Mitsubishi Electric NZ2GF2BN-60DA4 Manuale utente

CC-Link IE Field Network Digital-Analog Converter

Module

User's Manual

-NZ2GF2BN-60DA4

-NZ2EX2B-60DA4

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full attention

to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of the

programmable controller system, refer to the user's manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

●When a communication failure occurs in the network, data in the master module are held. Check Data

link status (each station) (SW00B0 to SW00B7) and configure an interlock circuit in the program to

ensure that the entire system will operate safely.

●Do not use any “use prohibited” signals as a remote I/O signal. Do not write any data to the "use

prohibited" areas in the remote register. If these operations are performed, correct operation of the

module cannot be guaranteed.

●Configure safety circuits external to the programmable controller to ensure that the entire system

operates safely even when a fault occurs in the external power supply or the programmable controller.

Failure to do so may result in an accident due to an incorrect output or malfunction.

(1) The status of analog output depends on the setting of various functions that control the analog

output. