Mircom TAS-2000 Series Manuale utente
Canada
25 Interchange Way
Vaughan, ON L4K 5W3
Tel: 905-660-4655 Fax: 905-660-4113
© Mircom 2004
Printed in Canada
Subject to change without prior notice
www.mircom.com
TAS-2000 Series
MSW-003 Software
LT-880 Rev. 1
September 2004
User Guide
Advanced Life Safety Solutions Advanced Life Safety Solutions
U.S.A.
60 Industrial Parkway
Cheektowaga, NY 14227
Tel: 1-888-660-4655 Fax: 1-888-660-4113
3
5
4
7
9
0
8
TAS-2000 MSW-003 Software Manual
i
Contents
Installing the Software ................................................................ 1
Connecting the Hardware ........................................................... 1
Direct Connect Method (using the RS-485IMA)....................... 1
Dial-Up Method (Using Modem)............................................... 1
Opening/creating A Job File....................................................... 2
Creating an ADC Tenant Database ............................................ 3
Creating an NSL Tenant Database ............................................ 5
Establishing a Direct Connection .............................................. 7
For Direct Cable Connection Operation ................................... 7
Establishing a Modem Connection............................................ 9
For Modem (MDM-1000A) Operation....................................... 9
Uploading Data (Lobby Panel to PC) ......................................... 11
Downloading Data (PC to Lobby Panel) .................................... 12
Changing Lobby Panel Parameters........................................... 13
Troubleshooting Guide............................................................... 14
Port is Already Used................................................................. 14
No System Detected................................................................. 14
Runtime Error ‘3024’................................................................. 14
ii
TAS-2000 MSW-003 Software Manual
1
Installing the Software
To install the TAS-2000 MSW-003 Software,
• Run SETUP.EXE on the root directory folder of the MSW-003 CD, or
• Use the Windows Control Panel’s Add/Remove Programs’ install feature.
Follow the instructions on the screen. Once it is installed, you can run the
program by clicking Start->Programs->TAS 2000.
Connecting the Hardware
Direct Connect Method (using the RS-485IMA)
Connect the RS-485IMA to the PC serial port using the serial cable provided
with the RS-485IMA.
Connect the ribbon cable on the RS-485IMA to the TAS-2000 Lobby Panel via
the terminal marked RS-485 I/F. Connector designations are as follows.
• For the Slim-Line model, use connector “P2” located near the top left
corner of the main circuit board.
• For the standard model, use connector P3 located near the bottom left
corner of the main circuit board.
Dial-Up Method (Using Modem)
Connect the modem on your PC to a standard telephone line. Connect the
dedicated telephone line at the Lobby Panel to the telephone jack connector
on the MDM-1000A and connect the ribbon cable on the MDM 1000A module
to the TAS-2000 Lobby Panel via the terminal marked RS-485 I/F.
Connector designations are as follows.
• For Slim-Line model, use connector “P2” located near the top left corner
of the main circuit board.
• For Standard model, use connector P3 located near the bottom left corner
of the main circuit board.
Notes:
• If your lobby panel is configured as a Non-Subscriber Line (NSL),
skip to Creating an NSL Tenant Database on page 5.
• If using a MDM-1000A, ensure that JW1 is removed and jumpers
1 & 3 are installed.
Note: Ensure that JW1 is installed and jumpers 1 & 3 are removed
on the MDM-1000A.
Opening/creating A Job File
2
Opening/creating A Job File
1. Open the TAS-2000 software by clicking Start->Programs->TAS 2000.
You will be prompted for a User Name and Password (as shown below).
The default for both is “mircom”.
2. Type “mircom” in both spaces and click OK.
The Control Panel window displays.
3. Click “Open Job File” located in the upper left on Control Panel window.
The following window displays.
4. Select an existing file from the list or type a new file name in the File
name window.
5. Click Open.
Note: “mircom” must be type in all lower case letters.
TAS-2000 MSW-003 Software Manual
3
Creating an ADC Tenant Database
The name of the file that is opened displays across the top of the Control
Panel window. To enter tenant names click “Show ADC”. The following window
displays.
Records may be added, edited or deleted as desired. To add records, click the
“ADD” button. The following window displays.
• Enter resident name if using scrolling directory panels, or leave blank if
using non-scrolling panels
• Enter resident apartment number (this is optional because it is used for
reference only--it will not be stored on lobby panel)
• Enter 4-digit resident dial code (for dial codes fewer than 4 digits, precede
with 0’s, e.g. 0003)
• Enter resident telephone number (maximum 14 digits)
Note: If your lobby panel is configured as a Non-Subscriber Line
(NSL), skip to Creating an NSL Tenant Database on page 5.
Creating an ADC Tenant Database
4
• Enter resident keyless code (this is optional because it is used for
reference only--it will not be stored on lobby panel)
• Enter default elevator code-If feature not used, enter 99
• Select default elevator ID-If feature not used, select ID-099
• Select lobby ID-factory default set as ID-001
• Click OK when finished.
In addition, you may use the Auto-Program feature by clicking the “Auto”
button in the ADC Database window. The following window displays:
• Enter number of residents to program (shown as 25)
• Enter default resident name (shown as Resident Name)
• Enter 4-digit starting dial code (shown as 1001)
• Enter starting keyless code (this is optional because it is used for
reference only--it will not be stored on lobby panel) (shown as 2001)
• Enter default elevator code-If feature not used, enter 99 (shown as 99)
• Select default elevator ID-If feature not used, select ID-099 (shown as
ID-099)
• Enter default phone # (shown as 9055551212)
• Click OK when finished
Note: When finished programming tenant records, skip to
Establishing a Direct Connection on page 7.
TAS-2000 MSW-003 Software Manual
5
Creating an NSL Tenant Database
The name of the file that is opened displays across the top of the Control
Panel window. To enter tenant names click “Show NSL”.
Records may be Added, Edited or Deleted as desired. To add records, click
the “ADD” button. The following window displays.
Note: If your lobby panel is configured as an Auto-Dialer (ADC), go
to Creating an ADC Tenant Database on page 3.
Creating an NSL Tenant Database
6
• Enter resident name if using scrolling directory panels, or leave blank if
using non-scrolling panels
• Enter resident apartment number (this is optional because it is used for
reference only--it will not be stored on lobby panel)
• Enter 4-digit resident dial code (for dial codes fewer than 4 digits, precede
with 0’s, e.g. 0003)
• Enter resident relay code (is determined by location of wires on BIX block)
• Enter resident keyless code (this is optional because it is used for
reference only--it will not be stored on lobby panel)
• Enter elevator code-If feature not used, enter 99
• Select ring pattern
• Select lobby ID-factory default set as ID-01
• Select NSL-ID, factory default set as ID-02
• Select default elevator ID-If feature not used, select ID-99
• Click OK when finished
In addition you may use the Auto-Program feature by clicking the “Auto”
button in the NSL Database window. The following window displays:
• Enter number of residents to program (shown as 25)
• Enter default resident name (shown as John Smith)
• Enter 4-digit starting dial code (shown as 1001)
• Enter starting keyless code (this is optional because it is used for
reference only--it will not be stored on lobby panel) (shown as 2001)
• Enter default elevator code-If feature not used, enter 99 (shown as 99)
• Select default elevator ID-If feature not used, select ID-99 (shown as
ID-099)
• Select default Lobby-ID (shown as ID-02)
• Enter starting relay code (shown as 0000)
• Select default NSL-ID (shown as ID-002)
Altri manuali per TAS-2000 Series
2
Indice
Altri manuali Mircom Sistema di interfono
Mircom
Mircom TX3-TOUCH-F15-B Manuale utente
Mircom
Mircom TX3 Nano Manuale utente
Mircom
Mircom Autodialer ADC Series Manuale utente
Mircom
Mircom TX3 Series Manuale utente
Mircom
Mircom TX3-TOUCH-S15B-WR Manuale utente
Mircom
Mircom TX3 Series Manuale utente
Mircom
Mircom EP-1000 Manuale utente
Mircom
Mircom RA-1000 Series Manuale utente
Mircom
Mircom TX3-TOUCH-F15-B Manuale utente
Mircom
Mircom TX3 Series Manuale utente
Mircom
Mircom TX3 Series Foglio di istruzioni
Mircom
Mircom TX3 Series Manuale del proprietario
Mircom
Mircom TX3-TOUCH-UPS-KIT Manuale utente
Mircom
Mircom TX3 Series Manuale utente
Mircom
Mircom TX3 Series Foglio di istruzioni
Mircom
Mircom RAM-216 Manuale utente
Mircom
Mircom TX3 Series Manuale del proprietario
Mircom
Mircom CA-1010 Manuale utente
Mircom
Mircom 9500 Series Istruzioni operative
Mircom
Mircom ADC Series Istruzioni operative
