Mitox MISHH Manuale utente
www.mitoxgm.co.uk
User and Assembly Manual
Saw Horse with Chainsaw Holder
Read this manual carefully before operating the product
Original Instructions Version March 12
Part No. MISHH
Read this manual carefully before operating the product
Original Instructions Version March 12
Thank you for purchasing this Mitox Saw Horse, we trust that you will be very
happy with your purchase.
Before you begin the assembly process, we recommend that you take a few
minutes to carefully read through this document and make yourself familiar
with your saw horse, doing so will assist you when undertaking its assembly,
and equally as importantly, provide you with a better understanding of how to
use it eectively and safely.
Read this manual carefully before operating the product
Original Instructions Version March 12
Instructions for Assembly
Position Part Quantity Position Part Quantity
1 Screw 8x30mm 8 8 Blanking Plate 1
2 Screw 8x35mm 6 9 Nut M8 17
3 Screw 8x45mm 2 10 Eye Bolt 12x30mm 1
4 Screw 8x70mm 1 11 Eye Bolt 10x20mm 1
5 Screw 10x20mm 1 12 End Cap 16mm 2
6 Cap Screw 8x12mm 6 13 Pin 5x10mm 2
7 R Clip 3mm 1
Read this manual carefully before operating the product
Original Instructions Version March 12
You will require –
- 1 x 13mm spanner or socket, (not supplied).
- 1 x 15mm spanner or socket, (not supplied).
- 1 x 6mm hex allen key, (this is supplied).
- A clean open space free of obstruction,
(this will aid the construction process).
Steps –
1. Attach the xed position legs, (item C), to plate (item F) using 4 x bolt (item 6).
Ensure that the slotted holes are facing outwards.
2. Attach a lower leg brace, (item D), to the assembled legs using 4 x bolt (item 1) and
4 nut (item 9), then secure the feet, (item L), using 1 x bolt (item 2) and 1 x nut (item 9).
3. Attach pivoting legs, (items A + B), to the xed position legs (item C), using 1 x bolt (item 2) and 1
x nut (item 9).
Note: the guide plate at the top of the pivot leg is on the outside face, then secure the feet, (item
L), using 1 x bolt, (item 2), and 1 x nut, (item 9). Ensure the bolts are tight, but still free enough to
allow the legs to pivot.
Read this manual carefully before operating the product
Original Instructions Version March 12
4. Attach pivoting plate, (item E), to the
assembled xed position legs (items C),
using 2 x bolt, (item 3), and 2 x nut, (item
9). Ensure the bolts are tight, but still allow
the plate to pivot freely.
5. Insert pivot clamp support, (item I), into
the top of the xed leg, (as shown in g 1),
then mount the measuring arm support,
(item H), using 1 x bolt, (item 5, then insert
the end cap, (item 8), into the top of the
other xed leg.
6. Insert the longer bar of the measuring arm,
(item G), into the measuring arm support,
(item H), insert the eye bolt, (item 11); to
secure the arm in place, then attach the
measuring arm ends caps, (item 12).
7. Attach the pivot clamp, (item J), to the
pivot clamp support, (item I), by inserting
clamps pin through the eye of the support,
then secure with the r-clip, (item 7), as
shown in g 2.
8. Attach the guide bar cover, (item K), to
the pivot clamp support, (item J), using 1 x
bolt, (item 4), and 1 x nut, (item 9). Ensure
the bolt is tight, but still allows the cover to
pivot freely.
9. Check that the saw horse is sturdy and that
all bolts are tightened.
Fig. 1
Fig. 2
I
G
JI
11
H
Read this manual carefully before operating the product
Original Instructions Version March 12
Attaching your Chainsaw
Carefully lower the chainsaw bar into position
between the two clamping blocks within
the pivot clamp, (item J), ensuring that there
is a minimum 2cm gap between the body
of the chainsaw and the clamp, (as shown
in g 3). Ensure that the bar is positioned at
approximately 90 degrees to the pivot clamp
and allows for access to your chainsaws
tensioning mechanism before tightening the
eyebolt, (item 10).
Insert the tensioning bar, (item M), through
the eyebolt, this allows you to apply sucient
pressure to rmly secure your chainsaw in
place. Once tightened, test the arc of travel;
ensure that the guide bar and chain doesn’t
make contact with any part of the saw horse.
Note: The pivot clamp, (item J), is mounted into a xed leg with an elongated slot. This slot allows
for vertical adjustment for the pivot clamp support; thus accommodating dierent sized guide
bars – the larger the bar, the higher the pivot clamp will need to be placed. Adjust the pivot
clamp so that the tip of the guide bar extends beyond the table, this should ensure that the log
will be cut completely through.
If you require the logs to be cut to a consistent length, set the measuring arm (item G) in the required
position, tightening the eyebolt, (item 11), using the tensioning bar, (item M) - see Fig.1 for details.
Fig. 3
Minimum Gap 2cm
Pivot Clamp
10
Read this manual carefully before operating the product
Original Instructions Version March 12
Key points for the safe use of the your saw horse
• Locatethewoodonthelogtable;pushingtheendtothemeasuringrodifrequired.Holdthe
wood down rmly with your left hand; ensure that your hand is kept well clear of the cutting
edge of the chainsaw, and from the cutting arc of the chainsaw.
• DONOTexceedtherecommendloadsthissawhorseisdesignedfor:
1. Lengths to a maximum of 1.80 mtrs.
2. A maximum diameter of 25cm
3. The maximum permissible load on the sawhorse is 120kg.
• Thechainguardonthissawhorseisdesignedforchainsawswithacuttingbarnotlongerthan
45cm/18”. A chainsaw with a cutting bar longer than 45cm/18”(which protrudes beyond the
chain guard) is not recommended.
• Alwaysdetachthepivotclampandguardfromthechainsawwhenusingtheseparatelyfromthe
saw horse.
• Ensurethepivotclamptensioneyeboltisfullytensionedusingthetensioningbar(itemM)and
that the chainsaw is fully secured before each use. Check frequently.
• Ensurethepivotclampandsupportsarekeptwelllubricated.
• Ensurethatyourworkareaisclearofobstaclesandthattherearenochildrenoranimalsnear
when using this saw horse.
• Alwaysensurethatyoursawhorseispositionedonastablelevelsurface,alsoallowingforyour
own sure footing.
• Werecommendthatyoucheckthemechanicalconditionofyoursawhorseregularly.Checkthe
tensioning of the screws, replace any parts that shown signs of damage, are worn or missing. Do
not use the saw horse until these parts have either been repaired or replaced, as it may not be
safe to do so.
• Whenusingyoursawhorseinconjunctionwithachainsaw,allowsensurethatappropriate
safety clothing is worn. A minimum of Chainsaw Gloves, Chainsaw safety helmet, (complete with
face and hearing protection), and protective leggings/trousers are recommended. Steel toe cap
shoes and chainsaw safety boots are also advised to protect your feet from falling logs, etc.
Read this manual carefully before operating the product
Original Instructions Version March 12
For more information on the Mitox® range of garden products please visit our website:
www.mitoxgm.co.uk
Indice
Altri manuali Mitox Sega
