Minikol M15S Manuale utente
Index
1. Operation overview and general introduction......................................................... 1
2. Operation Modes ................................................................................................... 2
2.1. Manual mode ..................................................................................................2
2.2. Single mode....................................................................................................3
2.2.1. Setting target value...............................................................................3
2.2.2. Start / Stop / Cancel ..............................................................................3
3. Fast Program (10 sets) .......................................................................................... 5
3.1. Entering preset target values ..........................................................................5
3.2. Execute...........................................................................................................6
4. Select counting direction (+/-) ................................................................................ 7
5. Select Positioning Mode ........................................................................................ 7
6. Select Speed Mode................................................................................................ 8
7. Set Retract Distance .............................................................................................. 9
8. Set Conveyer Diameter.......................................................................................... 9
9. Set Pulse/Rev Input from Conveyer..................................................................... 10
10. Set software Limit (Hi/Lo End) ........................................................................... 10
11. Set Tolerance ......................................................................................................11
12. Set Low Speed Limit .......................................................................................... 12
13. Set Linear Correction ......................................................................................... 13
14. Enter Parameter Setting Mode........................................................................... 14
15. Check Software Version..................................................................................... 15
16. Load datum values............................................................................................. 16
16.1. Presetting the real value .............................................................................16
16.2. Load the real value .....................................................................................16
16.3 Example:......................................................................................................17
17. Presetting tool radius – 10 sets.......................................................................... 18
17.1. Setting the tool radius .................................................................................18
17.2. Loading a new tool......................................................................................18
17.3. Example for Tool setting:.............................................................................19
17.4. Example to execute ....................................................................................20
18. Fine adjustment ................................................................................................. 21
19. Check belt speed ............................................................................................... 22
20. IN/MM Conversion ............................................................................................. 22
21. Installation Guide ............................................................................................... 23
21.1. The Magnetic Tape .....................................................................................23
21.2. Installation...................................................................................................24
22. Set Device Resolution........................................................................................ 25
23. Change Counting Direction................................................................................ 25
24. Calibration.......................................................................................................... 26
25. Power supply & Hardware ................................................................................. 27
26. Troubleshooting ................................................................................................. 28
27.External Dimension............................................................................................. 30
28. Appendix A -- M15 Specifications ....................................................................... 31
29. Appendix B -- Parameter.................................................................................... 32
MBE059F03 1 / 32
1. Operation overview and general introduction
1.1 Front panel
minikol M15
QTY RPM DEG
7
4
1
+/-
8 9
6
3
5
2
0
PROG
STOP
START
F
MM
INCH
S
Target value window
Manual
Single
Real value window
MBE059F03 2 / 32
2. Operation Modes
There are two base operating modes – MANUAL and SINGLE.
In MANUAL mode: The operator can move the machine using the M15
keyboard.
In SINGLE mode: Automatic positioning is performed.
Press
to select Manual mode or Single mode
。
※
When LED lamp on – Manual mode
；
LED lamp off – Single mode.
MANUAL
SINGLE
MANUAL
SINGLE
MANUAL
SINGLE
2.1. Manual mode
Keyboard Function：
8 97 F
FAST Backward Forward FAST
If two-speed positioning mode has been selected, the fast forward and fast
backward keys are functional and start fast movement of the machine
table.
If one-speed positioning mode has been selected, the fast forward and fast
backward keys have the same function as forward and backward keys.
When forward key is pressed, the machine table starts to move in the
direction to increase the distance – away from the cutting edge of the tool
(machine table goes down).
When backward key is pressed, the machine table starts to move in the
direction to decrease the distance – close to the cutting edge of the tool
(machine table goes up).
The machine moves until a key is hold pressed. When the key is released,
the machine stops.
This mode can be used for manual positioning, or adjusting procedures.
MBE059F03 3 / 32
2.2. Single mode
In single mode, the device performs automatic positioning of the machine
to the programmed target position.
2.2.1. Setting target value
Step 1 : Press
PROG
(Target window LED starts blinking)
Step 2 : Enter the target value using numerical keypad;
Step 3 : Press to complete .
※LED lamp starts blinking – the device is ready
to start the positioning .
2.2.2. Start / Stop / Cancel
Press to start the positioning. The LED lamps now stops
blinking and remains on during the procedure.
Press to cancel the positioning. The LED lamp is turned off.
START
START
STOP
If the key is pressed when the positioning is already running,
the procedure is interrupted, the machine is stopped,
and the LED is turned off. To repeat the positioning of the
START
STOP
same target, press .
To program another target value press
–enter new value –
PROG START
START
PROG
MBE059F03 4 / 32
2.3. Example：
Assume:
actual target value on display = 100.00mm;
actual real value on display = 100.00mm
To change the target value to 20.25mm
Step 1 : Press Æthe LED lamp on Target window is blinking.
PROG
１００００
１００００
Display Target value
Current value
Step 2 : Enter new target value Exp：20.25mm
02 52
Press
２０２５
１００００
Target value
Display
Current value
Step 3 : Press to complete .
※The LED lamp is blinking – ready for positioning.
START
Press to start the positioning or press to cancel.
START STOP
MBE059F03 5 / 32
3. Fast Program (10 sets)
To facilitate frequently used positions, the keys 0 to 9 have associated
preset target values. By pressing one of these keys, its target value is
loaded automatically, and the positioning can be started immediately.
3.1. Entering preset target values
Step 1: Press
Step 2: Select a key 0-9 (total of 10 values).
Step 3: Enter the target value.
Step 4: Press to confirm
※Follow the same procedure for other program setting;
Press to exit.
3.1.1. Example：Program 0 = 10.00mm；Program 1 = 20.00mm .
Step 1: Press
F5 5
55F
ＰｒｏＧ _
Display
Step 2: Press .….……………………..【select preset value 0】
0
Step 3: Press .……..…………………..【enter value】
01
Step 4: Press ……………..………………………...【complete】
Step 5: Press ..……………………….【select preset value 1】
1
MBE059F03 6 / 32
Step 6: Press ..…….…………………….【enter value】
02
Step 7: Press …………………….………………..【complete】
Step 8: Press to exit
3.2. Execute
Step1: Enter single mode, LED lamp is off.
Step2: Press a key 0-9
※ LED lamp is blinking -> ready for start .
3.3. Example:Program# 0 = 10.00mm, Program# 1: 20.00mm
Step 1: In Single mode, LED lamp is off.
Step 2: Press …………………………………….【program# 0 】
MANUAL
SINGLE
0
MANUAL
SINGLE
START
Now you will see the preset value: 10.00mm (program# 0)
LED lamp is blinking, complete.
START
Press to begin positioning.
START
MBE059F03 7 / 32
4. Select counting direction (+/-)
You can select the counting direction according to the machine movement.
Step 1: Press
Display ………………【default】
F1
－ ｄｉｒ
Setp 2: Press to change the direction, "-dir" for left or "dir- "
PROG
for right.
Step 3: Press to confirm or press to clear.
5. Select Positioning Mode
Step 1: Press
Step 2: Press to select:
F4
PROG
a. ---||--- both directions
b. ---| left
c. |--- right
Step 3: Press to confirm or press to clear.
Indice
