Minuteman Enterprise Series Manuale utente

1-866-207-6631 | sales@rackmountsolutions.net

www.rackmountsolutions.net

Enterprise Series

Owner's Manual

1. Introduction 2

2. Controls and Indicators 4

3. Installation 5

4. Operation 9

5. Troubleshooting 11

6. Replacing the Battery 12

7. Obtaining Service 14

8. Specifications 15

9. Configurable Parameters & Settings 16

10. Limited Product Warranty 18

11. Declaration of Conformity 19

English

TABLE OF CONTENTS

Thank you for purchasing a MINUTEMAN power protection product. It has been designed

and manufactured to provide many years of trouble free service.

Please read the manual before installing your Enterprise Series UPS. It

provides the information that should be followed during installation and

maintenance of the UPS and the batteries allowing you to correctly set up your

system for the maximum safety and performance.

Included is information on customer support and factory service if it is required. If you

experience a problem with the UPS please refer to the Troubleshooting guide in this

manual to correct the problem or collect enough information so that the MINUTEMAN

Technical Support Department can rapidly assist you.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS !

NOTICE: This equipment has been tested and found to comply with the limits

for a Class B computing device in accordance with the specifications in Subpart J

of Part 15 of FCC Rules and the Class B limits for radio noise emissions from digital

apparatus set out in the Radio Interference of the Canadian Department of

Communications. These limits are designed to provide reasonable protection against such

interference in a residential installation. This equipment generates and uses radio frequency

and if not installed and used properly, that is, in strict accordance with the manufacturer's

instructions, this equipment may cause interference to radio and television reception. If this

equipment does cause interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

nRe-orient the receiving antenna

nRelocate the computer with respect to the receiver

nMove the computer away from the receiver

nPlug the computer into a different outlet so that the computer and receiver are on

different branch circuits.

nShielded communications interface cables must be used with this product

After removing your MINUTEMAN UPS from it's carton, it should be inspected for damage

that may have occurred in shipping. Immediately notify the carrier and place of purchase if

any damage is found. Warranty claims for damage caused by the carrier will not be

honored.

ReceivingInspection

WARNING: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

English

INTRODUCTION



WARNING: RISK OF ELECTRICAL SHOCK. HAZARDOUS LIVE PARTS

INSIDETHISPOWERSUPPLY AREENERGIZEDFROMTHEBATTERYEVEN

WHENTHEACINPUTPOWERISDISCONNECTED.

TODE-ENERGIZETHEOUTPUTSOFTHEUPS:

1.IFTHEUPSISONPRESSTHEON/OFFBUTTONFOR1SECOND

2.DISCONNECTTHEUPSFROMTHEACPOWEROUTLET

3.TODEENERGIZETHEUPSCOMPLETELY, DISCONNECTTHEBATTERY.

(see section 6 for instructions)

CAUTION! TOREDUCETHERISKOFELECTRICALSHOCKINCONDI-

TIONSWHERELOADEQUIPMENTGROUNDINGCANNOTBEVERIFIED,DISCON-

NECTTHE UPSFROMTHEACPOWEROUTLETBEFOREINSTALLINGACOM-

PUTERINTERFACECABLE.RECONNECTTHEPOWERCORDONLYAFTERALL

SIGNALINGCONNECTIONSAREMADE.

CAUTION! CONNECTTHEUPS TOATWOPOLE,THREEWIREGROUND-

INGACPOWEROUTLET.THERECEPTACLEMUSTBECONNECTEDTOAPPROPRI-

ATEBRANCHPROTECTION(CIRCUITBREAKERORFUSE).CONNECTIONTOANY

OTHERTYPEOFRECEPTACLEMAYRESULTINASHOCKHAZARDANDVIOLATE

LOCALELECTRICALCODES

Para Systems Life Support Policy

As a general policy, Para Systems Inc. (Para Systems) does not recommend the use of any

of its products in life support applications where failure or malfunction of the Para Systems

product can be reasonably expected to cause failure of the life support device or to

significantly affect its safety or effectiveness. Para Systems does not recommend the use

of any of its products in direct patient care. Para Systems will not knowingly sell its

products for use in such applications unless it receives in writing assurances satisfactory

to Para Systems that (a) the risks of injury or damage have been minimized, (b) the

customer assumes all such risks, and (c) the liability of Para Systems Inc. is adequately

protected under the circumstances.

Examples of devices considered to be life support devices are neonatal oxygen analyzers,

nerve stimulators (whether used for anesthesia, pain relief, or other purposes), auto

transfusion devices, blood pumps, defibrillators, arrhythmia detectors and alarms, pacemak-

ers, hemodialysis systems, peritoneal dialysis systems, neonatal ventilator incubators,

ventilators for both adults and infants, anesthesia ventilators, and infusion pumps as well as

any other devices designated as “critical” by the United States FDA.

Hospital grade wiring devices and leakage current may be ordered as options on many

PARA SYSTEMS UPS systems. PARA SYSTEMS does not claim that units with this

modification are certified or listed as Hospital Grade by PARA SYSTEMS or any other

organization. Therefore, these units do not meet the requirements for use in direct patient

care.

The packing materials that your UPS was shipped in, are carefully designed to minimize any

shipping damage. In the unlikely case that the UPS needs to be returned to MINUTEMAN,

please use the original packing material. Since MINUTEMAN is not responsible for shipping

damage incurred when the system is returned, the original packing material is inexpensive

insurance.

PLEASE SAVE THE PACKING MATERIALS!

English

Press and release the ON/OFF/TEST button after one beep to turn the unit ON or

OFF (see section 4)

On-Line On-Battery Buck Boost

The On-Line/On-Battery/Boost and Buck (green) LED illuminates in a steady

state when the UPS is on and supplying AC power to the load. The LED blinks

and the audible alarm sounds, when supplying battery power to the load.

The Fault (red) LED illuminates when the UPS has detected an internal fault. (see

section 5)

The Overload (yellow) LED illuminates when the loads connected to the UPS

exceeds the UPS power rating. (see section 5)

The Weak/Bad Battery (red) LED illuminates when the UPS has detected that the

batteries are Weak/Bad. Battery replacement might be required. (see section 5)

The Site Wiring Fault (red) LED illuminates when the UPS detects a improperly

wired AC outlet. (see section 5)

FRONTPANEL

English

Ente rpri s e E 32 00

SWF

On-Line/On-Battery/Boost/BuckLED

FaultLED

OverloadLED

Weak/BadBatteryLED

SiteWiringFault LED

On/Off/Test Switch

CONTROLS AND INDICATORS

INSTALLATIONPLACEMENT

Install the UPS in a temperature controlled environment that is free of conductive contami-

nants. Select a location which will provide good air circulation for the UPS at all times. Avoid

locations near heating devices, water or excessive humidity, or where the UPS is exposed

to direct sunlight. Route power cords so they cannot be walked on or damaged.

REAR PANEL (120Vac models shown)

English

1. The computer interface port is for the UPS monitoring and control. (see section 3)

2. The RJ-45/RJ-11 modular connectors are used for 10 Base-T network/single line

telephone surge protection. (see section 3)

3. The output receptacles are NEMA 5-15R type. (IEC output sockets on 230Vac models)

4. The output circuit breakers will trip in the event the individual banks of the output recep-

tacles exceed the rating of the circuit breaker (Not on all models).

5. The external battery connector is for connecting an external Battery Pack.

6. The access panel is for option cards available from MINUTEMAN.

7. The input circuit breaker will trip in the event the load exceeds the UPS's power rating.

8. The input power cord has a NEMA 5-15P connector. (IEC input socket on 230Vac models)

9. The DIP Switch setting may be changed by the user to set the desired inverter (on

battery) output voltage. (see section 4)

10. The "Surge Only" output receptacle is for surge protection only it is not battery

backed-up.

INSTALLATION

English

The Desk Top Configuration allows the user to install the monitor, the computer and the

UPS in one single stack. There are four self-stick rubber feet provided with UPS. The four

rubber feet can be installed on the bottom side of the UPS. Use CAUTION, the UPS is

extremely heavy. Once the location of the UPS has been determined, stand the UPS on it's

side. Attach the self-stick rubber feet to the bottom of the UPS, approximately 2" from each

corner. Lay the UPS down on the four rubber feet. Stack the computer and then the monitor

on top of the UPS. NOTE: Do not stack the UPS on top of the computer. The UPS is heavy

and may damage the other equipment. Now the UPS is ready for the normal start-up

procedure.

INSTALLATION

Be sure to read the installation placement and all the cautions before installing the UPS. The

Enterprise series UPS has external Battery Pack capability, please observe the following

warning when connecting the Battery Pack(s). WARNING! DO NOT PLUG THE BATTERY

PACK'SPOWERCORDINTOTHEUPS'sOUTPUTRECEPTACLES,DAMAGETOTHEBATTERY

PACK'S INTERNAL CHARGER MAY OCCUR. NOTE: Thered connector isthebattery

positive(+) and the black connector is the battery negative(-) on all MINUTEMAN configura-

tions. The Enterprise series UPSs can be installed in four different configurations.

The Wall Mount Configuration allows the user to mount the UPS on the wall. There is a

wall mount bracket kit available for the UPS. The kit includes two mounting brackets, twelve

retaining screws, four bolts, one drill bit and the template for the bolt holes. Use CAUTION,

the UPS is extremely heavy. The UPS's side panels have mounting bracket screw holes for

attaching the wall mounting brackets. Once the location and position of the UPS has been

determined, lay the UPS down flat. Align the mounting bracket with the mounting bracket

screw holes and attach with the retaining screws. Use the template to mark the bolt hole

position on the wall. CAUTION, you should always were protective gear for your hands

and eyes when operating power tools. Drill the holes for the bolts and make sure that all of

the holes are drilled into structural material. Then clean the area of any loose material.

Install the four bolts into the bolt holes. Do not tighten the bolts all the way, leave approxi-

mately 3/8" of the bolt sticking out. Position the UPS, so that the mounting bracket keyed

holes line up with the four bolts. Slide the UPS down until its resting securely on the four

bolts. Tighten the four bolts to secure the UPS to the wall. The face plate can be rotated to

read in the up-right position. Pull the front panel off the UPS. On the backside of the front

panel, there are four tabs holding the face plate to the front panel. Push the four tabs

inward and the face plate will pop out. Position the face plate so that it reads in the up-right

position. Install the front panel on the UPS. Now the UPS is ready for the normal start-up

procedure.

English

The Tower Configuration allows the user to install the UPS in the up-right position next to

the tower computer. There is a tower bracket kit available for the UPS. Use CAUTION, the

UPS is extremely heavy. Once the location of the UPS has been determined, lay the UPS

down flat on a desk or a table. Position the UPS so that the tower brackets will slide on the

unit. Locate the mounting bracket screw holes on the side panel of the unit, there are four

mounting bracket screw holes at the front of the unit and four at the rear of the unit. Align

the brackets with the mounting bracket screw holes and attach with the retaining screws.

Stand the UPS up on the tower brackets. Slide the UPS and the tower computer together.

NOTE: Verify that the UPS is stable. The face plate can be rotated to read in the up-right

position. Pull the front panel off the UPS. On the backside of the front panel, there are four

tabs holding the face plate to the front panel. Push the four tabs inward and the face plate

will pop out. Position the face plate so that it reads in the up-right position. Reinstall the

front panel on the UPS. Now the UPS is ready for the normal start-up procedure.

EnglishEnglish

CONNECTING TOAN ACSOURCE

Plug the UPS into a two pole, three wire, grounded receptacle only. Do not use extension

cords or adapter plugs.

CONNECTINGTOTHETELEPHONE/NETWORKSURGE PROTECTION

CONNECTION IS OPTIONAL. THE UPS WORKS PROPERLY WITHOUT A

CONNECTION.

NOTE:

CONNECTING TO THE COMPUTER INTERFACE PORT IS OPTIONAL. THE UPS

WORKSPROPERLYWITHOUTACONNECTION.

COMPUTERINTERFACE CONNECTION(OPTIONAL)

MINUTEMAN Power Management software and interface cables kits can be used with the

Enterprise units. Use only MINUTEMAN or MINUTEMAN approved interface cables with these

UPS’s. Connect the interface cable to the 9 pin computer interface port on the rear of the

UPS. Secure the connector to the UPS via the screws on the connector housing. Connect

the other end of the cable to the device that will be monitoring/controlling the UPS.

TELEPHONE/NETWORK SURGE PROTECTIONCONNECTION (OPTIONAL)

Connect a single line telephone or a 10 Base-T network line to the protection sockets on the

rear of the UPS. This connection will require another length of telephone or network cable.

The cable coming from the telephone service or networked system is connected to the port

marked “IN”. The “OUT port is connected to the equipment to be protected.

The Rackmount Configuration comes with mounting brackets for the standard 19"

(46.5cm) rack. The mounting brackets to fit a 23" (59.2cm) standard rack are also

available. The screws for mounting the UPS to the rack are not included (screw size

varies with rack size). The kit includes, two mounting brackets and eight retaining

screws. Locate the mounting bracket screw holes on the side panels of the UPS, at the

front of the UPS. Align the mounting bracket with the mounting bracket screw holes.

Attach the mounting bracket with the retaining screws. WARNING: Use two or more

people when installing the UPS into the rack. Use caution, the UPS is extremely heavy. Do

not move the rack after the units have been installed. The rack maybe unstable due to the

weight distribution. Now the UPS is ready for the normal start-up procedure.

NOTE:

English

TURNING THE UNIT ON/OFF

Press and release the ON/OFF/TEST SWITCH. After one beep the unit will turn on and supply

power to the load. The load is immediately powered while the UPS runs a 5 second self test.

Press and release the switch to turn the unit off. The UPS will continue to charge the

batteries whenever it is plugged in and there is AC present.

ON / OFF / Test Switch

CHECKING THE SITE WIRING FAULT (120Vac models only)

After plugging in the UPS, check the Site Wiring Fault (SWF) LED on the front panel of the

unit. If the LED is illuminated the UPS is plugged into an improperly wired AC outlet.

CHARGING THEBATTERY

The Enterprise Series UPS will charge the internal batteries whenever the unit is connected

to an AC source and the circuit breaker on the back panel is in the "On" position. It is

recommended that the UPS's batteries be charged for a minimum of 4 hours before use. The

UPS may be used immediately, however, the “on battery” run time may be less than normally

expected.

CAUTION! IF THE UPS INDICATES A SITE WIRING FAULT, HAVE A

QUALIFIEDELECTRICIAN CORRECT THE PROBLEM.

CONNECTING YOUREQUIPMENT

CAUTION!

DO NOT CONNECT A LASER PRINTER TO THE BATTERY BACKUP

RECEPTACLES ON THE UPS UNLESS THE UPS IS RATED 2000VA OR

GREATER. A LASER PRINTER DRAWS SIGNIFICANTLY MORE POWER

WHEN PRINTING THAN AT IDLE, AND MAY OVERLOAD THE UPS.

Plug the equipment into the output receptacles on the back panel of the unit. Insure that you

do not exceed the maximum output rating of the UPS (refer to the UPS's back panel or the

Electrical Specifications in this manual).

SELF TEST ON / OFF / Test Switch

The self test feature is useful to verify the correct operation of the UPS and the condition of

the batteries. With the UPS plugged into normal AC press and hold the ON/OFF/TEST SWITCH

for 4 seconds (two beeps) then release the switch. The UPS will perform a five second self

test. Note: The UPS will automatically perform a self test on startup and every

two weeks. During the self test the UPS will switch to battery power and the On-Line LED

will blink and the audible alarm will sound as well. The length of the test that is automatically

performed every two weeks is longer than the start-up or user invoked test. This test will

run for approximately fifteen seconds to measure the battery’s capability to provide an

acceptable amount of runtime. If the UPS fails a self test one of the LEDs will remain

illuminated indicating the type of problem. (see section 5 Troubleshooting)

English

OPERATION

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Minuteman UPS

Minuteman

Minuteman EN350 Manuale utente

Minuteman

Minuteman MBK 300YYY Manuale utente

Minuteman

Minuteman Endeavor RTXL Series Manuale utente

Minuteman

Minuteman E1000RM1U Manuale utente

Minuteman

Minuteman Continuous Power Series Manuale utente

Minuteman

Minuteman ED6000RMXFMR Manuale utente

Minuteman

Minuteman MBK-E SERIES Manuale utente

Minuteman

Minuteman Enspire Series Manuale utente

Minuteman

Minuteman 6-10KVA Tower Manuale utente

Minuteman

Minuteman PRO1100E Manuale utente

Minuteman

Minuteman Entrepid Series Manuale utente

Minuteman

Minuteman Endeavor ED1000RTXL2U Manuale utente

Minuteman

Minuteman Endeavor ED6000T Manuale utente

Minuteman

Minuteman XRT Series Manuale utente

Minuteman

Minuteman Enterprise Plus LCD RTXL UPS Series Manuale utente

Minuteman

Minuteman AT1200 Manuale utente

Minuteman

Minuteman Pro Series Manuale utente

Minuteman

Minuteman EN750 Manuale utente

Minuteman

Minuteman Pro 2200r Manuale utente

Minuteman

Minuteman Encompass EC1000RT2U Manuale utente

Minuteman

Minuteman Smart Up Series Manuale utente

Minuteman

Minuteman ETR550LCD Manuale utente

Minuteman

Minuteman SentryII UPS Manuale utente

Minuteman

Minuteman PARASHIELD 1224 Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente