Mitsubishi Electric MELSEC Q Series Manuale utente

Q Corresponding MELSECNET/H

Network System

Reference Manual (Remote I/O network)

-QJ71LP21

-QJ71LP21-25

-QJ71LP21S-25

-QJ71LP21G

-QJ71LP21GE

-QJ71BR11

-QJ72LP25-25

-QJ72LP25G

-QJ72LP25GE

-QJ72BR15

A - 1 A - 1

• SAFETY PRECAUTIONS •

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of

the programmable controller system, refer to the user’s manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

• When the network develops a communication error, the station with the communication error will

enter into the following status.

Check the communication status information and configure an interlock circuit in the sequence

program to ensure that the entire system will operate safely. Failure to do so may result in an

accident due to an incorrect output or malfunction.

(1) The remote master station will hold the data from before the communication error.

(2) The remote I/O station turns off all outputs. The output module of the remote I/O station can

clear/hold the output status at the time of error by using the remote I/O module parameters.

As the parameters are set to "clear" by default, the output module turns off the outputs at the

time of error. If it is required to hold the output in order to operate the system safely, set the

parameters to "hold".

WARNING

CAUTION

A - 2 A - 2

[Design Precautions]

WARNING

• When connecting a peripheral with the programmable controller CPU or connecting a personal

computer with an intelligent function module to modify data of a running programmable

controller, configure an interlock circuit in the sequence program to ensure that the entire

system will always operate safely. For other forms of control (such as program modification or

operating status change) of a running programmable controller, read the relevant manuals

carefully and ensure that the operation is safe before proceeding. Especially, when a remote

programmable controller is controlled by an external device, immediate action cannot be taken if

a problem occurs in the programmable controller due to a communication failure. To prevent

this, configure an interlock circuit in the sequence program, and determine corrective actions to

be taken between the external device and CPU module in case of a communication failure.

• If a communication cable is disconnected, the network may be unstable, resulting in a

communication failure of multiple stations. Configure an interlock circuit in the program to ensure

that the entire system will always operate safely even if communications fail. Failure to do so

may result in an accident due to an incorrect output or malfunction.

CAUTION

• Do not install the control lines or communication cables together with the main circuit lines or

power cables. Keep a distance of 100mm or more between them. Failure to do so may result in

malfunction due to noise.

• Reset the CPU module or remote I/O module after changing its parameters. Failure to do so

may cause malfunction because the previous parameter settings remain in the module.

[Installation Precautions]

CAUTION

• Use the programmable controller in an environment that meets the general specifications in the

user’s manual for the CPU module used. Failure to do so may result in electric shock, fire,

malfunction, or damage to or deterioration of the product.

• To mount the module, while pressing the module mounting lever located in the lower part of the

module, fully insert the module fixing projection(s) into the hole(s) in the base unit and press the

module until it snaps into place. Incorrect mounting may cause malfunction, failure or drop of the

module. When using the programmable controller in an environment of frequent vibrations, fix

the module with a screw.

• Tighten the screws within the specified torque range. Undertightening can cause drop of the

screw, short circuit, or malfunction. Overtightening can damage the screw and/or module,

resulting in drop, short circuit, or malfunction

• Shut off the external power supply (all phases) used in the system before mounting/removing a

module or connecting/disconnecting a connector. Failure to do so may result in damage to the

product. Modules can be replaced online on a remote I/O station where a remote I/O module

with function version D or later is used. Note that there are restrictions on the modules that can

be replaced online, and each module has its predetermined replacement procedure. For details,

refer to the relevant section in this manual.

A - 3 A - 3

[Installation Precautions]

CAUTION

• Do not directly touch any conductive parts and electronic components of the module.

Doing so can cause malfunction or failure of the module.

[Wiring Precautions]

WARNING

• Shut off the external power supply (all phases) used in the system before installation and wiring.

Failure to do so may result in electric shock or damage to the product.

[Wiring Precautions]

CAUTION

• Individually ground the FG terminal of the programmable controller with a ground resistance of

100Ω or less.

Failure to do so may result in electric shock or malfunction.

• Check the rated voltage and terminal layout before wiring to the module, and connect the cables

correctly. Connecting a power supply with a different voltage rating or incorrect wiring may

cause a fire or failure.

• Connectors for external devices and coaxial cables must be crimped or pressed with the tool

specified by the manufacturer, or must be correctly soldered. Incomplete connections may

cause short circuit, fire, or malfunction.

• Place the cables in a duct or clamp them. If not, dangling cable may swing or inadvertently be

pulled, resulting in damage to the module or cables or malfunction due to poor contact.

• Tighten the terminal screws within the specified torque range. Undertightening can cause short

circuit, fire, or malfunction. Overtightening can damage the screw and/or module, resulting in

drop, short circuit, or malfunction.

• When disconnecting the cable from the module, do not pull the cable by the cable part. For the

cable with connector, hold the connector part of the cable. For the cable connected to the

terminal block, loosen the terminal screw. Pulling the cable connected to the module may result

in malfunction or damage to the module or cable.

• Prevent foreign matter such as dust or wire chips from entering the module. Such foreign matter

can cause a fire, failure, or malfunction.

• A protective film is attached to the top of the module to prevent foreign matter, such as wire

chips, from entering the module during wiring.

Do not remove the film during wiring.

Remove it for heat dissipation before system operation.

• Mitsubishi Electric programmable controllers must be installed in control panels. Connect the

main power supply to the power supply module in the control panel through a relay terminal

block. Wiring and replacement of a power supply module must be performed by qualified

maintenance personnel with knowledge of protection against electric shock. For wiring methods,

refer to the QCPU User's Manual (Hardware Design, Maintenance and Inspection).

A - 4 A - 4

[Setup and Maintenance Precautions]

WARNING

• Do not touch any terminal while power is on. Doing so will cause electric shock or malfunction.

• Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal screws or module fixing screws.

Failure to do so may result in electric shock or cause the module to fail or malfunction.

[Setup and Maintenance Precautions]

CAUTION

• Before performing online operations (especially, program modification, forced output, and

operating status change) for the running CPU module on another station from GX Developer

over the MELSECNET/H network, read relevant manuals carefully and ensure the safety.

Improper operation may damage machines or cause accidents.

• Do not disassemble or modify the modules.

Doing so may cause failure, malfunction, injury, or a fire.

• Use any radio communication device such as a cellular phone or PHS (Personal Handy-phone

System) more than 25cm away in all directions from the programmable controller.

Failure to do so may cause malfunction.

• Shut off the external power supply (all phases) used in the system before mounting/removing a

module or connecting/disconnecting a connector. Failure to do so may cause the module to fail

or malfunction. Modules can be replaced online in a remote I/O network system where a remote

I/O module with function version D or later is used. Note that there are restrictions on the

modules that can be replaced online, and each module has its predetermined replacement

procedure. For details, refer to the relevant section in this manual.

• After the first use of the product, do not mount/remove the module to/from the base unit more

than 50 times (IEC 61131-2 compliant).

Exceeding the limit of 50 times may cause malfunction.

• Before handling the module, touch a conducting object such as a grounded metal to discharge

the static electricity from the human body.

Failure to do so may cause the module to fail or malfunction.

[Disposal Precautions]

CAUTION

• When disposing of this product, treat it as industrial waste.

A - 5 A - 5

• CONDITIONS OF USE FOR THE PRODUCT •

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

 Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

 Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

 Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A - 6 A - 6

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Oct., 2000 SH (NA) -080124-A First printing

May., 2001 SH (NA) -080124-B Model addition

QJ71LP21G, QJ72LP25G, QJ71LP21GE, QJ72LP25GE

Correction

Product Components, About The Generic Terms And Abbreviations,

Chapter 1, Section 1.2, 2.4, 3.1.1, 3.1.2, 3.2.1, 3.2.2, 3.3.2, 4.2.1, 4.2.2,

4.8.2, Chapter 5, Section 5.1.5, 5.2.1, 6.1.2, 6.2.1, 6.3, 6.4, 7.1.1, 7.8,

8.1, 8.1.1, 8.1.4, 8.3.1, 8.3.2, Appendix 2, 3, 4, 5, Index

Addition

Section 8.2.6

Apr., 2002 SH (NA) -080124-C Correction

Section 1.2, 1.3, 2.3.1, 2.3.2, 2.3.3, 2.5, 3.1.1, 3.1.2, 3.2, 3.3.2, 4.2.1,

6.1.1, 6.4, Chapter 7, Section 8.4, Appendix 2, 3

Changed item numbers

Section 2.3 Section 2.4, Section 2.4 Section 2.5

Addition

Section 7.10

Nov., 2002 SH (NA) -080124-D Model addition

QJ71LP21S-25

Correction

SAFETY PRECAUTIONS, CONTENTS,

Generic Terms And Abbreviations, Product Components,

Section 1.1, 1.2, 3.1.1, 3.1.2, 4.1.2, 4.8.1, 4.8.2, 7.1.1, 8.1.4,

Appendix 2, 3

Apr., 2003 SH (NA) -080124-E Correction

SAFETY PRECAUTIONS, About Manuals, Section 1.2, 2.1.2, 2.2.2,

2.3.2, 2.5, 3.1.1, 3.1.2, 3.2.2, 3.3.1, Chapter 5, Section 5.1.3, 5.1.5, 6.2,

6.3, 6.4, 6.5, 8.1, 8.2, 8.2.1, 8.2.5, 8.3.1

A - 7 A - 7

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Jun., 2004 SH (NA) -080124-F Correction

SAFETY PRECAUTIONS, Manuals, Generic Terms And Abbreviations,

Section 1.2, 2.1.2, 2.2.2, 2.3.2, 2.4.2, 2.5, 3.1.1, 3.1.2, 3.1.3, 3.1.4, 3.2,

3.2.2, 4.2.2, 4.9.1, 4.10, 4.10.1, 4.10.2, 4.10.3, Chapter 5, Section 5.1.1,

5.2, 5.2.1, 6.4, 6.5, Chapter 7, Section 8.1, 8.1.1, 8.1.2, 8.1.3, 8.1.4,

8.2.1, 8.2.3, 8.2.5, 8.2.7, 8.3.1, 8.3.2, Appendix 2, 3

Addition

Section 1.4, 2.4, 2.7, 3.3.3, 3.3.4, 7.11, 7.12, 8.2.7, Appendix 7

Changed section No.

Section 2.4 Section 2.5, Section 2.5 Section 2.6

Mar., 2005 SH (NA) -080124-G Correction

Safety Precautions, Conformation to the EMC Directive and Low Voltage

Instruction, Product Configuration, Section 1.1, 1.2, 2.6, 2.7, 3.1.1, 3.1.2,

3.1.4, 3.2.2, 3.3.2, 4.2.1, 4.2.2, 4.3, 4.4, 4.8.1, 4.8.2, 4.9.1, 4.10.1, 5.1.4,

6.1.1, 6.2, 6.2.2, 6.3, 7.4, 8.1, 8.1.2, 8.1.3, 8.2, 8.2.1, 8.3.1, 8.3.2,

Appendix 2, 3, 4, 5, 7

Addition

Section 8.2.8

Sep., 2005 SH (NA) -080124-H Correction

Generic Terms And Abbreviations, Section 1.2, Section 2.5, Section 3.2,

3.2.2, 3.3.2, Section 5.1.5, 5.2.1, Section 6.3, 6.5, Section 7.12, Section

8.2, 8.2.5, 8.3.1, 8.3.2, Appendix 3, 4, 5

May, 2006 SH (NA) -080124-I Correction

Generic Terms And Abbreviations, Section 1.1, Chapter 2, Section 2.2.1,

2.5, 3.1.1, 3.1.4, 4.2.1, 4.2.2, 5.1.3, 5.1.4, 5.1.5, 6.3, 6.4, 7.1.1, 8.1.2,

8.3.2, Appendix 5

Addition

Section 2.5.1, 2.5.2

Sep., 2006 SH (NA) -080124-J Correction

Section 2.1.2, 2.2.2, 2.3.2, 2.4.2, 4.2.1, 4.2.2, 8.3.2

A - 8 A - 8

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Nov., 2006 SH (NA) -080124-K Addition

SAFETY PRECAUTIONS

Correction

Section 2.5.2, 3.2.2, 4.2.1, 4.2.2, 4.3, 4.8.1, 4.8.2, 5.1.5, 8.1.2, 8.2, 8.2.4,

8.3.2, Appendix 2, 3, 5

Sections added

Section 8.2.8, 8.4, 8.5

Changed section No.

Section 8.2.8 Section 8.2.9, Section 8.4 Section 8.6

Oct., 2007 SH (NA) -080124-L Addition

Chapter 1, Section 2.1.2, 2.2.2, 2.3.2, 2.4.2, 2.5.1, 2.5.2, 2.7, 3.3.1, 3.3.2,

4.8.2, Chapter 5, Section 5.1.4, 5.1.5, 8.2.1, 8.3.1, Appendix 2, 4, 5

Correction

SAFETY PRECAUTIONS , Generic Terms And Abbreviations, Section

2.2.1, 2.3.1, 2.4.1, 4.2.1, 4.7.1, 4.7.2, 4.7.3, 4.9.1, 5.1.1, 5.1.3, 6.1.1, 6.2,

6.3, 6.5, 6.6, 7.1.1, 7.12, 8.1, Appendix 3

Sections added

DEFINITIONS OF TERMINOLOGY, Section 6.4

Changed section No.

Section 6.4 to 6.5 Section 6.5 to 6.6, Appendix 7 Appendix 6

Feb., 2008 SH (NA)-080124-M Correction

Generic Terms And Abbreviations, Section 1.2, 2.1.2, 2.2.2, 2.3.2, 2.4.2,

2.5, 3.2.2, 3.3.2, 4.7, 4.8, 4.9.1, 5.1.1, 5.1.4 to 5.1.6, 5.2.1, 6.1.1, 6.5, 6.6,

7.1.1, 7.8, 7.11.4, 8.1, 8.3, 8.4, Appendix 2, 3, 5

Sep., 2008 SH (NA)-080124-N Correction

SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage

Directives, Generic Terms And Abbreviations, DEFINITIONS OF

TERMINOLOGY, Chapter1, Section 1.2, 1.3, 2.1.2, 2.1.3, 2.2, 2.2.1,

2.2.3, 2.3, 2.4.2, 2.4.3, 2.5.1, 2.6, 3.1.4, 3.2, 3.3.2, 3.3.4, 4.2.1, 4.2.2, 4.8,

4.9.1, Chapter 5, Section 5.1.3 to 5.1.5, 6.1.2, 6.5, 6.6, Chapter 7, 7.1.1,

7.10, 7.11, 7.11.1, 7.11.3, 7.11.4, Chapter 8, 8.1, 8.2, 8.2.5, 8.2.7, 8.3.1,

8.3.2, Appendix 2 to 6

Altri manuali per MELSEC Q Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Mitsubishi Electric Controllori

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5UC-96MT/D Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric Melsec-Q172DCPU Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R16MTCPU Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSENSOR MELSEC iQ-R MH11H01A0SNA Manuale utente

Mitsubishi Electric

Mitsubishi Electric a2 Series Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric FX3U-1PSU-5V Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX2N-10PG Manuale utente

Mitsubishi Electric

Mitsubishi Electric R60AD8-G Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q173CPU Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC-L Series LD40PD01 Manuale utente

Mitsubishi Electric

Mitsubishi Electric GB-24A Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC-F FX-16E-TB Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC-Q QnPHCPU Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric CR800 Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric Central Controller G-50A Manuale utente

Mitsubishi Electric

Mitsubishi Electric AnyWire NZ2AW1C2AL Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric TC-24B Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente