Microsonic Mic+ Manuale utente









T1 + T2

Set detect distance in

mm or cm

For single detect

point press T2

until »- - -« is

displayed

Choose » « for NCC or

» « for NOC

T2



For window mode

operation set far

detect point in

mm or cm

T1 + T2



Press T1 and T2 simultaneously for about

3 s until welcome message has passed

T1 + T2







T1 + T2



T1 + T2



T1 + T2



T1

Set switched output

Ready

Start here

Set sensor parameters alternatively numerically using LED-display...

Product description

The mic+sensor with one switched output

measures the distance to an object within

the detection zone contactless. Depen-

ding on the adjusted detect distance the

switched output is set.

All settings are done with two push-but-

tons and a three-digit LED-display

(TouchControl).

Light emitting diodes (three-colour LEDs)

indicate the switching status.

The output functions are changeable

from NOC to NCC.

The sensors are adjustable manually using

the numerical LED-display or may be trai-

ned using Teach-in processes.

Useful additional functions are set in the

Add-on-menu.

Using the LinkControl adapter (optional

accessory) all TouchControl and additio-

nal sensor parameter settings may be

made by a Windows-Software.

Important instructions for assembly and

application

All employee and plant safety-relevant

measures must be taken prior to assembly,

start-up, or maintenance work (see operation

manual for the entire plant and the operator

instruction of the plant).

The sensors are not considered as safety

equipment and may not be used to ensure

human or machine safety!

The mic+ sensors indicate a blind zone, in

which the distance cannot be measured. The

operating range indicates the distance of the

sensor that can be applied with normal re-

flectors with sufficient function reserve.

When using good reflectors, such as a calm

water surface, the sensor can also be used up

to its maximum range. Objects that strongly

absorb (e.g. plastic foam) or diffusely reflect

sound (e.g. pebble stones) can also reduce

the defined operating range.

Synchronisation

If the assembly distances shown in Fig.1 for

two or more sensors are exceeded the inte-

grated synchronisation should be used. Con-

nect Sync/Com-channels (pin 5 at the units re-

ceptable) of all sensors (10 maximum).

Fig. 1: Assembly distances, indicating syn-

chronisation/multiplex

Multiplex mode

The Add-on-menu allows to assign an indivi-

dual address »01« to »10« to each sensor

connected via the Sync/Com-channel (Pin5).

The sensors perform the ultrasonic measure-

ment sequentially from low to high address.

Therefore any influence between the sensors

is rejected.

The address »00« is reserved to synchronisa-

tion mode and deactivates the multiplex

mode. (To use synchronised mode all sensors

must be set to address »00«.)

≥0.35 m

≥0.40 m

≥2.50 m

≥1.10 m

≥2.00 m

≥8.00 m

≥18.00 m

≥4.00 m

≥30.00 m

Assembly instructions

Assemble the sensor at the installation lo-

cation.

Plug in the connector cable to the M 12

connector.

Fig. 2: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

Start-up

mic+ sensors are delivered factory made with

the following settings:

Switched output on NOC

Detecting distance at operating range

and half operating range

Measurement range set to maximum ran-

colour

+UB

-UB

brown

blue

black

white

Sync/Com. grey

Set the parameters of the sensor manually or

use the Teach-in procedure to adjust the

detect points.

Fig. 3: TouchControl

Operation

mic+sensors work maintenance free. Small

amounts of dirt on the surface do not influ-

ence function. Thick layers of dirt and caked-

on dirt affect sensor function and therefore

must be removed.

Note

mic+sensors have internal temperature

compensation. Because the sensors heat

up on their own, the temperature com-

pensation reaches its optimum working

point after approx. 30 minutes of operati-

on.

During normal mode operation, a yellow

LED D2 signals that the switched output

has connected.

During normal mode operation, the mea-

sured distance value is displayed on the

LED-indicator in mm (up to 999 mm) or

cm (from 100 cm). Scale switches auto-

matically and is indicated by a point on

top of the digits.

During Teach-in mode, the hysteresis

loops are set back to factory settings.

If no objects are placed within the detec-

tion zone the LED-indicator shows »- - -«.

If no push-buttons are pressed for 20 se-

conds during parameter setting mode the

made changes are stored and the sensor

returns to normal mode operation.

You can lock the key pad to provide in-

puts, see »Key lock and factory setting«.

You can reset the factory settings at any

time, see »Key lock and factory setting«.

Show parameters

Tapping push-button T1 shortly during nor-

mal mode operation shows »PAr« on the

LED-display. Each time you tap push-button

T1 the actual settings of the switched output

are shown.

Operating manual

mic+ Ultrasonic Sensors with

one switched output

c m m

m %

T 1

1 D

2 T

measuring range

LED D1 and D2

3-digit

LED-display

Push-buttons T1 and T2

mic+25/D/TC mic+25/E/TC

mic+35/D/TC mic+35/E/TC

mic+130/D/TC mic+130/E/TC

mic+340/D/TC mic+340E/TC

mic+600/D/TC mic+600/E/TC

Enclosure Type 1

For use only in industrial

machinery NFPA 79 applications.

The proximity switches shall be used with a Lis-

ted (CYJV/7) cable/connector assembly rated mi-

nimum 32 Vdc, minimum 290 mA, in the final in-

stallation.

2014/30/EU

HM 1909

...or with the Teach-in procedure

Adjust detect point

Place object at position 

Press T2 until »d« is shown

Current measu-

ring value

Press T2 until »End« is

shown

Adjust window mode

Place object at position 

Press T2 until »d« is shown

Place object at position 

Current measu-

ring value

Press T2 until »End« is

shown

Current measu-

ring value

Adjust two-way reflectiv

barrier

Place reflector at position 

Set NOC/NCC

Press T2 until »d« is shown

Current measu-

ring value

Press T2 until countdown

passed from »- 8 -« to »- 0 -«

and NOC or NCC symbol is

displayed

Press T2 until countdown

passed from »- 8 -« to »- 0 -«

and »End« is displayed

To change output function

press T2

Press T1 and T2 simultane-

ously until »End« is dis

played

Symbol

NOC or NCC

Symbol

NOC or NCC

Normal mode operation

T1 + T2

T2



T1 + T2



Press T1 and T2 simultaneously for about 13 s

until »Add« is shown in the LED-display

T1 + T2

Start here







T1



T1 + T2



Ready



»C01«: Display

bright

»C02«: Display dim-

med

»C03«: Display off

To optimize multi-

plex speed the hig-

hest sensor address

may be set.

Setting range »01«

to »10«

»F00«: no filter

»F01«: standard fil-

ter

»F02«: averaging fil-

ter

»F03«: foreground

filter

»F04«: background

filter

Defines the strength

of the chosen filter.

»P00«: weak filter

up to

»P09«: strong filter

Affects the size of

the detection zone.

»E01«: high

»E02«: standard

»E03«: slight

Minimum value:

blind zone

Maximum value: ne-

arwindow limit - 1

Low power mode Measurement filter Filter strength Foreground

suppression

Multiplex mode

device addressing

Multiplex mode

highest address

»00«: synchronisati-

»01« to »10«: sensor

address for multi-

plex mode

»oFF«: synchronisati-

on deactivated

Minimum value: sen-

sor-distant window

margin

Maximum value: 999

mm for mic+

25/...,mic+35/...,

999 cm for mic+

130/...,mic+340/...,

mic+600/...

Measurement range Calibration

display

Detection zone

sensitivity

Put plane reflector

vertically disposed in

front of sensor: in

an exact distance of

250 mm for mic+

25... and mic+35...

and 900 mm for all

other typs.

Adjust display to

250 mm or 900 mm.

Confirm calibration

with T1 + T2.

T1 + T2

T1 T2

T1 + T2









T1 + T2

T1 T2

T1 + T2









T1 + T2

T1 T2

T1 + T2









T1 + T2

T1 T2

T1 + T2









T1 + T2

T1 T2

T1 + T2









T1 + T2

T1 T2

T1 + T2









T1 + T2

T1 T2

T1 + T2









T1 + T2

T1 T2

T1 + T2









Delay in seconds

between the detec-

tion of an object

and the output of

the measured dis-

tance in case of ob-

ject approach (beha-

ves as on-delay).

"00": 0 s (no delay)

up to

"20": 20 s response

time

Response time

T1 + T2

T1 T2

T1 + T2











Note

Changes in the Add-on

menu may impair the

sensor function.

A6, A7, A8 , A10 , A11,

A12 have influence on

the response time of

the sensor.

Hysteresis

switched output

Minimum value:

»001«

Maximum value: dif-

ference between

maximum range and

detect point - 1

During window

mode operation hys-

teresis influences

both detect points.

T1 + T2

T1 T2

T1 + T2









Usefull additional functions in Add-on menu (for experienced users only, settings not required for standard applications)

Teach-in swítched output

Key lock and factory setting

Activate/deactivate

TouchControl

Reset to factory set-

ting

Turn supply voltage

OFF

While pressing T1

turn supply voltage

ON until »on« or

»off« is displayed

Turn supply voltage

OFF

Turn supply voltage

ON while pressing T1

and keep it pressed

for ca. 13 s until

»rESEt« has passed

through the display

To activate or

deactivate press T1

»on« or

»off«

To activate or

deactivate press T1

»on« or

»off«

Normal mode operation

*5395*

MV-DO-041942-620674

Technical data

blind zone

operating range

maximum range

angle of beam spread

0 to 30 mm

250 mm

0 to 65 mm

350 mm

Please see detection zone

600 mm

Please see detection zone

0 to 200 mm

1.300 mm

0 to 350 mm

3.400 mm

2.000 mm

Please see detection zone

5.000 mm

Please see detection zone

0 to 600 mm

6.000 mm

8.000 mm

Please see detection zone

transducer frequency

resolution, sampling rate

reproducibility

accuracy

320 kHz

0,025 mm

400 kHz

0,025 mm

± 0,15 %

± 1 % (Temperature drift internal compensated,

± 0,15 %

± 1 % (Temperature drift internal compensated,

detection zones

for different objects:

The dark grey areas are determind

with a thin round bar (10 or 27 mm dia.)

and indicate the typical operating range

of a sensor. In order to obtain the light grey

areas, a plate (500 x 500 mm) is introduced

into the beam spread from the side.

In doing so, the optimum angle between

plate and sensor is always employed.

This therefore indicates the maximum

detection zone of the sensor.

It is not possible to evaluate ultrasonic

reflections outside this area.

opperating voltage UB

voltage ripple

may be deactivated1), 0,17%/K without compensation)

9 V to 30 V DC, reverse polarity protection, Class 2

±10 %

9 V to 30 V DC, reverse polarity protection, Class 2

±10 %

200 kHz

0,18 mm

120 kHz

0,18 mm

± 0,15 %

± 1 % (Temperature drift internal compensated,

± 0,15 %

± 1 % (Temperature drift internal compensated,

80 kHz

0,18 mm

± 0,15 %

± 1 % (Temperature drift internal compensated,

may be deactivated1), 0,17%/K without compensation)

9 V to 30 V DC, reverse polarity protection, Class 2

±10 %

9 V to 30 V DC, reverse polarity protection, Class 2

±10 %

may be deactivated1), 0,17%/K without compensation)

9 V to 30 V DC, reverse polarity protection, Class 2

±10 %

no-load supply current

housing

≤80 mA

Brass sleeve, nickel-plated, plastic parts: PBT, TPU;

≤80 mA

Brass sleeve, nickel-plated, plastic parts: PBT, TPU;

Ultrasonic transducer: polyurethane foam,

epoxy resin with glass content

Ultrasonic transducer: polyurethane foam,

epoxy resin with glass content

class of protection to EN 60529

norm conformity

type of connection

controls

IP 67

EN 60947-5-2

IP 67

EN 60947-5-2

5-pin initiator plug, PBT

2 push-buttons (TouchControl)

5-pin initiator plug, PBT

2 push-buttons (TouchControl)

≤80 mA

Brass sleeve, nickel-plated, plastic parts: PBT, TPU;

≤80 mA

Brass sleeve, nickel-plated, plastic parts: PBT, TPU;

Ultrasonic transducer: polyurethane foam,

epoxy resin with glass content

Ultrasonic transducer: polyurethane foam,

epoxy resin with glass content

≤80 mA

Brass sleeve, nickel-plated, plastic parts: PBT, TPU;

Ultrasonic transducer: polyurethane foam,

epoxy resin with glass content

IP 67

EN 60947-5-2

IP 67

EN 60947-5-2

5-pin initiator plug, PBT

2 push-buttons (TouchControl)

5-pin initiator plug, PBT

2 push-buttons (TouchControl)

IP 67

EN 60947-5-2

5-pin initiator plug, PBT

2 push-buttons (TouchControl)

indicators

programmable

operating temperature

storage temperature

3-digit LED-display, 2 three-colour LEDs

Yes, with TouchControl and LinkControl

3-digit LED-display, 2 three-colour LEDs

Yes, with TouchControl and LinkControl

-25°C to +70°C

-40°C to +85°C

-25°C bis +70°C

-40°C bis +85°C

Weight

switching hysteresis1)

switching frequency1)

response time1)

150 g

3 mm

150 g

5 mm

25 Hz

32 ms

12 Hz

64 ms

3-digit LED-display, 2 three-colour LEDs

Yes, with TouchControl and LinkControl

3-digit LED-display, 2 three-colour LEDs

Yes, with TouchControl and LinkControl

-25°C bis +70°C

-40°C bis +85°C

-25°C bis +70°C

-40°C bis +85°C

3-digit LED-display, 2 three-colour LEDs

Yes, with TouchControl and LinkControl

-25°C bis +70°C

-40°C bis +85°C

150 g

20 mm

210 g

50 mm

8 Hz

92 ms

4 Hz

172 ms

270 g

100 mm

3 Hz

240 ms

time delay before availibility

order No.

switched output

< 300 ms < 300 ms

mic+25/D/TC

pnp, UB- 2 V, Imax = 200 mA

mic+35/D/TC

pnp, UB- 2 V, Imax = 200 mA

order No.

switched output

switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof

mic+25/E/TC

npn, -UB+ 2 V, Imax = 200 mA

mic+35/E/TC

npn, -UB+ 2 V, Imax = 200 mA

< 300 ms < 380 ms

mic+130/D/TC

pnp, UB- 2 V, Imax = 200 mA

mic+340/D/TC

pnp, UB- 2 V, Imax = 200 mA

< 450 ms

mic+600/D/TC

pnp, UB- 2 V, Imax = 200 mA

switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof

mic+130/E/TC

npn, -UB+ 2 V, Imax = 200 mA

mic+340/E/TC

npn, -UB+ 2 V, Imax = 200 mA

switchable NOC/NCC, short-circuit-proof

mic+600/E/TC

npn, -UB+ 2 V, Imax = 200 mA

1) Can be programmed with TouchControl and LinkControl

switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof

+UB

-UB

Sync/Com

1 pnp switched output

+UB

-UB

Sync/Com

1 npn switched output

mic+25…

mic+35…

mic+130…

mic+340…

mic+600…

0 cm

5 cm

10 cm

15 cm

20 cm

25 cm

30 cm

35 cm

Plate

Round bar

10 cm

5 cm

0 cm

5 cm

10 cm

0 cm

10 cm

20 cm

30 cm

40 cm

50 cm

60 cm

Plate

Round bar

20 cm

10 cm

0 cm

10 cm

20 cm

35 cm

0 m

0,4 m

0,8 m

1,2 m

1,6 m

2 m

1,3 m

Plate

Round bar

0,8 m

0,4 m

0 m

0,4 m

0,8 m

0 m

0,8 m

1,6 m

2,4 m

3,2 m

4 m

4,8 m

5,6 m

3,4 m

Plate

Round bar

1,6 m

0,8 m

0 m

0,8 m

1,6 m

0 m

1,2 m

2,4 m

3,6 m

4,8 m

6 m

7,2 m

8,4 m

Plate

Round bar

2,4 m

1,2 m

0 m

1,2 m

2,4 m

microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T+49 231 975151-0 / F+49 231 975151-51 / E[email protected] / Wmicrosonic.de

The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features.

Länna, S-142 50 SKOGÅS

Stockholm, Sweden Ordertel 08-771 00 04

Orderfax 08-771 62 00 Växel 08-771 02 20

Teknisk 08-771 35 80

Email [email protected]

Internet www.hemomatik.se

Questo manuale è adatto per i seguenti modelli

Altri manuali Microsonic Sensore di sicurezza