Microtec XT5830 HS Manuale di istruzioni

Install Software

I49-005063 A, April 2015

Start Here

Installing your Microtek XT5830 HS, XT5820 HS and

XT5810 HS Scanner

Unpack Contents

Important: You must install software before

connecting your scanner.

Always close any open programs and turn off Anti-

virus utilities before installing software.

Unpack your scanner package and check for

major components.

1. Scanner

2. Hi-Speed USB cable

3. Software CDs/DVDs

4. Power cord

5. Power adapter

A. Turn on your computer.

B. Place the Microtek Software CD/DVD into a drive, and follow the on-screen

instructions to install the scanner driver and software.

C. Restart your computer at the end of all software installation.

NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the

following in succession: “My Computer”; the CD/DVD-ROM icon; then cdsetup.exe to start the

installer program.

Connect Scanner

Customize the Function Button

Scan/Cancel

button

Power button

Scan/Cancel button: Start scan

immediately or cancel a ongoing

scan job.

Your scanner is equipped with one Scan/

Cancel button, used to automate a number of

customized and predened operations, such

as scanning to a le, sending an image to your

printer, scanning for OCR, etc. Customizing

is done through the Scanner Button Settings

interface in the ScanWizard DI, refer to the

scanner’s User’s Manual for more details.

To the power adapter

A. Connect the power adapter to the back of the scanner.

B. Plug one end of the power cord into the power adapter, and plug the other end of the

power cord into a wall outlet or other power source.

To the Hi-Speed USB cable

C. Connect one end of the cable to your computer.

D. Connect the other end of the cable to the scanner’s USB port.

E. Press and hold the Power button ( ) for a while. Once the scanner is powered on, the

Scan/Cancel button will be lighted up in green and the system will detect the scanner

automatically.

Positioning Documents

1. Raise the scanner lid.

2. Place the document to be scanned facing down on the glass surface of the scanner.

Position the top end of the document toward the left side of the scanner, with its edge

rmly aligned against the vertical ruler of the scanner (shown in the graphic below).

3. Lower the scanner lid.

To scan a single-sheet of document:

With the document facing down on the

glass surface of the scanner, align the

document along the vertical ruler and

set it to the Arrow mark ( )on the

upper left corner of the scanner’s glass

surface.

To scan a book or thick documents:

You may lift up the scanner lid out

from its hinge sockets. Then, align the

inner margin of a book along the side

of the glass surface of the scanner as

indicated in the graphic.

Scanning Documents

1. Put the document to be scanned facing down on the scanner’s scan bed.

2. Launch ScanWizard DI as a stand-alone program by clicking on the ScanWizard DI icon

on the desktop.

3. Click the Scan Setup button in the interface to activate the Scan Setup interface.

4. In the Scan Setup interface, follow the steps below to specify your basic settings.

a) Select Flatbed in the Scan Source as your image input

device.

b) Select the appropriate image type in the Color Mode as

your image output type.

– Select RGB Color (24 bits) to scan the image in color.

– Select Grayscale (8 bits) to scan the image in

grayscale.

– Select Black & White (1 bit) to scan the image in

black-and-white.

– Select Auto Color Detection to scan the image in color or non-color based on

the automatic judgement and detection of the system.

– Select Complex to scan the image in color, grayscale or non-color based on the

customization.

c) Select a dimension in the Paper Size as your preview

image size.

d) Select a desired resolution in the Resolution for your

image output resolution.

e) If “Auto-crop” & “Auto-deskew” is selected, the scanner

automatically detects the size of the original image,

crops the full scan frame to t the image, and removes

unwanted black borders after the scan, as well as corrects

the distorted image for proper alignment.

5. Click the Show Preview Window and Show Setting Window tabs in the Scan Setup

interface to display other interfaces which are helpful for your scanning processing.

6. Click the Preview button to perform a preliminary view of the entire image. When

done, a preview image appears in the Preview window.

7. Go to the “General” panel by clicking the General tab in the Settings window. Specify

the settings for your requirements there.

a) Select the image type in the Document Type as your input image type.

– Select Photo to scan color prints.

– Select Text to scan text.

b) If necessary, check “Remove Blank Page” and “Remove

Punch Hole” to enhance the quality of the scanned

images.

8. If necessary, go to the “Image Process” panel by clicking the Image Process tab in

the Settings window. Use the image correction tools presented there to enhance the

image quality according to your specic requirements.

9. Click the OK button to close the Scan Setup interface and return to the Main interface

of ScanWizard DI.

10. In the Main interface, click the File Format menu button to select a le format for the

scanned images.

11. In the Main interface, click the File Name menu button to specify a le naming method

for the scanned images.

12. In the Main interface, select and click the Normal Scan button to start scanning.

When done, the scanned images will be automatically saved into the folder dened in

the File Location menu box. At the same time, the scanned images will be displayed

in thumbnail sizes in the Thumbnail View window and labeled with the le name and

le format specied earlier.

13. Click the Open Folder button to locate the scanned images if you want to view.

NOTE: For more details on other scanning scenarios applicable to your scanner, refer to the

scanner’s User’s Manual in the Microtek Software CD/DVD.

AP control panel (Main interface)

TWAIN driver control panel

(Scan Setup interface)

File Location

menu box

Click on a

thumbnail image

to enlarge it in

the Image View

Window at the

right side of the

interface.

Problems?

The Multi-color LED on the button indicates the status of the scanner.

First, make sure that you have followed Steps 1 to 3 as described in this guide (unpack,

install, connect). Then if your problem is listed here, try the suggested solution.

1. No light comes on when the scanner is turned on.

Make sure your scanner is connected to your computer and plugged into a power

source.

Make sure your scanner is detected by your computer.

2. The Add/Remove Hardware Wizard appears on your screen.

Click the “Cancel” button and close the ScanWizard DI Control Panel.

Disconnect the Hi-Speed USB cable from the back of your computer, and refer to the

installation instructions in this document.

3. When trying to scan, an error message appears on your screen that reads, “Can’t Find

Scanners”.

Make sure your scanner is connected to your computer and plugged in to a power

source (see Step 3).

Uninstall and reinstall the ScanWizard DI software.

4. After clicking “Scan,” a blank screen appears.

Uninstall and reinstall the ScanWizard DI software.

LED

Off: Scanner is off

Green On: Ready to scan

Flashing Green: Scanning or sleeping

Red On: Error or USB disconnecting

when powered up

DoYou Need Assistance?

Manuals

If you have additional questions and need further instruction or information, we provide

electronic manuals for:

1. Using your scanner (scanner’s User’s Manual)

2. Using the ScanWizard DI

To access the electronic manuals: Insert the scanner’s software CD/DVD into your

computer’s CD/DVD-ROM drive. Next, locate and click the “Manuals” option when the

software installer window appears on your screen. Finally, select and click the title of the

manual you wish to view.

Missing Items

If your package is missing items, please call the Microtek Customer Service Department.

Drivers & Software Upgrades

After you nish the installation of software, if you found that the installed drivers and

software cannot run your product or your computer system properly later, please go to the

Microtek Download Service site at ww7.microtek.com.tw/service.php to download and

install any updates you may require.

For additional information about Microtek products, please visit our website at www.

microtek.com.

ColoRescue are trademarks or registered trademarks of Microtek International,

Inc. All other trademarks or registered trademarks are the property of their

respective holders. Specications, software and hardware bundles are subject to

change without notice. Delivery of technical support services subject to change

without notice. Not responsible for typographical errors.

Power Adapter

Use only power supplies (AC/DC adapters) listed below:

Voltage Manufacturer Model No.

AC 100V to 240V APD DA-48M24

NOTE: Please make sure that the electrical outlet to where the scanner will be

connected is nearby and readily accessible.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Microtec Scanner

Microtec

Microtec Bio-1000F Manuale utente

Manuali Scanner popolari di altre marche

Plustek

Plustek Scanner Manuale utente

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuale utente

Renkforce

Renkforce DS100-5M Manuale utente

Image Access

Image Access WideTEK A2 Manuale utente

Canon

Canon imageFORMULA CR-120N Manuale utente

Fujitsu

Fujitsu FI-4860C2 Manuale utente

GeoSlam

GeoSlam ZEB Horizon Istruzioni per l'installazione

Kodak

Kodak i5800 Scanner Manuale utente

Kodak

Kodak i7300 Manuale utente

Revopoint

Revopoint POP Manuale utente

Fujitsu

Fujitsu fi-4860C Manuale utente

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuale utente

Faselase

Faselase F6 Manuale utente

Fujitsu

Fujitsu CardMinder Manuale utente

Uniden

Uniden BC340CRS Manuale utente

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuale utente

Mustek

Mustek PageExpress 4800 Pro Manuale utente

Optex

Optex 750830 Manuale utente