Mikra M15 Manuale utente

HFCE

mikra

TABLE OF CONTENTS

OPERATION OVERVIEW AND GENERAL INTRODUCTION ..................................... 1

INTRODUCTION .......................................................................................................... 2

MANUAL MODE .......................................................................................................... 3

SINGLE MODE ............................................................................................................ 3

PRE-SET PROGRAM (10 SETS)................................................................................. 4

PROGRAM LOCK AND OPEN(10 SETS) ................................................................... 5

FAST PROGRAM......................................................................................................... 6

FINE ADJUSTMENT .................................................................................................... 6

LOAD DATUM VALUES............................................................................................... 7

SELECT COUNTING DIRECTION(+/-) ........................................................................ 8

RESOLUTION .............................................................................................................. 9

SENSOR CALIBRATION ........................................................................................... 10

SET PARAMETER ..................................................................................................... 11

PARAMETER ............................................................................................................. 12

PARAMETER LOCK AND OPEN .............................................................................. 13

TROUBLESHOOTING ............................................................................................... 14

INSTALLATION GUIDE ............................................................................................. 16

POWER SUPPLY & HARDWARE ............................................................................. 18

EXTERNAL DIMENSION ........................................................................................... 19

Operation Panel

LED / KEY Description KEY Description KEY Description

Upper Window

Target value

Manual / Single

mode Parameter

Upper LED Target value

LED Program mm / inch

Lower Window

Current value

Active Clear / Return

Lower LED Current value

LED Stop / Cancel

Confirm / Enter

0 ~ 9 Number keys

+ / - Decimal

Note: Display : LED on / blinks

Upper Window

Lower Window LED lamp

Introduction

Function:

One or two speed positioning 7. Resolution: 0.1mm/ 0.05mm/ 0.01mm

Manual / Single mode 8. Correct zero point

10 sets single program 9. Display: RPM speed

10 sets tool offsets 10.

Protection for tool / motor fault

Quick program / Fine Adjustment 11.

Battery life 2.5 year

Inch / mm conversion 12.

Self-diagnose

Specification:

Housing: 115w ×115h ×80d (mm)

Panel cut out: 93w ×67h (mm)

Mounting screws: M3 ×4 104 ×104 (mm)

Supply voltage: 24VDC/50mA/, C type battery (1.5V) ×1

Battery voltage control: Low battery alarm

Sensor cable length: 3m

Thermal expansion: α= 16 ×10

-6

×1/K

Gap sensor/strip: max. 2.5mm

Display: 15mm LED ×6 digits ×2 line

Output: 4 digital output

(AC250V / 7A;DC24V/10A）

Input: 4 digital input（24VDC）

Operating elements: 20 button keyboard

Test mark/ interfere

.Protection class: 3 accord. to IEC 801

Travel Speed: 1.5m/s

System accuracy: ±(0.025+0.02L)mm, L: Meter）

Repeatability: 0.01mm

Temperature: Operating temperature 0 + 50, Storage temperature –20

+70℃

Humidity: max. 95% rF(Condensation not permitted）

Manual Mode

Description: To move the machine table by pressing M15 keyboard.

fast forward backward fast

Example: M15 displays 100.00mm, to move the machine table:

Note: Be sure in “※manual” mode. (LED lamp of “manual / Single” key is blinking) The

upper window shows “HAnd” mode.

Press to move machine table forward

(fast).

Press to move machine table backward (fast).

Note: Press or for forward/ backward/

lower speed (depends on machine and wiring).

Single Mode

Description: M15 can execute auto positioning.

Example: M15 current value is 100.00mm, to reach 200mm (setting target value).

Step1. Select single mode LED lamp is off.

Step2. Press , blinking, enter new target

value

LED lamp is off, complete.

※Note: During positioning, press to stop;

to re-start, press and

100.00

200.00

100.00

STOP

PROG

2 0 0

= H A n d

106.80

H A n d =

96.80

Pre-Set Program (10 sets)

Description: Pre-set program 10 sets, enter program # 0~9 to execute.

Example: Program 1=10mm, Program 2=20.00mm.

Step1. Press

select enter a key (0-9, total of 10sets).

Note: Be sure in manual mode.※

Step2. (Enter program 1=10mm), press

more press .

Step3. Target value display: ProG＿at present,

enter program 2=20.00mm, press to

exit.

ProG

F 5 5

1 0

Program Open and Lock (10 sets)

Description: Don’t needs pre-set program, to start or close.

Example: Program 1=10.00mm for , program 2= 20.00mm for ,

~ other a key, don’t setting pre-set program, to stop follow

steps as below:

Step1. Press

target value display: ProG_ .

Note: Be sure in single mode.※

Step2. Press

current value display:_ _ _ _ _ _, closed,

frame display, started.

Step3. Press to close

※Note: To close other keys, follow the step 2, 3.

0 1

５

５５

５

５５

５

STOP

20.00

ProG

START

Fast Program

Description: To facilitate frequently used positions, the keys 0 to 9 have associated

preset target values. And the positioning can be started immediately.

Example: Program 1=10.00mm, program 2=20.00mm. Execute program 2 as below:

Step1. Select singe mode LED lamp off.

Step2. Press target value display: 20.00mm

LED blinking, to waitting start.

※Note: Execute program1 press#1.

Fine Adjustment

Description: Increase and decrease to reach fine adjustment.

Example: M15 target value display100.78mm, increase/ decrease target value0.25mm,

setting steps as below:

Step1. Increase target value: press

display 0.00 LED blinking,

decrease: press twice,

display-0.00 LED blinking.

Step2. Press

press to completed.

※Note: Target value display: 101.03mm, current value

display:100.78mm for target value increase

0.25mm.

50 2

+/-

100.00

20.00

100.00

0.00

100.00

0.25

Load datum values

A. Description: To load current value according to working piece.

Example: M15 current value display100.00mm, actual size: 100.50mm, follow the

steps as below:

Step1. Select singe mode LED lamp off.

Step 2. Press , enter new

value, press

press , to exit.

B. How to show the new set value:

Step1. Press , press twice,

display new value.

100.00

OriGin

100.00

F 0

100.00

1 0

0 5

F 0

Select Counting Direction(+/-)

Description：To select the counting direction.

Example：M-15 current value display: 100.00mm, sensor forward for decrease value

99.68mm, but hope value become big, value increase follow the steps as

below:

Step1. Press back single mode, LED lamp off.

Step 2. Press

target value display origin parameter value “-dir”

(select counting direction parameter).

Step 3. Press to select the direction, -dir / dir

(or"-dir" for left or "dir- " for right.)

Step 4. Press to complete, and exit.

100.00

99.68

F 1

99.68

dir

100.00

99.68

PROG

Altri manuali per M15

Indice

Altri manuali Mikra Controllori

Mikra

Mikra M15 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente