Miboxer TRI-C1 Manuale utente
Subordinate New Brand
AC Triac RF+Push Dimmer
Model No.: TRI-C1
1. Feature
No need to change orignal electric circuit
and install signal cable , low cost price,
convenient to construct. Dim light through
remote and Link code / Unlink code
simply. Small and exquisite apperance
which is easy to insert into EU and USA
standard wire box. It's convenient to wire
and install. It has wide application for
single color Triac dimmable led light,
traditional filament lamp and halogen
lamp.
● Support 2.4RF remote dimmable, control
distance is 30m
● Support Push dimmable
● Trailing edge(ELV) phase-cut
● 0~100% stepless dimming technology
● Set up min brightness via remote quickly
● Overheat/overloading protection
● Support auto transmitting and
synchronization, it has unlimited control
distance
● Output and input with screw connection,
install simply
● PC shell is fire-resistance
2. Parameters
Model No.: TRI-C1
Input Voltage: AC100~240V 50/60Hz
Output Voltage: AC100~240V
Output Current: Max 1.36A
Output Power: 150W @110V；300W @220V
Dim Method: RF wireless dimming,
Push dimming
Control Distance: 30m
Working Temperature: -10~40℃
25mm 49mm
49mm
3. Connection Diagram
N
L
Push switch
Input: AC100~240V
Triac dimming LED light
Traditional filament lamp
Halogen lamp
Please ensure all cable connected with
right way before turn on power supply,
otherwise it will damage the dimmer.
Warning
NC N LL1
N L
INPUT
OUTPUT
4. Installation Diagram
5. Push Dimming
Support following standard bottom case
Push switch
Botton case depth is
over 50mm
Short press push switch:
turn on or turn off light.
Long press push switch:
stepless dimming brightness.
Long press / release and long press
again to increase or decrease brightness.
If many triac dimmer connected with
same auto reset switch, please long press
20 seconds to sync all light with 100%
brightness. We suggest the quantity of
dimmer to connect with auto reset switch
less than 25pcs and the length of auto
reset switch cable is less than 20m.
2. Press" link/unlink" on
remote (like" " or " ")
3 times within 3 seconds.
Link code is done if the
light is flashing 3 times
slowly.
2. Press "SET" button on
remote 3 times within 3
seconds, matching is
done once the light is
flashing 3 times slowly.
6. Link code
1. Enter into learning code mode.
K1 remote Link code
Link code with other remote
Solution1: short press
"SET" button 1 time, the
indicator is flashing
explosively.
Solution2: turn off the
dimmer 10 seconds
and turn on again.
Solution3: short press
push switch to lighting
up mode.
1. Enter into learning code mode.
SET
indicator light
SET
Link / Unlink button
7. Unlink code
Unlink code with other remote
Solution1:
Long press "SET" button on dimmer 3
seconds untill the indicator is flashing
quickly, Unlink code is done.
Solution2:
K1 remote Unlink code
1. Enter into learning code
mode.
2. Press "SET" button on
remote 5 times with 3
seconds, the light is
flashing 10 times quickly,
Unlink code is done.
SET
2. Press" link/unlink" on
remote (like" " or " ")
5 times within 3 seconds,
the light is flashing 10
times quickly,Unlink code
is done.
1. Enter into learning code mode.
Link / Unlink button
9. Set up min brightness
8. Compatible remote
( buy separately)
This item should be paired with remote
firstly before setting.
Set up min brightness with K1
1. Long press "SET" button on remote 3 seconds
untill the light is flashing one time and
indicator of dimmer is going to flashing
status.
2. Short press "SET" button on remote to set up
10 different brightness figure :
3%,5%,7%,9%,12%,17%,22%,28%,34%,40%.
3. Short press rotating button on remote to
confirm setting up or waiting 10 seconds for
confirming automatically and log out set up.
The brightness of lamp will recover previous
brightness before setting up.
WL-Box1
K1
10. Auto Transmitting
8. Compatible remote
( buy separately)
Setting up min brightness with
other remote
1. Long press "SET" button on remote 3 seconds
untill the light is flashing one time and
indicator of dimmer is going to flashing
status.
2. Short press "SET" button on remote to set up
10 different brightness figure :
3%,5%,7%,9%,12%,17%,22%,28%,34%,40%.
3. Short press rotating button on remote to
confirm setting up or waiting 10 seconds for
confirming automatically and log out set up.
The brightness of lamp will recover previous
brightness before setting up.
1. Long press "off" button between remote
and dimmer ( like: " " or " "）untill the
light is flashing one time and indicator of
dimmer is going into flashing status.
Note： The master "OFF" button can set up
min brightness for all connected dimmers.
Dimmer can transmit signal to another one
within 30m, control distance is unlimited if
everything 30m install one dimmer.
Attention:
All dimmer should pair with one remote.
Triac
dimmer
Triac
dimmer
transmitting signal
distance 30m distance 30m
2. Short press " off " button between remote
and dimmer ( like: " " or " "）to set up
10 different brightness figure:
3%,5%,7%,9%,12%,17%,22%,28%,34%,
40%.
3. Short press any button on remote except "OFF"
to confirm setting up or waiting 10 seconds for
confirming automatically and log out set up.
The brightness of lamp will recover previous
brightness before setting up.
11. Attention
1. Please turn off power while install device.
2. Kindly check input voltage before
installation.
3. Don't disassemble device if you are not
professtional user, otherwise it will
damage device.
4. Don't use it near metal or magnetive
area, otherwise it will affect control.
1. Long press "off" button between remote
and dimmer ( like: " " or " "）untill the
light is flashing one time and indicator of
dimmer is going into flashing status.
Note： The master "OFF" button can set up
min brightness for all connected dimmers.
Made in China
Dimmer can not
use in humid area
Attention:
All dimmer should pair with one remote.
2. Short press " off " button between remote
and dimmer ( like: " " or " "）to set up
10 different brightness figure:
3%,5%,7%,9%,12%,17%,22%,28%,34%,
40%.
3. Short press any button on remote except "OFF"
to confirm setting up or waiting 10 seconds for
confirming automatically and log out set up.
The brightness of lamp will recover previous
brightness before setting up.
Indice
Altri manuali Miboxer Dimmer
