MicroNet Mn100 Manuale utente

mn100

Dual Digital Display

uu037 rev. 8

mn100 Dual Digital Display

EMC Conformance

All Tacktick equipment is designed to the best industry standards for

use in the recreational marine environment. The design and

manufacture of Tacktick equipment conforms to the appropriate

Electromagnetic Compatibility (EMC) standards. Correct installation is

required to ensure that performance is not compromised.

Important

Due to the wireless communication systems used in Micronet

instruments they are only recommended for use on boats up to 14

meters (45 ft.) which are of glass, carbon, or wooden construction.

Like any other Electronic instruments your Micronet system is

designed to serve only as an aid to navigation and it remains the

skippers responsibility to maintain a permanent watch and be aware

of developing situations.

mn100 Dual Digital Display

6.2.10 No NMEA data showing on external instruments.

From any Digital instrument enter Setup and Calibration Mode (page

18) and scroll through to the Health Chapter. Check the signal level

and battery status of the NMEA Interface. If the signal level shows a

value of greater than 3 then check the data connections and the

settings of the NMEA source equipment to ensure that NMEA 0183 is

being transmitted correctly.

* The “Master Instrument” is the instrument which was used to power up

the entire system. This instrument may be different each time the

system is used. If you are fault finding and are uncertain which

instrument is the master the switch off the system and switch on again.

The instrument which you switched on is now the master

Warranty Information

Tacktick Limited or its authorized Distributors will repair or replace a

Tacktick product free of charge where a manufacturing fault becomes

apparent within two years of the purchase date provided:

1. No unauthorized attempt has been made to repair the

product.

2. The product has not been misused, operated outside of its

intended environment or operated in a manner which is

incompatible with the written instructions supplied on

purchase.

Proof of purchase date is required for the warranty period to

be valid.

Due to the removable nature of the Tacktick product, on board service

will only be available with prior consent from Tacktick or its authorized

Distributors.

Failure within the warranty period:

Simply return the product to your nearest authorized Tacktick

Distributor, together with proof of purchase date.

Failure outside the warranty period:

Simply return your product to the nearest authorized Tacktick

Distributor and an estimation for repair will be provided.

Authorized Tacktick Distributor details can be found at

www.tacktick.com, or on the back of Tacktick sales brochures.

Introduction

1 Information

1.1 Introduction - 2

1.2 Specifications - 2

1.3 Power Management and Battery Life - 2

1.5 Safety and Disposal - 5

2 Operation

2.1 Instrument Display Information - 5

2.2 Switching the System On and Off - 6

2.3 Backlighting - 6

2.4 Audible Signals and Alarms - 7

2.5 Chapter and Page Operation - 8

2.6 Chapter and Page Description - 10

3 Setup and Calibration

3.1 Entering Setup and Calibration Mode - 18

3.2 Chapter and Page Setup and Calibration - 18

3.3 Editing Values - 19

3.4 Setup Page Description - 20

3.5 Calibration Page Description - 22

4 Seatrial and Calibration

4.1 Depth Offset - 26

4.2 Speed Calibration - 27

4.3 Wind Calibration - 28

4.4 Compass Calibration - 29

5 Installation

5.1 Tools List & Parts - 30

5.2 Precautions and Positioning Advise - 30

5.3 Bracket Mounting - 31

5.4 Surface Mounting - 33

5.5 External Power Connections - 33

6 Maintenance and Fault Finding

6.1 Care and Maintenance - 34

6.2 Fault Finding and Technical Support - 34

6.3 Warranty Information - 37

mn100 Dual Digital Display

1 - Information

1.1 Introduction

Your Micronet instrument is powered for life by the environment.

Although feature packed and highly visible in all conditions, current

demand is so low, and the supply so efficient, that the solar-powered

display is self sufficient. Combined with other instruments in the

Micronet range this display becomes part of a complete navigational

system.

1.2 Specifications

Height of digits: 20mm (0.8”)

Backlighting: 3 levels with daylight shutoff

System-wide or local control

Power: Solar Powered

300 hrs autonomy by day, 7 nights at brightest

backlighting, 20 nights at economy backlighting

without charge

Units of display: Boat Speed

(knots,kilometers per hour,statute miles per hour)

Distance

(nautical miles, statute miles, kilometers)

Depth

(meters, feet, fathoms)

Wind Speed

(knots, meters per second, Beaufort)

Alarm: Audible Alarm for Depth, Wind and MOB

Weight: 285g (0.63lbs)

Operating Temp.: -100 to +600C (140 to 1400F)

Frequency: 868 MHz or 905 MHz

1.3 Power Management and Battery Life

What makes your mn100 instrument possible is Tacktick’s

revolutionary approach to power management. By reducing the

amount of power being used by the electronics and maximizing the

potential of the sun to provide power, a mn100 instrument becomes a

virtually perpetual device.

