MikroTik R11e-LTE-US Manuale utente

1 / 10

□Normal □Internal Use Confidential □Restricted Confidential

R11e-LTE-US User Manual

OEM/Integrators Installation Manual

2 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

Important Notice to OEM integrators

1. This module is limited to OEM installation ONLY.

2. This module is limited to installation in mobile or fixed applications, according to Part

2.1091(b).

3. The separate approval is required for all other operating configurations, including portable

configurations with respect to Part 2.1093 and different antenna configurations

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how

to install or remove this RF module in the user’s manual of the end product which integrates

this module. The end user manual shall include all required regulatory information/warning as

show in this manual.

CAN ICES-3(B)/ NMB-3(B)

Innovation, Science and Economic Development Canada

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the

following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement."

3 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

For class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

—Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment. This transmitter must not be

co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement

This equipment complies with FCC/IC RF exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20 cm

between the radiator & your body.

4 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de

20 cm de distance entre la source de rayonnement et votre corps.

End Product Labeling

The host system using this module must display a visible label indicating the following text:

Contains FCC ID: TV7R11ELTE

The host system using this module must display a visible label indicating the following text:

Contains IC: 7442A-R11ELTE

This device is intended only for OEM integrators under the following conditions:

(1) The antenna must be installed such that 20 cm is maintained between the antenna and

users,

(2) The transmitter module may not be co-located with any other transmitter or antenna

(3) To comply with FCC/IC regulations limiting both maximum RF output power and human

exposure to RF radiation, the maximum antenna gain including cable loss in a mobile exposure

condition must not exceed:

。-3.5 dBi in 700 MHz Band

。-3.5 dBi in 850 MHz Band

。0.6 dBi in 1700 MHz Band

。0.6 dBi in 1900 MHz Band.

In the event that these conditions cannot be met (for example certain laptop configurations or

co-location with another transmitter), then the FCC/IC authorization is no longer considered

valid and the FCC/IC ID cannot be used on the final product. In these circumstances, the OEM

integrator will be responsible for re-evaluating the end product (including the transmitter) and

obtaining a separate FCC/IC authorization

5 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

Contents

Contents..........................................................................................................................5

1. Introduction ............................................................................................................6

1.1. Features................................................................................................................ 6

2. Electrical Specification.............................................................................................6

2.1. Power supply........................................................................................................ 6

3. RF Specifications .....................................................................................................7

3.1. RF Specification .................................................................................................... 7

3.2.1 Band support................................................................................................. 7

3.2.2 Bandwidth support........................................................................................ 7

3.2.3 RF Transmit Specification .............................................................................. 7

3.2.4 RF Receiver Specification .............................................................................. 8

4. Mechanical and Environmental Certifications ..........................................................8

4.1. PCBA Form Factor................................................................................................. 8

4.2. Thermal considerations...................................................................................... 10

6 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

1. Introduction

The R11e-LTE-US mini-PCIe module is a Cat. 4 LTE modem which integrates an application CPU

subsystem, peripheral interfaces and functions designed to address the power/

performance/cost requirements of IoT and M2M applications. The CPU is based on

Qualcomm’s MDM architecture which offers OFDMA-related software based signal processing

capabilities that significantly exceed traditional communications ARM cores. R11e-LTE-US

module provides a variety of interfaces including USB 2.0, PCM, UART, USIM .

1.1. Features

LTE Cat. 4 with 150/50 Mbps for DL/UL

Supports LTE B2/4/5/12, 3GPP release 10 without Carrier Aggregation

Supports WCDMA 2/5, 3GPP release 8

Ultra-high-performance Cortex A7 microprocessor

Modem subsystem (MSS)

Resource and power management (RPM) subsystem

Optimized for M2M and IoT markets

Interfaces

–Host USB 2.0 with integrated PHY

–USIM interface

–PCM

–UART

2. Electrical Specification

2.1. Power supply

LTE module power input is 3V3.

Power

Pin Name

Pads

Description

Voltage Level (V)

Min.

Typ.

Max.

3V3

Main Power Supply

3.2

3.3

3.6

7 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

3. RF Specifications

3.1. RF Specification

3.2.1 Band support

Table 1. Band support

Band

Uplink (MHz)

Downlink (MHz)

LTE Band 2

1,850–1,910

1,930–1,990

LTE Band 4

1,710–1,755

2,110–2,155

LTE Band 5

824–849

869–894

LTE Band 12

699–716

729–746

Band

Uplink (MHz)

Downlink (MHz)

WCDMA Band 2

1,850–1910

1,930–1,990

WCDMA Band 5

824–849

869–894

3.2.2 Bandwidth support

Table 2. Bandwidth support

Band

Bandwidth

1.4 MHz

3 MHz

5 MHz

10 MHz

15 MHz

20 MHz

LTE Band 2



LTE Band 4



LTE Band 5



LTE Band 12



3.2.3 RF Transmit Specification

Table 3. Conductive TX output power

Band

Items

Parameter

Unit

Min.

Typ.

Max.

LTE Band 2

Max. TX Power

10 MHz 12 RBs/QPSK

dBm

20.3

25.7

LTE Band 4

Max. TX Power

10 MHz 12 RBs/QPSK

dBm

20.3

25.7

LTE Band 5

Max. TX Power

10 MHz 12 RBs/QPSK

dBm

20.3

25.7

LTE Band 12

Max. TX Power

10 MHz 12 RBs/QPSK

dBm

20.3

25.7

Band

Items

Parameter

Unit

Min.

Typ.

Max.

8 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

WCDMA Band 2

Max. TX power

dBm

20.3

23.5

25.7

WCDMA Band 5

Max. TX power

dBm

20.3

23.5

25.7

3.2.4 RF Receiver Specification

Table 4. Conductive Rx sensitivity-3GPP

Band

Items

Parameter

Unit

Min.

Typ.

Max.

LTE Band 2

RX Sensitivity

10 MHz with 50 RBs

dBm

–101

–94.3

LTE Band 4

RX Sensitivity

10 MHz with 50 RBs

dBm

–102

–96.3

LTE Band 5

RX Sensitivity

10 MHz with 50 RBs

dBm

–102

–94.3

LTE Band 12

RX Sensitivity

10 MHz with 50 RBs

dBm

–102

–93.3

Band

Items

Parameter

Unit

Min.

Typ.

Max.

WCDMA Band 2

RX Sensitivity

dBm

–110

–104.7

WCDMA Band 5

RX Sensitivity

dBm

–110

–104.7

4. Mechanical and Environmental

Certifications

4.1. PCBA Form Factor

R11e-LTE-US module has the dimensions as below:

50.85 mm (typ.) × 29.9 mm (typ.) × 3.3 mm (typ.), tolerance: ± 0.15 mm

9 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

Top view

Right view

Figure 1. PCBA dimension

Figure 2. PCB dimension(Bottom view)

10 / 10

R11e-LTE-US User manual

□Normal □Internal Use Confidential □Restricted Confidential

4.2. Thermal considerations

Ambient operating temperature: –25 °C to +75 °C

(–20 °C to +60 °C fully compliant with 3GPP; –25 °C to +75 °C functional work)

Ambient storage temperature: –40 °C to +85 °C

The case temperature of module shielding cover must be < 85 °C when integrated to prevent

damage.

Altri manuali per R11e-LTE-US

Indice

Altri manuali MikroTik Hardware di rete

MikroTik

MikroTik RouterBOARD 750G Manuale utente

MikroTik

MikroTik CRS354-48G-4S+2Q+RM Manuale utente

MikroTik

MikroTik hAP ax lite LTE6 Manuale utente

MikroTik

MikroTik RouterBOARD 411R Manuale utente

MikroTik

MikroTik netFiber 9 Manuale utente

MikroTik

MikroTik RAY60 Manuale utente

MikroTik

MikroTik RBM11G Manuale utente

MikroTik

MikroTik ATL LTE18 kit Manuale utente

MikroTik

MikroTik LHG 60G Manuale utente

MikroTik

MikroTik MQS Manuale utente

MikroTik

MikroTik L009UiGS-2HaxD-IN Manuale utente

MikroTik

MikroTik LHG LTE18 kit Manuale utente

MikroTik

MikroTik 2004-1G-12S+2XS Manuale utente

MikroTik

MikroTik CCR2004-16G-2S+ Manuale utente

MikroTik

MikroTik CRS310-1G-5S-4S Plus OUT Manuale utente

MikroTik

MikroTik RouterBOARD 450 Series Manuale utente

MikroTik

MikroTik RBLDF-5nD Manuale utente

MikroTik

MikroTik Woobm-USB Manuale utente

MikroTik

MikroTik Wireless Wire Manuale utente

MikroTik

MikroTik RouterBOARD 2011U Series Manuale utente

MikroTik

MikroTik RBMetalG-52SHPacn Manuale utente

MikroTik

MikroTik Chateau LTE12 Manuale utente

MikroTik

MikroTik RouterBOARD 33/433AH Manuale utente

MikroTik

MikroTik LHGGM&EG18-EA Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente