Miller EnPak A30 Manuale utente

Page 1

EnPak®

A30 Quick Guide

Page 2

Knowing your EnPak

►EnPak A30 Diesel Side View

1. Maintenance label

2. Engine Oil Fill Cap

3. Engine Oil Dip Stick

4. Engine Oil Filter

5. Engine Air Filter

6. Engine Fuel Filter

7. Air Compressor Oil Drain

8. Air Compressor Oil Fill Cap

9. Air Compressor Oil Filter

Page 3

Knowing your EnPak

►EnPak A30 Gas Side View

1. Maintenance label

2. Engine Fuel Filter

3. Engine Oil Filter

4. Air Compressor Oil Drain

5. Air Compressor Oil Fill Cap

6. Air Compressor Oil Filter

Page 4

Knowing your EnPak

►EnPak A30 Gas Top View

1. Engine Oil Dip Stick

2. Engine Air Filter

3. Air Compressor Air Filter

4. Air Compressor Coalescing Filter

5. Fuse Box Assembly

Page 5

Knowing your EnPak – Remote Panels

►Main Control Remote Panel

1. Engine Control Switch

2. Engine/Compressor Service Indicator Lights

3. Process Switch

4. Adjust control/Select Button

5. DC Voltmeter

6. DC Ammeter

7. Arc Control Meter

8. USB Receptacle

9. Setup Light

10. Glow Light

11. Charge/Weld Switch

12. Compressor Switch

Page 6

Knowing your EnPak – Remote Panels

►Weld/Battery Charge Remote Panel

1. Battery Charge Receptacle

2. Positive Weld Receptacle

3. Negative Weld Receptacle

►Auxiliary Power Remote Panel (Optional)

1. 120/240 VAC 50A Receptacle

2. 120 VAC GFCI Receptacle

Page 7

Getting Started

Before Starting Your EnPak

Make sure the emergency brake is on and there is power to the EnPak remote panel. This could be a

master switch or EnPak switch. Make sure to check all uids and belts before starting.

First Start of the Day

Turn the Engine Control Switch to the Start position and release. The EnPak warning will beep and

automatic starting sequence begins. Allow the EnPak engine to warm up before work begins.

Engine Stop

Turn Engine Control Switch to OFF position.

Auto Start/Stop Function

To enable the auto start/stop feature place the Engine Control Switch in the Auto Start/Stop position.

To disable the auto/start top feature, place the Engine Control Switch in the Auto-Speed position.

Turn the Compressor On or Off

To turn the compressor on or off, position the compressor switch in the I (on) or O (off) position.

Battery Charge Mode

To enable the battery charge/crank assist feature, place the Charge/Weld switch in the charge

position and place the process switch in the position matching voltage of the battery being charged.

Chassis Power Mode

To enable the Chassis Power feature, place the Charge/Weld switch in the charge position and place

the process switch in the Chassis Power 12 V position. When using the EnPak to keep the truck

battery charged for multiple lights or other items, use the Chassis Power mode for high amperage

applications.

Weld Mode

To enable a weld mode, place the Charge/Weld switch in the weld position and place the process

switch in the position matching the desired weld process.

Page 8

Getting Started (continued)

Process Switch

The process switch works in conjunction with Charge/Weld Switch. Use switch to select weld process

and battery charge process – see table below.

Setting a GFCI from the EnPak Generator

The GFCI must see 120 V before setting. Start the EnPak, access the service menu as described

above, select “RPM SET”. Press and release the control to access the speed menu, select “3600”,

then press and release again to save selection. This will increase engine speed to 3600 rpm’s.

Now set the GFCI. Access the service menu and select “RPM SET” again, press and release the

control to access the speed menu and select “AUTO”, then press and release again to save selection.

The engine should go back to idle speed.

Process Switch Setting Typical Process Applications (DC Only)

OUTPUT ON

Output On – GMAW/FCAW (MIG)

MIG solid wire and dual shield ux core use a voltage sensing (VS)

feeder that does not require a control cable back to the welder/gen-

erator.

Output On – FCAW-S (Electrode Negative)

No Gas

FCAW (Flux Cored Arc Welding – self shielded) uses a voltage sensing

(VS) feeder that does not require a control cable back to the welder/

generator.

Output On – SMAW (STICK XX18 and

STICK XX10) Stick welding. Strike an arc to start welding

Output On – GTAW (Lift-Arc TIG) Lift-Arc TIG: touch tungsten to work and lift to start welding. Uses

circuitry internal to the welder/generator to aid arc start.

Output On – Aluminum Aluminum solid wire uses a remote connected spoolgun accessory.

BATTERY

CHARGE

Battery Charge 12 V Battery charging or jump starting with a 12 volt system.

Battery Charge 24 V Battery charging or jump starting with a 24 volt system.

Chassis Power 12 V Powering large 12 volt loads on vehicle such as electric cranes, lights,

or vehicle systems.

Service Menu

To access the service menu, press and hold the Adjust Control/Select Button for 5 seconds, then

release. Rotate the knob to scroll through the menu items. Press and release the control to access

the options and information within each menu item.

Rotate the control to scroll or change value. Press and release control to save selection. After 5

seconds of inactivity, the menu will time out and the selection will be saved.

Codes Shown on EnPak Remote Control Panel Display

You could see a code show up on the EnPak screen to let you know there is some type of issue.

Check the manual for error code reference to help repair the issue. Resetting of Charge/Weld codes

can be done by either: changing position of the charge/weld switch; change positions of the process

select switch; cycle unit power off/on. Resetting of Air Compressor codes can be done by switching

the compressor Off, then On.

Getting Started (continued)

Menu Item

Selectable Item

Option(s) Description

HOUR MTR – – Displays the current Engine Hours.

ENG OIL

OIL HOUR Displays the current oil change countdown.

OIL SET Sets the oil change interval.

OIL RSET Resets the oil change countdown.

COMP OIL

OIL HOUR Displays the current oil change countdown.

OIL SET Sets the oil change interval.

OIL RSET Resets the oil change countdown.

RPM DISP – – Displays current engine RPM.

RPM SET

AUTO Enables auto speed function.

3600 Locks engine speed at 3600 RPM.

STOP TIME 2 to 30 min Unit idle time before auto stop (adjustable in 1 min increments).

MIN PRES 90 psi up to 10 psi less

than max pressure

Minimum pressure to start air compressor (adjustable in 1 psi

increments).

MAX PRES 175 psi down to 10 psi

greater than min pressure

Maximum pressure to stop air compressor (adjustable in 1 psi

increments).

SOFT WARE – – Displays the current revision of rmware installed.

FACT RSET

RSET YES Resets all settings to factory defaults.

RSET NO All settings remain at previous settings.

Page 10

Notes

UpFitter Information

UpFitter: ____________________________________ Location: ____________________________________

Phone: ______________________________________ Email: _______________________________________

_____________________________________________________________________________________________

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Miller Sistema di saldatura

Miller

Miller ICE-27T Manuale utente

Miller

Miller WDW100 Manuale utente

Miller

Miller PowCon Arc Stud 625 Manuale utente

Miller

Miller ST 44 Series Manuale utente

Miller

Miller INTELLIMATIC S-52M Manuale utente

Miller

Miller MigMatic 300 Manuale utente

Miller

Miller Big Blue 500X CE Manuale utente

Miller

Miller TRAILBLAZER 302 AIR PAK Manuale utente

Miller

Miller Bobcat 260 Manuale utente

Miller

Miller Augmented Arc Manuale utente

Miller

Miller SUBARC WIRE DRIVE 400 T CE Manuale utente

Miller

Miller SDX-575 Manuale utente

Miller

Miller AUTO ARC TIG 50A Manuale utente

Miller

Miller 14-Pin Insight Core CE Manuale utente

Miller

Miller SRH-222 Manuale utente

Miller

Miller Millermatic 210 Manuale utente

Miller

Miller INVISION 350 MPa AUTO-LINE Manuale utente

Miller

Miller Millermatic 252 Manuale utente

Miller

Miller Summit Arc 1000 Manuale utente

Miller

Miller Auto Invision II Manuale utente

Miller

Miller Auto-Continuum 350 Manuale utente

Miller

Miller Spoolmatic 30A Manuale utente

Miller

Miller DYNASTY 200 DX Manuale utente

Miller

Miller MigMatic 220 Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

ESAB

ESAB Buddy Arc 145 Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuale utente