Power status is indicated by two icons on the instrument display:

Battery Level and Charge Rate

Used together these icons will show the condition of your instrument’s

power supply.

Maintenance and Fault Finding

6.2.4 Low Battery Alarm sounds.

The power level is low in the Hull Transmitter, NMEA Interface or Wind

Transmitter. On any Digital Instrument enter Setup and Calibration

mode (Page 18) and scroll through to the Health Chapter. Check the

signal levels of the Transmitters and Interface Box. The signal level

should show a value of greater than 3 to ensure correct operation.

Connect the Hull Transmitter or NMEA Interface to a 9 to 24V power

source for 12 hours minimum to recharge the internal battery. Leave

the Wind Transmitter in bright sunlight for 12 hours minimum to

recharge its internal battery.

6.2.5 Data is shown as dashes.

The information is not been transmitted to the instrument Displays.

There may be lost communication between the Wind Transmitter or

Hull Transmitter and the instrument Displays. On any Digital

instrument enter Setup and Calibration mode (page 18) and scroll

through to the Health Chapter. Check the signal levels of the Hull and

Wind Transmitters. The signal level should show a value of greater than

3 to ensure correct operation.

6.2.6 Compass Transducer rattles and/or splashes.

Good! The fluxgate compass is gimballed in a fluid filled container to

ensure it is not affected by the boats movement in the water.

6.2.7 Compass information displayed on the instrument system does

not agree with the main steering compass.

Ensure that the main steering compass has been swung correctly and is

showing correct information. Ensure that the instrument system has

completed correctly the “Swing” procedure described on page 29. If

there are still differences, look for magnetic objects (loud speakers,

pumps and motors, etc.) close to the Transducer and try mounting the

compass transducer in an alternative location. After changing position

of nearby equipment or the Compass Transducer it will be necessary to

re-swing the compass following the procedure on page 29.

6.2.8 Boat Speed reads 0.

Information being transmitted from the Hull Transmitter is being

received with a Zero value. Check the paddle wheel for fouling, clean it

and make sure it turns easily.

6.2.9 Wind Speed reads 0.

Information being transmitted from the Wind Transmitter is being

received with a Zero value. If the anemometer cups at the top of the

mast are turning and the Wind Speed reads 0 then there is a problem

with your Wind Transmitter.

6.2.11 The Depth Alarm does not sound.

If the actual water depth is shallow and the alarm has not sounded it is

most likely that the alarm is switched off. From any Digital instrument

enter Setup and Calibration mode (page 18) and scroll through to the

Depth Chapter. Ensure the Depth Alarm settings are correct.

mn100 Dual Digital Display

5.4 Surface Mounting

5.4.1 Where there is no access to the rear of the

mounting surface

Easy installation but will allow removal without gaining access to the

boat. Position the supplied Template carefully before starting.

1. Drill three 2mm holes marked “SURFACE” on the Template

2. Carefully snap the facia of the instrument off the main body

taking care not to drop the button pads. .

HINT – It may be useful to place a piece of sticky tape

across the front of the buttons before removing the facia to

prevent them from falling out during the installation.

3. Remove the three captive M4 nuts from the plastic moulding

and attach the instrument to the mounting surface using the

three self tapping screws provided. Take care not to over

tighten the screws as this may cause the moulding to crack.

4. Check the instrument is perfectly level, carefully position the

button inserts into the correct slots and snap the facia back

into position.

5.4.2 Temporary Mounting

1. Use the double sided tape provided to secure the instrument

to a suitable mounting surface. Press the instrument firmly

against the surface until secure.

Note: This method is recommended for temporary use only.

Operation

2 – Operation

Important:

Ensure that the “Auto Network” procedure described on the yellow

instruction sheet and full Setup and Calibration has been performed

correctly before attempting to use your Micronet instruments for

navigation purposes.

2.1 Instrument Display Information

mn100 Dual Digital Display

If there is no boat speed or change in heading registered on the

system for a period of 12 hours your Micronet instrument will switch

off to conserve power. A “POWER SAVE” alarm will sound before the

instrument system is switched off. Pressing any button within 10

seconds of the alarm sounding will allow the system to remain

switched on.

Backlighting will automatically shut down/off when operated in

daylight.

Artificial light WILL NOT recharge the battery. Placing

your Micronet instrument close to an artificial light will

seriously damage the instrument. Only recharge in natural

daylight.

Applying External Power

In cases where instruments are mounted permanently below decks it

will be necessary to apply an external power source to prevent

complete discharge of the built in battery.

Connections on the rear of the instrument allow a 9V to 24V DC power

source to be connected. Connections can be made to the vessels DC

system or a 9V battery pack may be connected. It is recommended

that permanent connection is only made when the instruments are

permanently fixed to the vessel and not when the clip brackets are

used.

Connection to a 9V (PP3) battery will fully recharge the internal

battery over a period of 24 hours.

1.4 Safety and Disposal

Your Micronet instrument contains Manganese Lithium Dioxide

batteries which should be disposed of correctly. Do not dispose of any

instrument in domestic waste. Refer to regulations in force in your

country.

If in doubt return the instrument to Tacktick Ltd. for correct disposal.

Installation

5.4.3 Where access is available to the rear of the

mounting surface

This method allows for maximum security of a permanently mounted

instrument. Position the supplied Template carefully before starting.

1. Drill three 5mm holes marked “B” on the Template.

2 Stick the 3 supplied gaskets on the back of the instrument.

3. Screw the four M4 brass studs into the rear of the

instrument.

4. Place the instrument in position pushing the three studs

through the newly drilled holes.

5. Using the three supplied thumb nuts, secure the instrument

to the surface making sure the instrument is level before

final tightening.

5.5 External Power Connections

To connect an external 9 to 24 volt power supply to the instrument

head from either a portable battery or the vessel’s existing power

system.

1. Drill two 7mm holes marked “P” on the Mounting Template

and smooth them together with a sharp knife or small file.

2. Pass the supply cable through the new hole and attach the

supplied crimp spade receptacles.

3. Remove the blanking plug from the rear of the instrument to

expose the terminals.

4 Stick the supplied gasket on the back of the instrument.

5. Taking care to connect the correct polarity push the

receptacles firmly onto the spades on the rear of the case.

6. Mount the instrument head securely in position following the

steps shown above.

7. Clamp the cable securely close to the instrument.

mn100 Dual Digital Display

6 Maintenance and Fault Finding

6.1 Care and Maintenance

All Micronet products are totally sealed against water and are not

serviceable. Any attempt to take a Micronet product apart will

invalidate the warranty.

To clean, use only a damp, soft cloth. No detergents, solvents or

abrasives should be used. To avoid damaging a Micronet display unit

we recommend storing in the supplied soft pack when not in use.

If the instruments are to be stored for a long period of time before

next use (Over Winter) ensure that the batteries are fully charged

before storage. If necessary connect to a 9 to 24v power supply for

24 hrs prior to storage.

6.2 Fault Finding and Technical Support

6.2.1 Power Save Alarm sounds.

There has been no significant data activity on the network. The alarm

sounds to indicate that the instrument system will turn itself off. To

continue using the system press any button to cancel the alarm.

6.2.2 Lost Network Alarm sounds.

On a single instrument this indicates that the particular instrument has

lost communication with the Master*. Either there is a problem with the

Master* instrument or the instrument in question has been moved out

of effective range.

On several instruments this indicates that these instruments have lost

communication with the Master*. Either there is a problem with the

master or the Master* has been moved out of effective range. The

instruments will power down shortly after sounding the alarm to save

power.

6.2.3 A single instrument flashes the battery symbol and then

switches off.

The battery level is low on the particular instrument affected. Connect

to a 9 to 24V power source or leave in bright sunlight for 12 hours

minimum to recharge the instrument’s internal battery. If the particular

instrument is the system Master* then the other instruments will sound

the Lost Network Alarm. To continue using the rest of the system

power down and restart the system from another instrument.

Introduction

and Battery is charged and being

topped up by the sun. *

Bright Sunny

Day

and Battery is low and being charged

by the sun.

and Battery is charged and requires no

further charging.

Overcast Day

and Battery is low but maintaining it’s

level.

and Battery is charged but is not

charging.

Night

and Battery is low with no charging.

LOW Power and

Flashing

It is recommended that the

instrument be left in daylight for

some time for the battery to

recover, or charge from an

external 9 - 24V power source. A

fully discharged battery will re-

charge in approximately 12 hours

of direct bright sunlight.

If using the instruments at night power usage can be reduced

dramatically by switching the Backlighting to level 1 or Off. If

Backlighting is not required on instruments located below decks it is

best to set them to “Local” Backlighting control (see page 26 -s31) so

that power is not being wasted in instruments which may not be

visible from the one being viewed.

* If the internal battery is fully charged then it does not matter

how much the instrument is subjected to bright sunlight no further

charging is required and the Charge Rate Indicator will remain low.

If the instruments are to be stored for a long period of time before

next use (Over Winter) ensure that the batteries are fully charged

before storage. If necessary connect to a 9 to 24v power supply for

24 hrs prior to storage.

mn100 Dual Digital Display

2.2 Switching the System On and Off

To switch on your Micronet

system select any instrument

and press the button for 2

seconds.

To switch off your Micronet

system select any instrument

and press and hold the

button for 2 seconds.

2.3 Backlighting

At any stage of the instrument’s

operation press and hold for 2

seconds the button to

access the lighting control.

Pressing the and

buttons will scroll through

setting OFF, 1, 2 and 3 whilst

changing the Backlighting.

Depending on the instrument

setup (see page 20 -s5),

Backlighting on the whole

system or just the single

instrument will be altered.

Backlighting is automatically switched off in daylight as part of

the instrument’s power saving feature and will not operate in daylight.

Installation

5.3 Bracket Mounting (Preferred Method)

This method allows for the easy removal of an instrument as and

when required, for either security reasons or to prevent damage or

discomfort whilst not in use.

1. Using the three supplied M4 bolts attach the back plate to

the rear of the instrument (Fig.1).

2. Drill three 2mm holes marked “BRACKET” on the Template

and using the supplied self tapping screws attach the clip

bracket to the mounting surface (Fig.2).

3. Place the instrument flat against the bracket slightly higher

than the final position and slide gently down into position.

There will be a small click as the bracket secures the

instrument into position (Fig.3).

4. To release the instrument press lightly on the bracket tab

and slide the instrument upwards (Fig.4).

mn100 Dual Digital Display

5 Installation

5.1 Tools Required and Parts List

1. 2mm or 5mm Drill Bit (7mm

if power connection required)

2. Power Drill

3. Cross Head Screwdriver

1. Mounting Template

2. Display Bracket

3. Mounting Screws (3)

4. Mounting Bolts (3)

5. M4 Studs & Thumbnuts (3)

6. Sealing Gaskets (4)

7. Double Sided Tape

5.2 Precautions and Positioning Advice

Ensure mounting surface is flat.

Leave space between instruments for sun covers.

Leave space to remove instrument from bracket (if used).

Avoid areas where damage may occur (winch handles ,feet, warps

etc.)

Select a flat, smooth, surface for mounting and use the Template

provided to select a suitable position for mounting your Micronet

instrument.

Check for clarity of vision and ease of access to the control buttons, it

is recommended that instruments are positioned such that your arm

does NOT pass through the spokes of the steering wheel when

operating the buttons.

Contrast is limited at night when an instrument is

viewed from beneath. Avoid mounting instruments in a

position where you will look upwards to view them.

Operation

2.4 Audible Signals and Alarms

At stages during its operation your Micronet instrument will beep to

indicate alarms or moments of importance.

Power-up Once operating as part of a network the instrument

will issue a single beep as it is switched on by

pressing the button for 2 second.

Button Press A single beep is issued each time a button is pressed

A second beep is issued after a 2 seconds hold down

of the button.

Alarm Continuous bursts of three beeps will indicate an

alarm. The alarm activated will be indicated on the

digital display, accompanied by the flashing

symbol. Pressing any button will silence the alarm.

Timer A single beep will be issued at each minute of the

countdown. With 1 minute left to go a beep will sound

every 10 seconds. With 10 seconds to go a beep will

sound every second.

Countdown complete will be indicated by a single

burst of three beeps.

mn100 Dual Digital Display

2.5 Chapter and Page Operation

Instrument information is displayed in a “Chapter and Page” format

using the (Chapter) button to scroll through the Chapters which

are displayed in the upper part of the window and the and

(Page) buttons to move between Pages within a Chapter which are

displayed in the lower part of the window.

Chapter Sequence Shown in Upper Window

(for a full description of each Chapter see page 10 - c1 to c8)

Setup and Calibration

4.4 Compass Calibration

To ensure that inaccuracies caused by metallic and magnetic objects

on the boat are kept to a minimum is necessary to calibrate the

compass. A deviation caused by surrounding objects will be

compensated for and the compass reading may be set to the correct

heading.

Press and hold the button for 2 seconds to enter Setup

Press the button repeatedly to scroll to the “SETUP/COMPASS”

Chapter

To Complete a deviation correction turn:

Press the button to advance to “DEV0” Page

Press the button to enter Compass Calibration Mode

Turn the vessel slowly keeping the speed below 4 knots and taking

approximately 2 minutes to complete 3600. Keep turning the vessel

until the display changes to display a value (usually about 1.25 turns)

Note: If the rate of turn of the vessel is too fast the instrument will

display “TURN HIGH”. It is not necessary to abandon the

turn at this stage but do lessen the rate of turn by reducing

speed or widening the turning circle.

Continue to align the heading

Steer the vessel on a known heading.

Note: only use the main steering compass as a known heading if

you are certain it has been checked and compensated.

Press the button twice to display HDG / +000

Press the button to enter Edit Mode

Press the and buttons to change to the known value. The

lower digits will display the offset entered.

Press the button to exit Edit Mode

Press and hold the button to exit Setup and return to normal

operation.

Indice

Altri manuali MicroNet Monitor

MicroNet

MicroNet Dual Maxi Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione

MicroNet mn100 Manuale utente

Manuali Monitor popolari di altre marche