Middleby Marshall Oven Manuale utente
2-1
SECTION 2
INSTALLATION
WARNING
Do not obstruct the flow of combustion
and ventilation air to and from your
oven. There must be no obstructions
around or underneath the oven.
I. UNLOADING/UNPACKING
YourMiddlebyMarshallOvensareshippedpartiallyassembled.
Each oven section will arrive in its own crate of the following
size and weight:
PS360U/PS360L PS360WB-U/PS360WB-L
Length: 72 (183cm) 66 (167cm)
Width: 48 (122cm) 57 (144cm)
Height: 60 (152cm) 50 (127cm)
Weight: 1675 lbs. (760kg) 1750 lbs. (780kg)
If you ordered stands for your ovens, they are shipped in
separate crates.
When your common carrier or truck line notifies you of delivery,
you must have a forklift at the facility to unload the crate(s).
If you have a door that is wider than the ovens, simply move the
ovens into your facility and set up an appointment with your
Middleby Marshall Authorized Installer.
NOTE: The width of each oven can be reduced by about 1"
(25mm) by removing the window from the oven. Window
disassembly instructions are in the Cleaning section of this
Owners Manual.
If the ovens are wider than your door opening, the oven will
have to be dismantled according to the directions in the Pre-
Installation Procedures Manual.
SECTION 2
INSTALLATION
NOTE
There must be adequate clearance
between the oven and combustible con-
struction. Clearance must also be pro-
vided for servicing and for
operation.
WARNING
This oven must be installed in accordance
with the rules in force. Use only in a
well ventilated area. Read the
instructions before use.
2-2
SECTION 2
INSTALLATION
2"
51mm
Minimum
18"
458mm
18"
458mm 12"
305mm 3”
76mm
II. INSTALLATION, PREPARATION, AND
SUPPLY
When preparing the oven for installation at a location, the latest
International, National or Local Requirements should be
adhered to.
The ovens must be installed on an even (level) non-flammable
flooring and any adjacent walls must be non-flammable. The
minimum allowed distance from the rear of the oven to the wall
is 12 (30cm).
The ovens can be supported only by legs. No casters are
allowed. Itshouldbemadecertainthattherearenoobstructions
located around or underneath the oven that interfere with air
circulation.
The ovens must be installed under a ventilating hood with
electrical exhaust air sensing control.
The gas supply connection should be according to applicable
ISO-228-1 or ISO-7-1 recommendations.
Normally, the oven is preparted and adjusted to the specific
gas type used by the customer. Before operating the oven,
check the label on the oven and also on the packaging that the
gas type indicated matches the local supply at the installation.
If not, refer to Section VI, PREPARATION FOR VARIOUS
GASES, in this chapter and convert as directed.
All installations, conversions and service work must be
performed by an Authorized Service Agent according to the
instructions supplied by the manufacturer.
When converting from one gas type to a different type, the
orifices supplied with the conversion kit must be checked for
proper size as specified in this manual to assure that the oven
is operating at the nominal rated input.
Figure 2-1 - Ventilation Hood Dimensions (RECOMMENDATIONS ONLY)
2-3
SECTION 2
INSTALLATION
III. VENTILATION SYSTEM
IMPORTANT
Where international, national, or local codes require
the installation of fire suppression equipment or other
supplementary equipment, DO NOT mount the
equipment directly to the oven.
MOUNTING SUCH EQUIPMENT ON THE OVEN MAY:
VOID AGENCY CERTIFICATIONS
RESTRICT SERVICE ACCESS
LEAD TO INCREASED SERVICE EXPENSES FOR
THE OWNER
REQUIREMENTS
A mechanically driven ventilation system is required for the
oven.
PROPER VENTILATION OF THE OVEN IS THE
RESPONSIBILITY OF THE OWNER.
RECOMMENDATIONS
NOTE THAT THE HOOD DIMENSIONS SHOWN IN FIG-
URE 2-1 (PREVIOUS PAGE) ARE RECOMMENDATIONS
ONLY. INTERNATIONAL, NATIONAL, AND LOCAL
CODES WILL VARY, AND MUST BE FOLLOWED WHEN
INSTALLING THE VENTILATION SYSTEM. ANY AP-
PLICABLE INTERNATIONAL, NATIONAL, AND LOCAL
CODES SUPERSEDE THE RECOMMENDATIONS
SHOWN IN THIS MANUAL.
The rate of air flow exhausted through the ventilation system
may vary depending on the oven configuration and hood
design. Consult the hood manufacturer or ventilation engineer
for these specifications.
To avoid a negative pressure condition in the kitchen area,
return air must be brought back to replenish the air that was
exhausted. A negative pressure in the kitchen can cause heat-
related problems to the oven components as if there were no
ventilation at all. The best method of supplying return air is
through the heating, ventilation and air conditioning (HVAC)
system. Through the HVAC system, the air can be temperature-
controlled for summer and winter. Return air can also be
brought in directly from outside the building, but detrimental
affects can result from extreme seasonal hot and cold
temperatures from the outdoors.
NOTE: Return air from the mechanically driven system must
not blow at opening of bake chamber. Poor oven baking
performance will result.
OTHER VENTILATION CONCERNS
Special locations, conditions, or problems may require the
services of a ventilation engineer or specialist.
Inadequate ventilation can inhibit oven performance.
It is recommended that the ventilation system and duct
work be checked at prevailing intervals as specified by the
hood manufacturer and/or HVAC engineer or specialist.
2-4
SECTION 2
INSTALLATION
PS360L/WB-L Tandem
PS360/WB Double Tandem
PS360U/WB-U Tri Tandem
Item Part # Description PS360U/WB-U Quad Tandem
1 22361-0001 Flexible Gas Hose 2 4 3 4
2 22450-0028 Adjustable Legs 8 8 12 16
3 30773 Flue Vent, 14"Lg. 2 - - -
4 30759 Flue Vent, 29-1/2"Lg. - 2 3 4
5 30758 Flue Vent, 50" Lg. - 2 - -
6 21256-0008 Screw, 10-32 x 3/8 A/R A/R A/R A/R
8 42400-0089 Master Link Kit, PS360
8 42400-0598 Master Link Kit, PS360WB
9 35122-0049 Attachment Strip - 4 - -
10 35000-1103 Stop, End Conv., PS360
10 35000-1899 Stop, End Conv., PS360WB
11 21292-0001 Scr, #2PT 10-16 x 3/4 Hx Wsh A/R A/R A/R A/R
12 33984 Thermocouple 2 4 3 4
13 27276-0001 Cable Clamp 2 4 3 4
14 1002040 Warranty,Parts & Serv. Dist.List 1 1 1 1
15 38615 Owners Manual,English 1 1 1 1
16 27126-0238 11 Piece Hex Key Set 1 1 1 1
17 31389 Silicone Tubing, 36 (914mm) L x
5/16 (8mm) ID x 7/16 (11mm) OD 2 4 3 4
- 35000-1454
Machinery Compartment Trim Strip
1222
- 35000-1456 Front Gasket Spacer 2 4 4 4
- 35000-1457 Rear Gasket Spacer 2 4 4 4
- 37200-0013
Baking Chamber Gasket and Frame
1222
- 37000-0696 Transition Floor Panel - - - 1
- 48009-0024 Transition Top Panel - - - 1
- 48009-0025 Transition Side Wall - - - 2
- 35000-1748 Transition Rear Support - - - 1
- 35000-1749 Transition Front Support - - - 2
- 37000-0697 Transition Top Support Channel - - - 2
2434
12 --
Figure 2-2 - INSTALLATION KIT
2-5
SECTION 2
INSTALLATION
6”
152mm
10-1/2”
267mm
16-1/2"
419mm
11-1/2"
292mm
27-1/4"
692mm 27-1/4"
692mm
54-1/2"
1384mm
17-3/4"
451mm
31-1/2"
800mm
45-1/2"
1156mm
144-1/2"
3670mm
109"
2769mm
17-3/4"
451mm
42"
1067mm
40"
1016mm
6-1/2"
165mm
45"
1143mm
42-3/4"
1086mm
44
1
2
1
2
2”
51mm
3
32”
813mm
16-1/2"
419mm
11-1/2"
292mm
27-1/4"
692mm 27-1/4"
692mm
54-1/2"
1384mm
6”
152mm
10-1/2”
267mm
31-1/2"
800mm
6-1/2"
165mm
45-1/2"
1156mm
144-1/2"
3670mm
109"
2769mm 17-3/4"
451mm
17-3/4"
451mm 50-3/4”
1289mm
50"
1270mm
48"
1219mm
53"
1346mm
44
1
2
1
2
2”
51mm 3
40”
1016mm
Figure 2-3
Dimensions and Data: PS360L Tandem
Figure 2-4
Dimensions and Data: PS360WB-L Tandem
2-6
SECTION 2
INSTALLATION
34"
864mm
16-1/2"
419mm
11-1/2"
292mm
27-1/4"
692mm 27-1/4"
692mm
54-1/2"
1384mm
5-27/32"
148mm
10-1/8"
258mm
6-1/4"
158mm
11-1/2"
292mm
31-1/2"
800mm
6-1/2"
165mm
144-1/2"
3670mm
109"
2769mm 17-3/4"
451mm
17-3/4"
451mm
52"
1321mm
81-1/2"
2070mm
2”
51mm
42"
1067mm
40"
1016mm
45"
1143mm
3
44
13
1
2
1
2
1
2
1
2
32”
813mm
Figure 2-5
Dimensions and Data: PS360 Double Tandem
Figure 2-6
Dimensions and Data: PS360WB Double Tandem
2-7
SECTION 2
INSTALLATION
Figure 2-7
Dimensions and Data: PS360U Tri Tandem
2-8
SECTION 2
INSTALLATION
Figure 2-8
Dimensions and Data: PS360WB-U Tri Tandem
2-9
SECTION 2
INSTALLATION
Figure 2-9
Dimensions and Data: PS360U Quad Tandem
2-10
SECTION 2
INSTALLATION
Figure 2-10
Dimensions and Data: PS360WB-U Quad Tandem
Questo manuale è adatto per i seguenti modelli
4
Altri manuali Middleby Marshall Forno
Middleby Marshall
Middleby Marshall PS636 series Manuale operativo
Middleby Marshall
Middleby Marshall PS629G Series Manuale operativo
Middleby Marshall
Middleby Marshall PS2620 Series Manuale utente
Middleby Marshall
Middleby Marshall PS528 (Double) Manuale operativo
Middleby Marshall
Middleby Marshall PS200VL Manuale operativo
Middleby Marshall
Middleby Marshall PS200 series Manuale operativo
Middleby Marshall
Middleby Marshall PS314 Manuale operativo
Middleby Marshall
Middleby Marshall PS360 SERIES Manuale operativo
Middleby Marshall
Middleby Marshall PS520 Series Manuale operativo
Middleby Marshall
Middleby Marshall PS528G Manuale operativo
Middleby Marshall
Middleby Marshall PS360WB70-L Manuale utente
Middleby Marshall
Middleby Marshall CTX DZ26T Series Manuale operativo
Middleby Marshall
Middleby Marshall PS500 Series Manuale operativo
Middleby Marshall
Middleby Marshall CTX DZ33T Series Manuale operativo
Middleby Marshall
Middleby Marshall PS300F Manuale operativo
Middleby Marshall
Middleby Marshall PS200 series Manuale operativo
Middleby Marshall
Middleby Marshall PS636G Manuale operativo
Middleby Marshall
Middleby Marshall PS200 Tandem Manuale utente
Middleby Marshall
Middleby Marshall PS670 Manuale operativo
Middleby Marshall
Middleby Marshall PS360E Series Manuale operativo
