Minuteman MC20004CE Guida
200X
Brush Drive
Floor Scrubber
Electric
Model: MC20003QP
MC20004CE
Revised 6/02
OPERATION SERVICE PARTS CARE
TABLE OF CONTENTS
Page
Safety Instructions 1
Electrical Requirements 2
Control Panel Identification 3
Operating Instructions 4
Squeegee Adjustments 5
Brush Installation/Removal 6
Base Assembly 7 & 8
Tank Assembly 9 & 10
Upper Assembly 11
Console Assembly 12
Motor Lift Assembly 13
Scrubhead Assembly 14
Back Panel Assembly 15
Squeegee Lift & Mechanism Assembly 16
Squeegee Assembly Complete 17
Wiring Diagram, 115V 18
Wiring Diagram, 230V CE 19
1
FOR COMMERCIAL USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the
following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING - To reduce the risk of fire, electric shock, or injury:
• Do not leave appliance when plugged in. Unplug from outlet when not
in use and before servicing, cleaning or maintaining.
WARNING
To reduce the risk of electric shock - Do not expose to rain. Store indoors.
• Do not allow to be used as a toy. Close attention is necessary when used
by or near children.
• This machine shall be used only by instructed and authorized persons.
• Use only as described in this manual. Use only manufacturer’s recommended
attachments.
• Inspect cord regularly. Do not use with damaged cord or plug. If appliance
is not working as it should, has been dropped, damaged, left outdoors, or
dropped into water, return it to a service center. Use only cord specified
by manufacturer.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or
pull cord around sharp edges or corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked;
keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings
and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.
• Do not use without dustbag and/or filters in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or
use in areas where they may be present.
• Connect to a properly grounded outlet only. See grounding instructions.
• This machine is not suitable for picking up hazardous dust.
• Close tank and lid before use.
SAVE THESE INSTRUCTIONS
2
INSPECTION
Carefully unpack and inspect your machine for shipping damage. Each unit is tested and
thoroughly inspected before shipment, and any damage is the responsibility of the delivery
carrier who should be notified immediately.
WARNING
• Read Instruction Manual before operating this piece of equipment.
• To reduce the risk of fire use only commercially available floor cleaners and
waxes intended for machine application.
• To reduce the risk of electrical shock, do not expose to rain. Store indoors.
• Do not cross over supply cord, hazard exists when rotating brush passesover cord.
• Electrical motors and components can cause an explosion when operated near volatile
materials and vapors. Do not use this machine near flammable materials such as
solvents, thinners, fuels, grain dust, etc.
ELECTRICAL
(Model MC20003QP) This floor machine is designed to operate on a standard 15 amp.
120 volt, 60 hz, AC circuit. Voltages below 105 volt AC or above 125 volts AC could cause
serious damage to the motor.
(Model MC20004CE) This machine is designed to operate on a standard 16 amp. type L
fused 230 volt, 50 hz, AC circuit. Voltages below 200 volt AC or above 250 volts AC could
cause serious damage to the motor I.E. C. Class 1.
GROUNDING INSTRUCTIONS
• This floor finishing machine should be grounded while in use to protect the operator from
electric shock. The machine is equipped with a three-prong grounding type attachment
plug to fit the proper grounding type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Never connect this wire to other than the
grounding blade.
• If the machine is provided with an attachment plug as shown in Sketch A it is intended
for use on a 120-volt (nominal) circuit. If a properly grounded receptacle as shown in
Sketch A it is intended for use on a 120-volt (nominal) circuit. If a properly grounded
receptacle as shown in Sketch A is not available, an adapter as shown inSketch C is
available and should be installed as shown in Sketch B if the outlet box that houses the
receptacle is grounded. Be sure to fasten the grounding tab with the faceplate screw.
ADAPTER (Not applicable in Canada)
METAL SCREW
GROUNDING
COVER OF GROUNDED MEANS
OUTLET BOX
GROUNDING PIN (C)
(A) (B)
3
1. Squeegee lift lever
2. Recovery dump hose
3. Dashboard control panel
4. Solution control lever
5. Solution dump hose
6. Quick disconnect
Aux. out (optional)
7. Food pedal
8. Receptacle
9. Circuit breaker
10. Main power
11. Brush switch
12. Vacuum switch
13. Pump switch (optional)
COMPARISON RECOMMENDED
TYPE DESCRIPTION DURABILITY* COLOR TO PADS USE
Bassine Natural Fiber Short Dark Brown Red Light duty
general cleaning,
acid etching
Nylon Nylon Medium Black Tan/Red General cleaning
& scrubbing vinyl
floors, ceramic tile
& concrete floors
Dyna-Scrub Nylon impregnated Long Light Blue Red General scrubbing,
with 500 Grit vinyl tile, ceramic
Silicon Carbide tile, epoxy floors,
Fine Bristle, urethane finish,
Dense Fill uneven concrete floors
Power-Scrub Nylon impregnated Long Rust Red/Blue Moderate aggressive
with 120 Grit Silicon scrubbing, tile floors,
Carbide Fine Bristle, concrete floors
Dense Fill
Poly-Grit Nylon impregnated Long Green Brown/Black Aggressive stripping
with 80 Grit and scrubbing, tile
Silicon Carbide floors, unfinished
Coarse Bristle concrete floors
Strata-Grit Nylon impregnated Long Dark Blue Black Heavy duty
with 46 Grit stripping/scrubbing
Silicon Carbide unfinished concrete
Coarse Bristle
AUTO SCRUBBER BRUSH DESCRIPTION
••
••
•
Durability is dependent on floor surface, chemicals used and proper care.
4
OPERATING INSTRUCTIONS
BEFORE STATING, FAMILIARIZE YOURSELF WITHTHE MACHINE AND ITS CONTROLS
(SEE “MACHINE OVERVIEW” & CONTROL PANEL DIAGRAMS)
1. Filling: Fill the solution tank with the desired amount of water and add liquid
cleaning solution to the proper dilution ratio. DO NOT USE powdered cleaning
chemicals. Powders are unlikely to dissolve thoroughly, resulting in clogging the
in-line solution filter. This can reduce or stop water flow to the brush.
2. Close lid.
3. Turn on machine by pressing the main power switch (10).
4. Lower brush assembly.
- To lower the brush, first push the pedal (7) slightly outward on the machine (unlock it),
and then release it slowly.
- To lift the brush, press the pedal (7) down until lift mechanism engages.
5. Turn on brush (11).
6. Adjust solution control feed lever (4).
7. Turn on vacuum switch (12).
8. Lower squeegee assembly by lowering handle (1).
After Use:
1. Turn off solution feed (4).
2. Switch off brush (11) and raise (7).
3. Raise squeegee assembly (1).
4. Turn off vacuum motor (12).
Solution and recovery tanks should be emptied after every use.
MAINTENANCE:
Daily 1. Clean float assembly & squeegee blades. Vac filter.
Monthly 1. Check wear on squeegee blades.
2. Grease front wheels.
3. Grease pivot points on brush motor assembly.
Every 500 hours check condition of carbon brushes on vacuum motor and brush drive motor.
5
SQUEEGEE ADJUSTMENTS
Squeegee Adjustment
The squeegee set-up is pre-adjusted
at the factory. Adjustments may be required
to get optimum performance for different
floors and conditions.
Pitch Control Adjustment
1. Ensure that the scrubber is on
a relatively flat surface. Pull the
red emergency button away from
the dashboard to activate power.
Turn on the main power switch
and turn the key switch. Raise
the scrubhead off the floor.
Turn the vacuum switch.
2. Lower the squeegee (item 1)
to the floor and move the
machine one or two feet
forward to check the rear
squeegee blade for uniform
deflection to the floor.
3. If uneven deflection or lay is evident, minor adjustments may be necessary to avoid
streaking and uneven wear on the blade.
4. To correct this, pitch adjustment is necessary. Loosen the pivot screw (item 2) and the pitch
screw (item 3). Move the machine forward and allow the squeegee to level itself or adjust
the angular position accordingly to achieve a uniform blade deflection. Re-tighten screws.
5. In certain applications where a different blade set-up is required, the reinforcement blade
(item 4) may be turned upside down. The notch, which is normally on the bottom will now
be located on the topside. This allows the rear squeegee blade a larger deflection than
normal.
6
BRUSH INSTALLATION - REMOVAL
INSTALLATION
1. Raise the scrubhead to the “UP” position by depressing the pedal (A) downward as
shown on Fig. 1.
2. Center brush (D) under the scrubhead shroud while lining up the center
hex drive hub and pressing the brush up until the brush engages on the drive hub.
REMOVAL
1. Raise the scrubhead to the “UP” position by depressing the pedal (A) downward as
shown on Fig. 1.
2. Remove the brush (D) by stepping on the “BRUSH RELEASE PIN”
on the top of the scrubhead shroud as shown on Fig. 1 below.
Figure 1
7
BASE ASSEMBLY
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Minuteman Macchina per pavimenti
Minuteman
Minuteman X17 ECO CFS Manuale utente
Minuteman
Minuteman PowerBoss 26 Series Guida
Minuteman
Minuteman FR17115-11 Guida
Minuteman
Minuteman Powerboss PB32036CE Guida
Minuteman
Minuteman Lumina 20 Traction Drive Manuale elenco delle parti
Minuteman
Minuteman X17 Manuale utente
Minuteman
Minuteman M26036QP Manuale elenco delle parti
Minuteman
Minuteman FR20115-DC Manuale utente
Minuteman
Minuteman MC17000-00CE Guida
Minuteman
Minuteman Lumina 20 M26036QP Guida
Minuteman
Minuteman PowerBoss MC380000 Guida
Minuteman
Minuteman Kleen Sweep 27 Manuale elenco delle parti
Minuteman
Minuteman M17120-00 Manuale utente
Minuteman
Minuteman M220028K13H Manuale elenco delle parti
Minuteman
Minuteman Rush 100 Cold Manuale elenco delle parti
Minuteman
Minuteman MC20000QP Manuale operativo
Minuteman
Minuteman C-BOX 100 Manuale utente
Minuteman
Minuteman Mirage M220028K17X Manuale elenco delle parti
Minuteman
Minuteman E Ride 26 Manuale utente
Minuteman
Minuteman ROS 17 ORB 115V Manuale utente
