Microlink ML-891X Series Manuale utente

Infrared High Speed Dome Camera

（Fourth-generation / IV）

Operating manual

8891X series

Version: V2.0

ML-

Infrared Intelligent High Speed Dome Camera Operating Manual

This copyright belongs to our company. Without permission，any units or individuals shall not in any form or

any means to copy or plagiarize part or the whole of the book content.

Our company follows the strategy of sustainable development. Therefore, the company keeps the right to

modify and improve any products described in this specification under the condition of the no notice in advance .

Safety Caution

1. Before using the camera, please read the attached manual carefully to ensure the correct operation.

2. Wall installation power supply box is with dangerous high voltage，and there is no any replaceable parts，

Laypeople please don't open shielding cover. When wiring, must abide by the electrical safety standards,

please don't choose other power adapter to supply electricity to the camera.

3．The camera video signal cable and RS-485 wiring mouth of control line used ceramic gas discharge tube,

TVS tube instant discharge lightning technology, which can prevent the lightning under 500 W power, surge

and other kinds of pulse of high voltage to damage the interior of the camera.

4．In order to protect the camera not to be damaged by lightning stroke, please use marked the ground wire

ports of preventing lightning plate to access the earth. If no, lightning protection performance will be greatly

reduced.

5．The interior of the camera has high precision structural element, please transport properly.Please do not

leave the camera on the unstable desk or scaffolds to test, insure installation is firm before operation.

6. The camera video signal cable and RS485 control line must be far from high voltage lines as possible, to

avoid touch lines.

7. no matter not in use or be in use，prohibit putting the camera aiming at the sun or other high light objects.

If no, it will cause permanent damage of the CCD in camera interior.

8．When the camera malfunction，with reference to the manual to find fault, if can not find out the fault cause ,

contact professional maintenance persons to maintain. About relevant maintenance work, that must be

maintained by maintenance persons who authorized by our company.

Infrared Intelligent High Speed Dome Camera Operating Manual

Contents

1．Installation and debugging of infrared high speed dome camera

1 .1．Infrared high-speed component name

1.2．Istalling hole dimension figure

1. 3．Installation and debugging method

2．Infrared high-speed dome camera setting and operation

2.1．Technology parameter table

2.2．Common functions glossary

2.3．Address, protocol, baud rate setting

2.4．Address dip table

2.5. Control equipment

2.6. Boot initialization

2.7. Basic operation

3．AUTOMATIC OPERATION SETTING > menu operation <

3.1．< PRESET POINT >setting

3.2．< LEFT-RIGHT SCAN > setting

3.3．< CRUISE SCAN> setting

3.4．< PATTERN SCAN> setting

3.5．< TIME ACTION > setting

3.6．< WAIT ACTION > setting

3.7．< PANTILT SETTING > setting

4. <CAMERA SETTING>menu operation

4.1．< LENS PARAMETERS > setting

4.2．< EXPOSUREMODE > setting

4.3．< WHITE BALANCE > setting

4.4．< BACKLIGHT MODE > setting

4.5．< PRIVACY MASK > setting

5. <DISPLAY SETTING>menu

6. <SYSTEM SETTING>menu

7.<ALARM SETTING> menu operating

8. <IR LED SETTING> menu operation

9. Simple troubleshooting table

Infrared Intelligent High Speed Dome Camera Operating Manual

1．Installation and debugging of Infrared High Speed Dome Camera

1.1．Infrared high-speed component name

1.2．Installing hole size figure

Whole set size (mm) Installing hole size (mm)

Infrared Intelligent High Speed Dome Camera Operating Manual

1.3． Installation and debugging

1.3.1、Take out the main dome, wall bracket, wall boxing and other components.

1.3.2、Paste the wall boxing to the wall, according to the wall boxing size to drill corresponding hole, then install

the expansion bolts.

1.3.34、Hang the wall bracket on the rotation door.

1.3.4、Plug the cable row into the socket signed "TO DOME" on the right of prevent lighting plate.

1.3.5、penetrate the video cable and 485 controls thread from waterproof screw, and contact to the corresponding

outlet signed "OUTPUT LINE" on the left of prevent lighting plate.

1.3.6、If the distance between dome and the control equipment more than 500M, Push the eight Matching

resistance to “ON” on the DIP switch board SW1 .

1.3.8、Finally, tighten the two mounting screws. Access to 220V AC power supply must pay attention to color

-coded. (Blue and brown zero line and FireWire, yellow is earth wire)

Lighting protection board lines connection

program input

Infrared Intelligent High Speed Dome Camera Operating Manual

2、infrared high-speed dome camera setting and operation

2.1．technology parameter table

2.2．Common Functions Glossary

Preset setup：Save some locations that need to be usually monitored,so that can find these locations easily.

Call preset：To run the machine quickly and accurately to a pre-stored location, or execute a specify function.

Left-right scan setup：Set the machine scan back and forth between two points in a certain area. Also

known as A-B Scan.

Cruise setup：Set the machine scan between some preset points, and each preset dwell time between the

points can be set freely.

Pattern Setup：record the scanned line and store it into the machine, easy to play back or run the line at

any time.

Time action：Set the machine to run a certain function at a specific time.

Wait action：After a period of time without any operation, the ball automatically run to the specified preset

point guard, or run a preset function.

Alarm Linkage：When an alarm signal is input, the machine immediately execute pre-configured functions,

and can be linked to other output devices.

Power Supply

Video Output

Communication

Dome Address

Communication Protocol

Baud Rate

Horizontal Rotation Speed

Horizontal Rotation Range

Vertical Rotation Speed

Vertical Rotation Range

Manual Control Speed

One Machine Set

Infrared light(Spec x pcs)

IR Distance

Preset Points

A-B Scan Speed

Cruise scanning

Pattern scanning

Idle Running

Timing of operation

Privacy protection

Password protection

Information Display

Alarm Linkage

Working Temperature/ Humidity

Automatic thermostat indicator

Waterproof

Dimension

Net Weight

AC220V/50Hz or AC110V/60Hz

1.0V p-p 75Ω

RS485

1-255(Support software rewriting address)

Pelco-D/Pelco-P / SANTACHI 650 / FACTORY

2400/4800/9600/19200 bps

220º/s (1-64级变)

360º unlimited

90º/s

0-90º

200º/S

Compatible with SONY,HITACHI,SAMSUNG,LG,SANYO.CNB etc

Φ5 IR LEDs 108pcs / Array LEDs 10pcs

100-120m

220 points

4 groups(1-64 grade speed available)

4 groups(at most 32 preset points each group)

4 groups(at most 100 continuous action each group)

After setting idle 5-255S,it scans automatically

4 groups(can operate at any setted time the whole day)

Can be set to 8 protected areas

Can be set to 6 numbers password

Date,time positon,temperature,etc

Support 4ways output,2ways input, colse/open optional

-40℃—+60℃, ≤95% (no condensation)

<-5℃ Heating， >48 Cooling℃

IP65

360（L）×318（W）×180（H）mm

5.1kg

Infrared Intelligent High Speed Dome Camera Operating Manual

Power-off memory：When the machine restart after power failure, it will automatically revert to the last

stop position or the last working state.

High zoom low speed： with manual zoom lens value increases，the manual control speed in proportion

to slow down.

Far and Near conversion：In night mode, far/near-infrared light automatically converted according to

the lens multiplier. When the lens multiplier nearly 13 times, the near lights

on. When above 13 times, the far light on.

Day/Night conversion：the machine identify the current ambient light through photosensitive Resistance,

turn on the infrared lights, and convert black and white images automatically.

Automatic Focus：If the product is set to auto-focus mode, When the user control PTZ, the camera always

follow the auto-focus.

2.3．Address, protocol, baud rate setting

After machine installed, be sure the ball machine set DIP switch address code, protocol, baud rate is fully

consistent with the control equipment. Our High speed Demo camera default address is 1, communication

Protocol Pelco-D, Baud Rate 2400bps. Corresponding DIP switch status is as follows：

If you need to change the protocol setting, please refer to the following diagram to set the DIP：

If you need to change the baud rate setting, please refer to the following diagram to set the DIP：

Camera Address Setup

Empty

Baud Rate setup

Communication Protocol Setup

Infrared Intelligent High Speed Dome Camera Operating Manual

2.4．Address DIP table（1 means ON，0 means OFF）

Binary code Address Binary code Binary code Address Binary code Binary code Address

Infrared Intelligent High Speed Dome Camera Operating Manual

2.5 Control equipment

According to users’ need, below are the equipments normally used：

Control borad PC（Video capture card）

DVR tester（specially for project）

Binary code Address Binary code Address Binary code Address Binary code Address

Operation instructions: As the specific operation ways are different for Variety of controlling

equipments, please refer to the referring manual. IR high speed dome camera advise all users collocate

special controlling board, more using convenient. All the operation ways of this manual are taking

controlling board operating as example.

1（Software

modify）

Infrared Intelligent High Speed Dome Camera Operating Manual

2.6．Boot initialization

Connect the video line and 485 controlling line to the monitor or DVR, ensuring that the connection is right then

catch 220V power to the power case of camera.

The ir high speed dome camera outpour signal to the screen and start searching varity of collocating information,

about after 10 seconds, the screen will show the list of the camera’s initialization, as picture 1.

At the mean while, the PTZ starts check up, down, left and right, after checking will show” system initialization

success”. Then it will standby（picture 2） or get back to the status as the last time off power.

When at standby status, it will show varieties of operating stuffs’ name on the left-up the screen, such as:

camera name, preset name, A to B scanning name, cruise scanning name and pattern scanning name.Current

date,time,surveillance direction,ptz location,lens multiple,temperature and so on. If no need to show,p.l.s

enter the menu<showing information setting> and set:close.

2.7． Basic operation

Frame: select surveillance area.user can operate the rocker up,down,left,right to move the holder to find the

surveillance direction. By operating the keyboard ”zoom+” or “zoom-“,zoom the image. Press”focus+” or

“focus-“,to adjust lens focus manually.

Set presets:We can set the often monitored location as presets and save in the camera,use number for

saving,the camera’s maximum quantity of preset is 220. When it shows preset setting successfully,the screen

will point out “preset saved”. Showed by picture 3:

Picture1 checking

information when start up:

Picture 2 standby status:

Indice

Altri manuali Microlink Telecamera di sicurezza

Microlink

Microlink 8890X Series Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente