Mitsubishi Electric RC-380P1 Manuale utente

Contents

Supported projectors:

XD365U-EST, WD385U-EST

Supported projectors are subject to change without notice.

Safety precautions ......................2

Using precautions .......................3

Introduction .................................6

What’s included in the box..........6

Overview......................................6

Preparations ................................7

Operation.....................................8

Troubleshooting.........................11

Speciﬁcations............................12

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS

This User Manual is important to you.

Please read it before using your interactive pen.

INTERACTIVE PEN

MODEL

RC-380P1

User Manual

EN-2

Safety precautions

WARNING:

When you use the interactive pen, be sure to put the strap on your wrist. Do not wave the

interactive pen with the strap put on your wrist.

If the strap is not used properly, the interactive pen may slip from your hand and hit other

people, resulting in injury. Even when the strap is put on your wrist, if you wave the interactive

pen, the strap may be cut and the interactive pen may hit other people, resulting in injury.

Do not throw the interactive pen, especially towards any person.

It causes injury.

Do not use the interactive pen if it is damaged by falling from on high or stepping upon it.

The damaged part causes injury.

Never remove the cabinet.

Please contact your dealer when you want to ﬁx, adjust, or inspect the interactive pen.

Do not modify this equipment.

It can lead to ﬁre or electric shock.

Place of installation

For safety’s sake, do not use the interactive pen at any place subjected to high temperature

and high humidity. Please maintain an operating temperature, and humidity as speciﬁed below.

• Operating temperature: between +41°F (+5°C) and +95°F (+35°C)

• Operating humidity: between 30% and 90%

• Never put any heat-producing device under the interactive pen to prevent the interactive pen

from being overheated.

• Do not install the interactive pen near any equipment that produces a strong magnetic ﬁeld.

Also refrain from installing the interactive pen near any cable carrying a large amount of

current.

• Do not place the interactive pen in the following places. Otherwise, a short circuit, heat

generation, or melting of the power cord coating may occur, causing ﬁre, electric shock,

product failure, or deformation.

• Outdoors or non air-conditioned place

• Place where a gas such as a hydrogen sulﬁde is generated (i.e. hot spring)

• Place where there is too much salt such as near the coast

CAUTION:

• Do not use the interactive pen near water or in contact with water. Do not touch the

interactive pen with wet hands. In addition, do not use the interactive pen with condensation

on it. The intrusion of water may cause damage or other failures.

• Use of a battery of wrong type may cause explosion.

• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

• Dispose of used batteries according to your local regulations.

• Batteries may explode if misused. Do not recharge, disassemble, or dispose of in ﬁre.

• Be sure to handle the battery according to the instructions.

• Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on

the interactive pen.

• Keep batteries out of reach of children and pets.

• Remove the battery, if the interactive pen is not used for a long time.

• Do not combine a new battery with an old one.

• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If

the solution comes in contact with your eyes, rinse them with water and then consult your

doctor.

EN-3

ENGLISH

Using this interactive pen may cause damage to the screen surface depending on the screen

used. In such a case, replace the screen with that having a solid surface.

When using the device in Europe:

COMPLIANCE NOTICE

This device complies with the requirements of the EC Directive 1999/5/EC “R&TTE Directive”.

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in

residential areas, on business and light industrial premises and on small-scale enterprises,

inside as well as outside of the buildings.

Using precautions

• Do not use the interactive pen in the following locations and manners, which may cause ﬁre

or electric shock.

• In a dusty or humid place.

• In an oily, smoky, or damp place such as a kitchen.

Note: This symbol mark is for EU countries only.

This symbol mark is according to the directive 2002/96/EC Article 10 Information

for users and Annex IV, and/or to the directive 2006/66/EC Article 20 Information

for end-users and Annex II.

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials

and components which can be recycled and/or reused.

This symbol means that electrical and electronic equipment, batteries and accumulators, at

their end-of-life, should be disposed of separately from your household waste.

If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means

that the battery or accumulator contains a heavy metal at a certain concentration. This will be

indicated as follows:

Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)

In the European Union there are separate collection systems for used electrical and electronic

products, batteries and accumulators.

Please, dispose of this equipment, batteries and accumulators correctly at your local

community waste collection/recycling centre.

Please, help us to conserve the environment we live in!

EN-4

Using precautions (continued)

For the U.S. and Canada only:

COMPLIANCE NOTICE OF FCC

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced Radio/TV technician for help.

Any changes or modiﬁcations not expressly approved by Mitsubishi could void the user’s

authority to operate this equipment.

COMPLIANCE NOTICE OF INDUSTRY CANADA

This Class B digital apparatus complies with Canadian ICES-003.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna

of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.

To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions:

(1)this device may not cause interference, and

(2)this device must accept any interference, including interference that may cause undesired

operation of the device.

For the U.S. and Canada only:

The wireless function of this device can be used only in the United States and Canada.

This function cannot be used legally in countries other than the above.

EN-5

ENGLISH

For Europe only:

The wireless function of this device can be used only in Austria, Bulgaria, Czech Republic,

Denmark, Finland, France, Germany, Greece, Hungary, Italy, Norway, Poland, Portugal,

Romania, Slovakia, Spain, Sweden, Switzerland, Ireland, United Kingdom, Belgium,

Netherlands, Luxembourg, Slovenia, Cyprus, Estonia, Iceland, Latvia, Lithuania, and Malta.

This function cannot be used legally in countries other than the above.

Hereby, Mitsubishi, declares that this device is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC.

Consult our European sales companies if you wish to conﬁrm the Declaration of Conformity

on this device. (Refer to the page “Mitsubishi Projector Warranty, Sales Support and Service

Information” for contact information.)

For Norway only:

In Norway, this device shall not be used in the geographical area within a radius of 20 km

from the centre of Ny-Alesund.

For Europe only:

The equipment was passed. The test was performed according to the following European

standards:

• EN 300 440-2 V1.4.1: 2010

• EN 301 489-1 V1.8.1: 2008

• EN 301 489-3 V1.4.1: 2002

• EN 62311: 2008

• EN 60950-1: 2006+A11: 2009+A1: 2010

Regulatory statement (R&TTE)

Operation of this device is subjected to the following National regulations and may be

prohibited to use if certain restriction should be applied.

You are cautioned that changes or modiﬁcations not expressly approved by the party

responsible for compliance could void your authority to operate the equipment.

EN-6

Interactive pen R03 (size-AAA) battery (2) Strap

User Manual

What’s included in the box

Overview

Using this interactive pen, you can perform the operation of the computer such as drawing a

line or clicking a button while projecting the image supplied from the computer.

Important:

• The interactive pen runs on the Windows XP, Windows Vista, and Windows 7 operating

systems only, not on Mac OS operating system software.

• Use a personal computer recommended by the application software to use the interactive

pen.

Pen tip L button

R button P (pairing) button

Power switch

Battery holder

BATTERY indicator

LINK indicator

Strap holder

Introduction

EN-7

ENGLISH

Installing the batteries to the interactive pen

Preparation:

Check that the power switch is turned OFF.

1. Push down the cover of the battery holder (), and then pull out the battery holder ().





2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).

• Use two R03 (size-AAA) batteries.

• Load the batteries from - spring side, and make sure to set them tightly.

3. Close the cover.





Attaching the strap



Preparations

EN-8

When operating the interactive pen, see also the manuals supplied with the projector and the

computer.

Preparation:

• Connect the projector to the computer using the USB cable supplied with the projector.

• Conﬁgure the settings for using the interactive pen in the menu of the projector.

• Project the image supplied from the computer.

Pen tip L button

R button P (pairing) button

Power switch

BATTERY indicator

LINK indicator

1. Turn the power switch to ON.

• The LINK indicator blinks red and the interactive pen starts searching for the operable

projector.

• When the projector is found, the LINK indicator illuminates in green or blinks rapidly,

showing that the computer is operable via the projector.

• When the projector isn’t found or the interactive pen isn’t operated for a certain period

of time, the LINK and BATTERY indicators illuminate in red and then go off, and the

interactive pen turns in low power mode.

2. Point the pen tip at the screen.

• See next page on how to hold the pen.

3. Operate the computer using the buttons described below while viewing the projected

images.

Button Function

L button This button works as the left button of a mouse. (When pressed, it works as

the click operation, and when the interactive pen is moved while the button is

pressed, it works as the drag operation.)

Pressing this button during the low power mode resumes the operation mode.

Pen tip When the pen tip is pushed to the projected screen, it works as pressing the L

button.

R button This button works as the right button of a mouse. (When pressed, it works as

the click operation, and when the interactive pen is moved while the button is

pressed, it works as the drag operation.)

Pressing this button during the low power mode resumes the operation mode.

P button When this button is held down, the mode of the interactive pen switches to the

pairing preparation mode.

When this button and the R button are held down at the same time, the pairing

setting is cancelled. (For the details of the pairing, see the User Manual supplied

with the projector.)

4. After the operation is completed, turn the power switch to OFF.

Operation

EN-9

ENGLISH

How to hold the interactive pen

Hold the interactive pen in the similar way as you hold a normal pen or a remote control.

Holding like a pen (when you operate the personal computer by pushing the pen tip to the

screen)

Don’t hold

around this

area.

Important:

• Push the pen tip diagonally to the screen. When you

push the pen tip vertically to the screen, lines may not

be drawn smoothly.

Incorrect

Correct

• Project images on a whiteboard or screen having

sufﬁcient hardness. When the hardness of the screen

is insufﬁcient, you cannot draw lines by pushing the

pen tip to the screen.

• The switch on the pen tip isn’t turned on and lines

cannot be drawn unless a force of approximately 200

gram is applied to the pen tip.

Holding like a remote control

Don’t hold around this area.

Important:

• The interactive pen does not work if its tip is in a shadow or if it is pointing at a shadow.

Correct (no shadow) Incorrect (shadow)

EN-10

Indicators

The condition of the interactive pen is notiﬁed by the illumination status of the BATTERY and

LINK indicators.

• When the pairing isn’t set

BATTERY LINK Condition

Off Blinking red

(repeating “blinks twice in 0.5 second

and goes off for 0.5 second”)

Searching the projector that can be operated

with the interactive pen

Off Steady green

or Blinking green

(rapidly)

Interactive pen is in operation.

Off Blinking red (once every 3 seconds)

Communicating with the projector*1

• When the pairing is set

BATTERY LINK Condition

Off Blinking red (four times a second)

During the pairing preparation mode (searching

for the projector to be paired with)

Off Blinking green (once a second) three

times

The pairing with the projector is established or

cancelled.

Off Steady green

or Blinking green

(rapidly)

Interactive pen is in operation.

Off Blinking red (once every 3 seconds)

Communicating with the projector*1

Off Blinking red ﬁve times

The supported projector isn’t detected during

the pairing preparation mode.

Off Blinking red (twice a second)

Searching the paired projector

• During the low power mode

BATTERY LINK Condition

Steady red Steady red

Shifting to the low power mode

Off Off

During the low power mode

• When the error occurs

BATTERY LINK Condition

Off Blinking red/green

Communication error occurs.

Turn off the power of the interactive pen once,

and after a few seconds, turn it on again.

*1: Such as the case that the Interactive Mode setting of the projector is turned Off while the interactive pen is

operated.

Operation (continued)

Altri manuali per RC-380P1

Indice

Lingue:

Altri manuali Mitsubishi Electric Accessori

Mitsubishi Electric

Mitsubishi Electric DPLS2 Manuale utente

Mitsubishi Electric

Mitsubishi Electric PZ-70CSW-E Manuale utente

Mitsubishi Electric

Mitsubishi Electric k-con KS9-BS1-A Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSENSOR Vision Sensor VS20 Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric KD Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric IQSS-R-E Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSENSOR VS70 Series Istruzioni utente

Mitsubishi Electric

Mitsubishi Electric EMU-CT100 Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSENSOR Vision Sensor VS20 Series Manuale di istruzioni

Mitsubishi Electric

Mitsubishi Electric KD Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric PAC-SH91MK-E Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSENSOR VS70 Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric Lossnay PZ-70CSW-E Guida rapida

Mitsubishi Electric

Mitsubishi Electric MELSENSOR Vision Sensor VS20M-11F310 Manuale di istruzioni

Mitsubishi Electric

Mitsubishi Electric PAC-SE41TS-E Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric KD Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric PZ-70CSB-E Guida rapida

Mitsubishi Electric

Mitsubishi Electric KD Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric R410A Manuale utente

Mitsubishi Electric

Mitsubishi Electric PAC-AK53BC Manuale utente

Mitsubishi Electric

Mitsubishi Electric Melsensor FA-CF26-SR Manuale di servizio

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente