Mitsubishi Electric AJ65BT-D75P2-S3 Manuale utente

AJ65BT-D75P2-S3 Positioning Module

User's Manual

A - 1

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of

the programmable controller system, refer to the user's manual for the CPU module used.

In this manual, the safety instructions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

A - 2

[Design Precautions]

WARNING

Failure to observe this could lead to accidents for incorrect outputs or malfunctioning.

Configure safety circuits external to the programmable controller to ensure that the entire

system operates safely even when a fault occurs in the external power supply or the

programmable controller.

Failure to do so may result in an accident due to an incorrect output or malfunction.

(1) Configure an emergency stop circuit and interlock circuit such as a positioning upper

limit/lower limit to prevent mechanical damage outside the programmable controller.

(2) The machine zero point return operation is controlled by the zero point return direction

and zero point return speed data. Deceleration starts when the near-point dog turns ON.

Thus, if the zero point return direction is incorrectly set, deceleration will not start and the

machine will continue to travel. Configure an interlock circuit to prevent mechanical

damage outside the programmable controller.

(3) When the positioning module detects an error, the motion slows down and stops or the

motion suddenly stops, depending on the stop group setting in parameter.

Set the parameters to meet the specifications of the positioning control system used.

In addition, set the OPR parameters and positioning data within the specified setting range.

When a data link results in a communication error, the operating status of the station in

communication error changes depending on the type of the used data link. Using the

communication status information, configure an interlock circuit in the sequence program to

ensure that the system will operate safely.

For the method of checking the station in communication error and its operating status at

communication error, refer to the corresponding data link manual.

[Design Precautions]

CAUTION

Do not install the control lines or communication cables together with the main circuit lines or

power cables.

Keep a distance of 100mm or more between them.

Failure to do so may result in malfunction due to noise.

A - 3

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications in

this manual.

Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of

the product.

Securely fix the module using the DIN rail or mounting screws and fully tighten the mounting

screws within the specified torque range. If the screws are loose, it may result in fallout, short

circuits, or malfunctions. Tightening the screw too far may cause damages to the screws and/or

the module, resulting in a fallout, short circuits, or malfunctions.

Securely connect the external device connection connector and peripheral device connection

connector into the module connector until a click is heard.

Improper connection could lead to a connection fault, and to incorrect inputs and outputs.

When not connecting the drive unit and peripheral device, always install a cover on the

connector section.

Failure to observe this could lead to malfunctioning.

[Wiring Precautions]

WARNING

Check the rated voltage and terminal layout before wiring to the programmable controller, and

connect the cables correctly. Connecting a power supply with a different voltage rating or

incorrect wiring may cause a fire or failure.

Check the terminal layout before wiring to the module, and connect the cables correctly.

Prevent foreign matter such as dust or wire chips from entering the module.

Such foreign matter can cause a fire, failure, or malfunction.

[Wiring Precautions]

!CAUTION

Tighten the terminal screws within the range of the specified torque.

If the terminal screws are loose, it may result in short circuits, or malfunctions. Tightening the

terminal screws too far may cause damages to the terminal screws and/or the module, resulting

in short circuits, or malfunctions.

Be sure there are no foreign substances such as sawdust or wiring debris inside the module.

Such debris could cause fires, failure, or malfunction.

Individually ground the FG terminal of the programmable controller with a ground resistance of

100 ohms or less. Failure to do so may result in malfunction.

Place the cables in a duct or clamp them.

If not, dangling cable may swing or inadvertently be pulled, resulting in damage to the module

or cables or malfunction due to poor contact.

Keep a certain distance between the control wires and the communication cables.

Noise can cause a malfunction.

When disconnecting a cable from the module, do not pull on the cable itself. Disconnect cables

not fitted with a connectors by holding and pulling the cable connector.

Disconnect cables not fitted with a connector by removing the screws from the part connected

to the module can cause damage to the module or cable, or ,malfunction due to cable

connection faults.

A - 4

[Startup and Maintenance Precautions]

!CAUTION

Do not touch any terminal while power is on.

Doing so will cause electric shock or malfunction.

Never disassemble or modify the module.

Failure to observe this could lead to trouble, malfunctioning, injuries or fires.

Switch off all phases of the externally supplied power used in the system before cleaning or

tightening the screws.

Failure to turn all phases OFF could lead to electric shocks.

Make sure to install or remove the module from the panel after switching off all phases of the

externally supplied power for the system.

Failure to turn all phases OFF could lead to module trouble or malfunctioning.

Before starting test operation, set the parameter speed limit value to the slowest value, and

make sure that operation can be stopped immediately if a hazardous state occurs.

Do not install/remove the terminal block more than 50 times after the first use of the product.

(IEC 61131-2 compliant)

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the module.

Failure to do so may cause a failure or malfunctions of the module.

[Precautions for use]

!CAUTION

Note that when the reference axis speed is designated for interpolation operation, the speed of

the partner axis (2nd axis) may be larger than the set speed (larger than the speed limit value).

[Disposal Precautions]

!CAUTION

When disposing of the product, handle it as industrial waste.

A - 5

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi representative

in your region.

A - 6

REVISIONS

*The manual number is given on the bottom left of the back cover.

Print Date * Manual Number Revision

Apr., 1998 IB (NA)-66824-A First printing

Apr., 2003 IB (NA)-66824-B Complete review

Oct., 2003 IB (NA)-66824-C Complete review

Feb.,2004 IB (NA)-66824-D

Partial correction addition

CONTENTS, Section 3.5, Section 5.6.2, Section 7.1.2, Section 8.2.5,

Section 8.2.6, Section 10.1.2, Section 10.3.3 to Section 10.3.5,

Section 10.3.8, Appendix 13, INDEX

Jun., 2005 IB (NA)-66824-E Partial correction addition

SAFETY INSTRUCTIONS, Generic Terms and Abbreviations,

Section 3.4.2, Section 4.2.2, Section 4.3, Section 4.5.1, Section 4.5.3,

Section 4.8.1, Section 5.1.2, Section 5.2.1, Section 5.3, Section 5.7.2,

Section 6.1.1, Section 6.6.1, Section 6.6.5, Section 8.1.1,

Section 8.2.4 to Section 8.2.8, Section 8.5, Section 9.1.2,

Section 9.15, Section 9.2.6, Section 9.2.8 to Section 9.2.11,

Section 10.3.9, Section 11.3.1, Section 12.2.1, Section 14.4.3,

Section 12.4.4, Section 12.5.1, Section 12.5.2, Section 12.7.1,

Section 12.7.5, Section 12.7.6, Section 13.4, Section 14.2,

Section 14.3, Appendix 5.1, Appendix 11, Appendix 12

Jul., 2006 IB (NA)-66824-F Partial correction addition

Appendix 7.1, INDEX

Sep., 2007 IB(NA)-66824-G Partial revisions

Section 5.1.2, Section 5.2.1, Section 5.6.1, Section 5.7.1

Apr., 2015 IB(NA)-66824-H Addition

CONDITIONS OF USE FOR THE PRODUCT

Partial correction addition

SAFETY PRECAUTIONS, INTRODUCTION, ABOUT MANUALS,

COMPLIANCE WITH EMC AND LOW VOLTAGE DIRECTIVES,

GENERIC TERMS AND ABBREVIATIONS, Section 1.3, 2.3, 2.4, 3.1,

3.2, 3.7.1, 3.7.3, 3.7.4, 4.1.2, 4.1.3, 4.2.1, 4.3, 4.5.1, 4.5.2, 4.8.1,

5.1.1, 5.2.3, 5.3, 5.5, 6.1.1, 6.1.2, 9.1.4, 9.1.5, 9.2.7, 10.1.1, 10.1.2,

10.3.5, 10.3.8, 10.4.1, 10.4.2, 12.3.2, 12.4.3, 12.4.4, 12.5.3, 13.4,

Appendix 1, 2, 3.2, 5.1, 5.2, 5.3, 6.1, 7.1, 8.1, 9.1, 11, 12,

WARRANTY

Jun., 2017 IB(NA)-66824-I Partial correction addition

Appendix 8.1, 9.1, 12

Japanese Manual Version SH-3654-K

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.

Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which

may occur as a result of using the contents noted in this manual.

1998 MITSUBISHI ELECTRIC CORPORATION

A - 7

MEMO

A - 8

INTRODUCTION

Thank you for purchasing the Mitsubishi Electric general-purpose programmable controller MELSEC-A Series.

Always read through this manual, and fully comprehend the functions and performance of the A Series PLC

before starting use to ensure correct usage of this product.

When applying the program examples introduced in this manual to an actual system, ensure the applicability

and confirm that it will not cause system control problems.

CONTENTS

SAFETY PRECAUTIONS............................................................................................................................ A- 1

CONDITIONS OF USE FOR THE PRODUCT ........................................................................................... A- 5

REVISIONS .................................................................................................................................................. A- 6

INTRODUCTION.......................................................................................................................................... A- 8

CONTENTS.................................................................................................................................................. A- 8

ABOUT MANUALS .......................................................................................................................................A- 15

COMPLIANCE WITH EMC AND LOW VOLTAGE DIRECTIVES.........................................................A- 16

USING THIS MANUAL (1)............................................................................................................................A- 17

USING THIS MANUAL (2)............................................................................................................................A- 18

USING THIS MANUAL (3)............................................................................................................................A- 19

GENERIC TERMS AND ABBREVIATIONS ................................................................................................A- 20

ENCLOSED PARTS .....................................................................................................................................A- 21

SECTION 1 PRODUCT SPECIFICATIONS AND HANDLING

1. PRODUCT OUTLINE 1- 1 to 1- 20

1.1 Positioning control.................................................................................................................................. 1- 2

1.1.1 Features of D75P2 .......................................................................................................................... 1- 2

1.1.2 Purpose and applications of positioning control............................................................................. 1- 4

1.1.3 Mechanism of positioning control ................................................................................................... 1- 6

1.1.4 Outline design of positioning system .............................................................................................. 1- 8

1.1.5 Communicating signals between D75P2 and each module........................................................... 1- 10

1.2 Flow of system operation........................................................................................................................ 1- 12

1.2.1 Flow of all processes........................................................................................................................ 1- 12

1.2.2 Outline of starting ............................................................................................................................. 1- 14

1.2.3 Outline of stopping ........................................................................................................................... 1- 16

1.2.4 Outline for restarting......................................................................................................................... 1- 17

1.3 Outline of communication ....................................................................................................................... 1- 18

1.3.1 Cyclic transmission........................................................................................................................... 1- 19

1.3.2 Transient transmission ..................................................................................................................... 1- 20

2. SYSTEM CONFIGURATION 2- 1 to 2- 12

2.1 General image of system....................................................................................................................... 2- 2

2.2 List of configuration devices .................................................................................................................. 2- 4

2.3 Applicable system .................................................................................................................................. 2- 6

2.4 Precautions for use ................................................................................................................................ 2- 8

Altri manuali per AJ65BT-D75P2-S3

Indice

Altri manuali Mitsubishi Electric Controllori

Mitsubishi Electric

Mitsubishi Electric MELSEC FX3U-485ADP-MB Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELDAS MDS-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric RJ71PB91V-U-IN-E Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELFA BFP-A8787-F Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R16MTCPU Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX2NC-16EX-DS Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC-A Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric CR800 Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2N-4da Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC-Q00U(J)CPU Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric M800VS Series Guida all'installazione

Mitsubishi Electric

Mitsubishi Electric QJ71AS92 Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC-L02SCPU Manuale utente

Mitsubishi Electric

Mitsubishi Electric LCPU-U-HW Manuale di istruzioni

Mitsubishi Electric

Mitsubishi Electric MELSEC FX Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC FX-1HC Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JET MR-JET Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente