Milesight UG65 Manuale utente

Milesight IoT

Semi-industrial

LoRaWAN®Hotspot

UG65

User Guide

Safety Precautions

Milesight will not shoulder responsibility for any loss or damage resulting from not following the

instructions of this operating guide.

The device must not be modeled in any way.

Do not place the device close to objects with naked flames.

Do not place the device where the temperature is below/above the operating range.

Do not power on the device or connect it to other electrical devices when installing.

Check lightning and water protection when used outdoors.

Do not connect or power the equipment using cables that have been damaged.

Related Documents

Document

Description

UG65 Datasheet

Datasheet for UG65 LoRaWAN®Hotspot.

The related documents are available on the Milesight website: https://www.milesight-iot.com

Declaration of Conformity

UG65 conforms with the essential requirements and other relevant provisions of the CE, FCC, and RoHS.

For assistance, please contact

Milesight technical support:

Email: iot.support@milesight.com

Tel: 86-592-5085280

Fax: 86-592-5023065

Revision History

Date

Doc Version

Description

Oct. 12, 2021

V1.0

Initial version

Nov. 23, 2021

V1.1

QR Code Generate Update

Contents

1. Packing List....................................................................................................................................................4

2. Hardware Introduction................................................................................................................................. 4

2.1 Overview...............................................................................................................................................4

2.2 Dimensions.......................................................................................................................................... 5

2.3 LED Indicators..................................................................................................................................... 5

2.4 Reset Button........................................................................................................................................ 6

3. Hardware Installation................................................................................................................................... 6

3.1 SIM Card Installation.......................................................................................................................... 6

3.2 Ethernet Cable & Power Cable Installation..................................................................................... 6

3.3 Antenna Installation........................................................................................................................... 7

3.4 Hotspot Installation............................................................................................................................ 7

3.4.1 Wall Mounting.......................................................................................................................... 7

3.4.2 Pole Mounting..........................................................................................................................8

4. Login the Web GUI.........................................................................................................................................9

4.1 Wireless Access..................................................................................................................................9

4.2 Wired Access.....................................................................................................................................11

5. Network Connection................................................................................................................................... 13

5.1 Configure the Ethernet Connection................................................................................................13

5.2 Configure the Wi-Fi Connection......................................................................................................13

5.3 Configure the Cellular Connection................................................................................................. 15

6. Helium Hotspot Setup................................................................................................................................ 16

7. Antenna and Frequency Configuration.................................................................................................... 19

1. Packing List

Before you begin to install the UG65 LoRaWAN®hotspot, please check the package contents to verify

that you have received the items below.

Bracket Fixing Screws

Wall Mounting Kits

1 × Warranty Card

1 × Quick Start Guide

1 × LoRa Antenna

If any of the above items is missing or damaged, please contact your sales representative.

2. Hardware Introduction

2.1 Overview

A. Front Panel

1 × UG65

1 × Ethernet Cable

1 × DC Jack Power Adapter

1 × Mounting Bracket

1LED Area

POWER: Power Indicator

STATUS: System Indicator

LoRa: LoRa Indicator

Wi-Fi: Wi-Fi Indicator

LTE: Cellular Indicator

ETH: Ethernet Port Indicator

2LoRa Antenna Connector

B. Rear Panel

2.2 Dimensions (mm)

2.3 LED Indicators

LED

Indication

Status

Description

POWER

Power Status

Off

The power is switched off

The power is switched on

STATUS

System Status

Blue Light

Static: the system is running properly

Red Light

The system goes wrong

LoRa

LoRa Status

Off

Packet Forwarder mode is running off

Blue Light

Packet Forwarder mode is running well

Wi-Fi

Wi-Fi Status

Off

Wi-Fi is disabled

Blue Light

Wi-Fi is enabled

LTE

Cellular Status

Off

SIM card is registering or fails to register

(or there are no SIM cards inserted)

Blue Light

Blinking slowly: SIM card has been registered

and is ready for dial-up

Blinking rapidly: SIM card has been registered

and is dialing up now

Static: SIM card has been registered and dialed

3Bracket Mounting Screws

4SIM Slot

5Type-C Port

6Ethernet Port (PoE)

7Power Connector

8Reset Button

9Waterproof Silicone

10 Cable Groove

up successfully

ETH

Ethernet

Port Status

Off

Disconnected

Blue Light

Static: Connected

2.4 Reset Button

Function

Description

STATUS LED

Action

Reset

Static Blue

Press and hold the reset button for more than 5 seconds.

Static Blue →

Rapidly Blinking

Release the button and wait.

Off →Static Blue

The hotspot resets to factory default.

