immediately to avoid
overheating the motor.
NOTE: It is advisable to check the pressure with a pressure gauge.
6© MFC International
Repairs
REPAIRS
As a general rule, repairs/damaged products will need to be assessed in two categories:
a) that which is repairable at the base, or b) serious damage that will need to be
repaired by MFC International.
If in doubt as to the extent of the damage and the level of repairs necessary,
please contact the MFC service department on +44 (0)1443 433 075.
WARNING: Repairs may only be carried out by the manufacturer, or people
certied by MFC International Ltd.
.
7
© MFC International
MFC International
Naval Yard
Tonypandy
Rhondda Cynon Ta
CF40 1JS
T. +44 (0) 1443 433 075
www.mfc-international.com
A Respirex International Limited Group Company SA-MA118-01
Questo manuale è adatto per i seguenti modelli
1
Indice
