Milestone Da-Lite IDEA Screen Manuale utente

INSTRUCTION BOOK FOR

IDEA™ Screen

with Touch Interactive Bracket

for Epson BrightLink

12008

A BRAND OF MILESTONE AV TECHNOLOGIES | www.milestone.com

USA P 866.977.3901 E[email protected]

CANADA P 877.345.4329 Ecanadainfo@milestone.com

In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone AV Technologies ULC.

Da-Lite is a registered trademarks of Milestone AV Technologies. All other brand names or marks are used for

identiication purposes and are trademarks of their respective owners. All patents are protected under existing

designations. Other patents pending.

Tools Required For Assembly

Phillips Screwdriver Level

Rubber Mallet Measuring Tape

Hardware Provided

(9) #8 x ½” Screws

(1) Wall Bracket

(2) LBrackets

Disclaimer

Milestone and its ailiated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.

However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide

for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any

kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone

assumes no responsibility for accuracy, completeness or suiciency of the information contained in this document.

Important Safety Instructions

1. Read and understand all instructions before using.

2. Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the structure to which this component is attached can support the weight of all equipment. Reinforce

the structure as required before installing the component.

3. Use this projection screen only for its intended use as described in these instructions. Do not use attachments not recommended by the

manufacturer.

Save These Instructions

(2) M4 x 30mm

Screws

(2) M4 Nuts

7mm Wrench

Preparation

Note: It requires two people to assemble an IDEA Screen. To maintain optimal projected image geometry and screen alignment, a lat

and straight wall free from obstructions and angular distortions should be used.

Choose a clean work area for assembly using padded material or other soft, clean materials. The work area should be larger than the

overall screen size and directly in front of the location where the screen is to be installed.

Cleaning

Everyday Cleaning: The supplied foam eraser can be used to clean marks on the screen surface made by everyday dry erase marker

usage. Do not use spray cleaner in combination with the foam eraser.

Thorough Cleaning: For periodic full screen cleaning or to clean persistent marks from dry erase markers, use the supplied Da-Lite

spray cleaner and cleaning cloth. Use clean or dry sections of the microiber cloth when erasing the screen. This is important to prevent

smearing on the screen while cleaning. To clean permanent markers and other unintentional marks on the surface, use the supplied

foam eraser or the Da-Lite spray cleaner and cleaning cloth.

Assembly Instructions

1. Carefully unpack unit and place assembly on top of the clean

work area. The viewing surface must face up.

2. Center marker tray to the bottom of frame and attach with (3) of

the provided #8 x ½” screws. Insert screws through the tray into

the groove (Figure 1).

#8 X ½" Screws

Figure 1

3. Position the touch module bracket along the top of the IDEA

Screen by locating the two notches along the back side of

the frame. Using (2) provided #8 x ½” screws, attach the

bracket to the IDEA frame with the touch module facing

towards the audience. The front of the touch module bracket

should be lush with the screen surface (Figure 1)

NOTE: The Da-Lite touch module bracket will be used in

place of the mounting bracket provided with the projector’s

touch module.

NOTE: Do not rest the IDEA Screen on the marker tray while

attaching the touch module bracket to avoid damaging the

tray.

#8 X ½" Screws

Marker Tray

Touch Module Bracket

(See Detail A)

Detail A

Rear View

Front

Notches

Wall Mounting Instructions

NOTE: Use appropriate mounting hardware for the wall type and

to accommodate for the screen’s hanging weight (Figure 2).

Hardware is not provided.

1. Secure the wall bracket to wall studs at the desired height. Center

the wall bracket with the screen frame. You will need at least 1”

clearance above the drilled holes to hang the screen (Figure 2).

2. To install the (2) L-brackets, you must measure the overall height

of the screen frame and subtract 1⅛” (29 mm). Using that

dimension, measure down from the top edge of the wall brackets

and mark the wall for two screw holes. The outside edge of each

L-bracket must be no greater than 5” (127 mm) away from the left

and right edges of the screen frame (Figure 2).

3. Secure the two L-brackets to the wall at the marked locations. The

longest side of the two L-brackets should be pointing upwards

when secured in order to hide the L-brackets behind the screen

frame once the screen is installed.

NOTE: The L-brackets are necessary to maintain a lat

surface for touch interactivity.

4. This step requires two people. Hang the screen on the wall

brackets. There is a lip on the back of the frame that wedges itself

into the wall brackets once fully installed. Ensure that the screen

clears the L-brackets and that the screen weight is on the wall

brackets, not the L-brackets.

Wall Bracket

LBracket

No More

than 5”

(127 mm)

Figure 2

Screws (Not Supplied)

Determining Screen Placement: When installing the IDEA Screen with BrightLink projectors, you must leave at least 22” (56 cm) of

space between the top of the screen and the ceiling to accommodate the projector wall mount.

Wall Mounting Instructions (continued)

5. Tap the bottom of the two L-brackets with the rubber mallet until

they make contact with the frame. Secure the two L-brackets to

the frame with the remaining (4) #8 x ½” screws (Figure 3).

6. Attach bottom of screen to wall through the mounting holes

located under the marker tray.

#8 X ½" Screws

Figure 3

Attaching Touch Module

1. Remove the cover from the touch module provided with the

interactive projector. Using the provided M4 x 30mm screws

and M4 nuts, attach the touch module to the touch

interactive bracket as shown (Figure 4).

NOTE: The touch module can attach to the bracket with

hardware or magnets. Hardware attachment is

recommended.

2. Follow interactive projector’s instructions for aligning and

calibrating the IR curtain.

Figure 4

M4 x 30mm

Screws

M4 Nuts

Touch Module

LIMITED FIVE YEAR WARRANTY ON DA-LITE IDEA™PRODUCTS ONLY

Milestone AV Technologies LLC warrants these Da-Lite branded products to the original purchaser only, to be free from defects in materials and

workmanship for a period of ive (5) years from the date of purchase by the original purchaser; provided they are properly operated according

to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage,

or which has been tampered with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. Returns

for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses

to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use, or

merchantability, that may be mandated by statute or rule of law are limited to the ive (5) year warranty period. This warranty gives you speciic

legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE

LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT,

OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at 3100

North Detroit Street, Warsaw, IN 46582, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

Indice

Altri manuali Milestone Schermo di proiezione

Milestone

Milestone Da-Lite Slimline Electrol Manuale utente

Manuali Schermo di proiezione popolari di altre marche

FART PRODUKT

FART PRODUKT Standard SCREEN Manuale utente

Draper

Draper E Series Manuale

Elite Screens

Elite Screens Elite Tripod Series Manuale utente

Laarhoven

Laarhoven Companion II Manuale utente

Renogy

Renogy RMS-LFPS-US Manuale utente

Da-Lite

Da-Lite ExecutiveElectrol Manuale utente

Samsung

Samsung S*H65* Manuale utente

FONESTAR

FONESTAR PPTR-43100-FA Manuale utente

Slide Clear

Slide Clear Varro XL Manuale utente

Elite Screens

Elite Screens M85XWS1-SRM Manuale utente

OS РХ-090Н Manuale utente

Niko

Niko 10-845 Manuale utente

Speaka Professional

Speaka Professional 2357532 Manuale operativo

Sima

Sima XL-72 Manuale utente

Jasic

Jasic EVO 2.0 ET-200P Manuale utente

Elite Screens

Elite Screens Starling 2 Series Manuale utente

InFocus

InFocus SC-WALL GRY-92H Manuale

Barco

Barco OverView MVL-615 Manuale utente