MFJ MFJ-1024 Manuale utente

Indice

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente

MFJ-1024 REMOTE ACTIVE ANTENNA

The MFJ-1024 Remote Active Antenna is designed to provide reception of

radio signals from 50 KHz to 30 MHz using a remote mounted antenna and

amplifier module.

INSTALLATION

1. Attach the remote unit to your pole or other mounting location and

run the cable to your receiver location.

2. Connect the cable from the remote unit to the REMOTE ANTENNA jack

on the back of the base unit. The jack is a PL-259 type.

3. Connect a 12-15 VDC power supply or an MFJ 12V AC adapter

to the PWR jack on the back of the base unit. The power jack

accepts a 2.5mm subminiature plug, with the tip positive.

4. Connect your receiver or receivers to the jacks labeled

RECEIVER A and RECEIVER B on the back of the base unit. The

jacks accept RCA type plugs.

5. If desired, an auxilliary antenna may be connected to the AUX

ANT jack on the base unit.

OPERATION

After proper installation of the Remote Active Antenna, turn on your

receiver and depress the PWR ON switch on the antenna base unit. The

front panel LED should light, indicating circuit operation. Select

receiver A or B by pressing the REC A/B switch. Set the attenuation

switch to -Odb. Set the GAIN control to the 9 o'clock position.

Tune your receiver to the frequency you wish to listen to.

Increase GAIN to desired level. Best circuit operation may be

achieved at less than maximum GAIN setting. On very strong signals

that may overload your receiver, it may be necessary to set the

attenuation switch to the -20db position to reduce the signal

strength.

NOTE: On some portable receivers, especially those with plastic

cabinets, oscillation may occur at some frequencies if GAIN is set

too high. If this happens, reduce the level of the GAIN control until

oscillations disappear.

When the power switch is in the AUX position the power to the remote

antenna and amplifier module is cut off and your receiver is connected

to the auxilliary antenna jack on the base unit. Any antenna of your

choise may be connected to the jack. When the unit is in the

auxilliary mode, the GAIN control is not operational, but the

attenuation and receiver select controls will work with your auxilliary

antenna.

All manuals and user guides at all-guides.com

all-guides.com

All manuals and user guides at all-guides.com