3. Hardware Installation

3.1 SIM Card Installation

A. Use a screwdriver to open the protective cover on the back panel of UG65.

B. Insert the SIM card into the device according to the direction icon on the device.

Note:

If you need to take out the SIM card, press into the SIM card and it will pop up automatically.

UG65 does not support hot-plugging (also called hot swapping). please turn off the power before

inserting or taking off cards.

3.2 Ethernet Cable & Power Cable Installation

A. Connect the Ethernet cable and power cable to corresponding interfaces.

B. Pass two cables through the waterproof silicone and slide into the grooves.

C. Screw the protective cover back to the device.

UG65 can also be powered by an 802.3af standard PoE injector or other PoE device. If both are

connected, DC power is preferred.

3.3 Antenna Installation

The antenna should be installed vertically always on a site with a good signal. After installation, please

select the corresponding installation type in web GUI.

Note: do not let the front panel of products faces to walls if using embedded LoRa antennas.

3.4 Hotspot Installation

UG65 can be mounted to a wall or a pole. Before you start, make sure that your SIM card has been

inserted, your antennas have been attached and all cables have been installed.

3.4.1 Wall Mounting

Preparation: mounting bracket, bracket fixing screws, wall plugs, wall mounting screws and other

required tools.

A. Align the mounting bracket horizontally to the desired position on the wall, use a marker pen to mark

four mounting holes on the wall, and then remove the mounting bracket from the wall.

Note: The connecting lines of adjacent points are at right angles.

B. Drill four holes with a depth of 32 mm by using your drill with a 6 mm drill bit on the positions you

marked previously on the wall.

C. Insert four wall plugs into the holes respectively.

D. Mount the mounting bracket horizontally to the wall by fixing the wall mounting screws into the wall

plugs.

E. Screw the bracket fixing screws to the back panel of the device, then hang the device to the

mounting bracket on the wall.

3.4.2 Pole Mounting

Preparation: mounting bracket, bracket fixing screws, hose clamp and other required tools.

A. Loosen the hose clamp by turning the locking mechanism counter-clockwise.

B. Straighten out the hose clamp and slide it through the rectangular rings in the mounting bracket,

wrap the hose clamp around the pole.

C. Use a screwdriver to tighten the locking mechanism by turning it clockwise.

D. Screw the bracket fixing screws to the back panel of the device, then hang the device to the

mounting bracket on the pole.

4. Login the Web GUI

UG65 provides a web-based configuration interface for management. If this is the first time you

configure the hotspot, please use the default settings below:

ETH IP Address: 192.168.23.150

Wi-Fi IP Address: 192.168.1.1

Wi-Fi SSID: Gateway_******

Username: admin

Password: password

4.1 Wireless Access

A. Enable wireless network connection on your computer and search for access point “Gateway_******”

to connect it.

B. Open a web browser on your PC (Chrome is recommended) and type in the IP address 192.168.1.1 to

access the web GUI, enter the username and password, click “Login”.

If you enter the username or password incorrectly more than 5 times, the login page will be

locked for 10 minutes.

C. After logging, select the correct antenna type according to your antenna installation and change the

default password following the guide.

After the guide completed, you can view system information and perform more advanced settings.

Disable WLAN feature or add password after you completed all hotspot settings!

Altri manuali per UG65

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Milesight Router wireless

Milesight

Milesight UR75 Manuale utente

Milesight

Milesight UF51 Manuale utente

Milesight

Milesight UF51 Manuale utente

Milesight

Milesight UR32 Manuale utente

Milesight

Milesight Pro Series Manuale utente

Milesight

Milesight UR35 Manuale utente

Milesight

Milesight LoRaWAN UG6 Series Manuale utente

Milesight

Milesight UG67 Manuale utente

Milesight

Milesight Ultra Series Manuale utente

Manuali Router wireless popolari di altre marche

Airlogic

Airlogic AirSync Class 1 Manuale del proprietario

Samsung

Samsung WCH730B Manuale utente

TELEFONICA

TELEFONICA USB Adapter Manuale utente

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuale utente

Askey

Askey RAC2V1K Manuale utente

Alloy

Alloy WLF2454AP-S Manuale utente

TP-Link

TP-Link TL-WR542G Manuale utente

NETGEAR

NETGEAR WNR2000v4 Manuale utente

Hama

Hama 53120 Manuale utente

Intellinet

Intellinet 524582 Manuale utente

Asus

Asus RT-N10P Manuale utente

D-Link

D-Link DIR-506L Manuale utente

Sapido

Sapido GR297n Manuale utente

Asus

Asus DSL-N55U Manuale utente

AMTC

AMTC WR7502 Manuale utente

Compaq

Compaq CP-2W - iPAQ Connection Point Manuale utente

SMC Networks

SMC Networks WBR14-N2 FICHE Manuale utente

Draytek

Draytek Vigor2120 Series Manuale utente