MFZ Ovitor CS 300 RM Manuale utente

Operating Instructions for CS 300 RM Controls EN

CS 300 RM Gate Controls Rev. B 1.0 – 1

2 – CS 300 RM Gate Controls / Rev. B 1.0

1. Contents 3. General safety instructions

2. Key to symbols

Original operating instructions

−Protected by copyright.

−No part of this manual may be reproduced without our

prior approval.

−Subject to alterations in the interest of technical progress.

−All dimensions are given in millimetres.

−The diagrams in this manual are not to scale.

Guarantee

The function and safety of the equipment is only guaranteed

if the warning and safety instructions included in these opera-

ting instructions are adhered to.

MFZ Antriebe GmbH + Co. KG is not liable for personal injury

or damage to property if these occur as a result of the war-

nings and safety advice being disregarded.

Using the equipment for its intended purpose

The CS 300 RM control unit is intended exclusively for the

purpose of controlling tubular drives that have mechanical

limit switch systems.

Target group

Only qualied and properly trained electricians are allowed to

connect up, programme or service the control unit.

Qualied and trained electricians must have the following:

− Knowledge of the general and specic safety and accident-

prevention regulations

−Knowledge of the relevant electrical regulations

−Training in the use and care of appropriate safety equip-

ment

−The ability to recognise the risks associated with electricity

Instructions relating to installation and connection

−Before commencing electrical works, the system must be

disconnected from the power supply. Measures must be

taken to ensure that the power supply remains switched off

for the duration of the works.

−The local safety regulations must be observed.

−Power cables must be laid separately from control cables.

Danger of personal injury!

The safety instructions must be observed!

Warning! Danger to property!

The safety instructions must be observed!

Information

Special information

Reference to other sources of information

1. Contents 2

2. Key to symbols 2

3. General safety instructions 2

4. Overview of products 3

5. Initial operation 5

6. Programming with the LED module 10

7. Programming with the LCD monitor 12

8. Navigator (LCD monitor only) 14

9. Overview of functions 16

10. Error messages and rectication 23

11. Technical data 24

12. EC Declaration of Incorporation 25

13. Appendix 26

CS 300 RM Gate Controls / Rev. B 1.0 – 3

Regulations and test specications

The following regulations must be complied with when

connecting, programming or servicing the unit. (The list is not

exhaustive.)

Construction product standards

− EN 13241-1 (Products without re resistance or smoke

control characteristics)

−EN 12445 (Safety in use of power operated doors -

Test methods)

−EN 12453 (Safety in use of power operated doors -

Requirements)

−EN 12978 (Safety devices for power operated doors and

doors - Requirements and test methods)

EMC

−EN 55014-1 (Electromagnetic compatibility - Requirements

for household appliances)

−EN 61000-3-2 (Limits for harmonic current emissions )

− EN 61000-3-3 (Limitation of voltage changes, voltage uc-

tuations and icker in public low-voltage supply systems)

−EN 61000-6-2 (Electromagnetic compatibility (EMC) - Part

6-2: Generic standards - Immunity for industrial environ-

ments)

−EN 61000-6-3 (Electromagnetic compatibility (EMC) - Part

6-3: Generic standards - Emission standard for residential,

commercial and light-industrial environments)

Machinery Directive

−EN 60204-1 (Safety of machinery, electrical equipment of

machines, Part 1: General requirements)

−EN 12100-1 (Safety of machinery - Basic concepts, general

principles for design, Part 1: Basic terminology, methodo-

logy)

Low voltage

−EN 60335-1 (Household and similar electrical appliances -

Safety)

−EN 60335-2-103 (Particular requirements for drives for

gates, doors and windows)

Committee for Workplaces (Ausschuss für Arbeitsstätten -

ASTA)

−ASR A1.7 (Technical Regulations for workplaces - Doors

and gates)

4.1 Various options

The following package options are available for the CS 300

RM controls:

−CS 300 RM control unit with LCD monitor

−CS 300 RM control unit with LCD monitor in housing

−CS 300 RM control unit with LED module for setting the

OPEN and CLOSED door positions (no further settings are

possible).

−CS 300 RM control unit without LED module and without

LCD monitor (a module or monitor is required for adjusting

the settings)

All the above options can be tted with a plug-in weekly

timer (switch clock) and a plug-in radio receiver.

The following options are available for the housing:

−Housing unit with 3-button input unit CS

−Housing unit with 3-button input unit KDT

−Housing with ON/OFF key switch

−Housing with mains switch

−Housing with emergency off button

The operating instructions describe the connection options

and programming procedures for the following models:

−CS 300 RM control unit with LED board

−CS 300 RM control unit with attached LCD display board

4. Overview of products

4 – CS 300 RM Gate Controls / Rev. B 1.0

4. Overview of products

4.2 CS 300 RM main board

(with attached LCD display monitor)

Key:

X1: terminal block for mains

connection / motor

X3: terminal block for command

devices

X4: terminal block

safety devices / before-end

switch

X5: terminal block

relay

X6: terminals for internal ON-

OFF switch

X7: terminals for internal 3-but-

ton input unit

X8: socket for monitor

(under monitor)

X9: terminals for

radio receiver

X10: terminals for weekly timer

(switch clock)

X12: socket for external radio

receiver

X13: terminals for

CS 3-button input unit

H4: status display for safety edge

protection (SKS) – illumina-

ted when SKS is working

H6: Safety circuit status message

– lights up when the safety

circuit is closed

F1: 4A fuse

CS 300 RM Gate Controls / Rev. B 1.0 – 5

5. Initial operation

5.1 General

Warning!

To guarantee that the equipment functions

properly, the following points must be

ensured:

The door is installed and operational.

- The MFZ tubular drive is installed and ready

for operation.

- The command and safety devices are instal-

led and ready for operation.

- The control housing with the CS 300 RM

control unit is installed.

Information:

For the installation of the gate/door, the MFZ

geared motor and the command and safety

devices, the relevant manufacturer’s instruc-

tions are to be adhered to.

5.2 Mains connection

Danger!

To ensure that the control unit functions pro-

perly, the following conditions must apply:

- The supply voltage must correspond to the

voltage shown on the type plate.

- The supply voltage must correspond to the

voltage of the door operator.

- If a permanent connection is to be made, an

all-pole mains switch must be installed.

Warning!

Before switching on the control unit for the

rst time, check to ensure that the cabling

works are complete and that all the motor

connections are secure at both the motor and

the control unit. All control voltage inputs are

separated galvanically from the mains power

supply.

6 – CS 300 RM Gate Controls / Rev. B 1.0

5. Initial operation

5.3 Assignment of connections for the motor

and the power supply

(terminal X1)

Terminal block X1

L1 N PE PE PE N U1 U2 S1 S2 S3 S4

230V / 1PH

S1-S4

Connection of mains switch (optional)

Connection:

Connect the control unit to the mains.

Connect the control unit to the motor.

Cable groups must be secured in place with a cable tie close

to their terminals.

Information:

Technical data, see page 24.

5.4 Assignment of connections for command

and safety devices

Command and safety devices can be connected to terminals

X3, X4 and X5.

Terminal block X3

- CLOSE button

- impulse button 1

- OPEN button

- STOP button

- Emergency off, slack rope switch,

wicket door contact, draw-in

protection

Terminal block X4

(for optoelectronic safety edge protection)

Part OPEN2

- safety edge protection

OPTO

- drive-through light

barrier3

- 24 V DC / 250 mA4

1 sequence control

2 button or selector switch

3 effective in down direction

for external switching devices (connection to terminals 1

and 2)

wt: white

gr: green

br: brown

CS 300 RM Gate Controls / Rev. B 1.0 – 7

Terminal block X4

(for 8.2 kOhm safety edge protection)

- safety edge protec-

tion

- drive-through light

barrier -3

- 24 V DC / 250 mA4

Klemmleiste X4

(mit Vorendschalter für Reversierabschaltung)

- before-end switch

Terminal block X4

(for 3-wire light barrier)

- 3-wire light barrier

Terminal block X5

(potential-free switch contacts)

- relay 1

- relay 2

- relay 3

- relay 4

8k2

24V

GND

8 – CS 300 RM Gate Controls / Rev. B 1.0

5. Initial operation

Key switch OPEN / CLOSE

- CLOSE

- OPEN

Impulse button

(sequence control)

- impulse button

Connection:

Connect any installed command and safety devices to the

control unit.

5.5 Connection examples for command and

safety devices (terminal X3)

OPEN / STOP / CLOSE buttons

(6-lead solution)

- CLOSE button

- OPEN button

- STOP button

OPEN / STOP / CLOSE buttons

(4-lead solution)

- CLOSE button

- OPEN button

- STOP button

CS 300 RM Gate Controls / Rev. B 1.0 – 9

10 – CS 300 RM Gate Controls / Rev. B 1.0

6.1 Overview of the LED module

Key:

LED off

LED illuminated

LED ashing

6. Programming with the LED module

6.2 Operating modes of the LED module

With the LED module, the control unit has two modes of operation:

1. AUTOMATIC

2. ADJUSTMENT

Information:

The current mode of operation of the control unit is shown via the LEDs.

- In AUTOMATIC mode, no LEDs ash. The (+) and (-) buttons have no function.

- In the ADJUSTMENT mode, at least one LED ashes. The external buttons have no function.

Pressing the (P) button toggles between the modes of operation.

Operating mode 1: AUTOMATIC

In the AUTOMATIC operating mode the door system is operated automatically.

LED displays:

H1 H2 Status

The door is open. The OPEN limit switch has been reached.

The door is closed. The CLOSED limit switch has been reached.

The door is between end positions. No limit switch has been reached.

The OPEN and CLOSE limit switches have been interrupted

(illogical state = TERM SWITCH FAIL).

Indice

Altri manuali MFZ Ovitor Apricancello

MFZ Ovitor

MFZ Ovitor AS 210 B Manuale utente

MFZ Ovitor

MFZ Ovitor E6L Manuale utente

MFZ Ovitor

MFZ Ovitor CS 300 Manuale utente

MFZ Ovitor

MFZ Ovitor MDF Series Manuale utente

Manuali Apricancello popolari di altre marche

Elite

Elite CSW200UL Manuale utente

CAME

CAME FROG-PM4 Manuale utente

SOMFY

SOMFY FX230 Manuale utente

Aprimatic

Aprimatic ONDA 500 Manuale utente

Turnstiles

Turnstiles FSW 900 Manuale utente

Erreka

Erreka BUL BL33 Istruzioni operative

Erreka

Erreka VULCAN S Manuale utente

Beninca

Beninca R1-2 WBV Manuale utente

Erreka

Erreka VULCAN D Manuale utente

Motorline professional

Motorline professional FORT Manuale di istruzioni

Beninca

Beninca BOB5024 Manuale utente

AGA

AGA GATEMASTER 900 HD Manuale utente

Chamberlain

Chamberlain MotorLift HC280ML Manuale utente

SOMFY

SOMFY Dexxo RTS Pro Manuale utente

Cardin

Cardin BL Series Manuale utente

Westfalia

Westfalia 85 27 06 Manuale utente

CAME

CAME F500 Manuale utente

Extel

Extel VERA Manuale utente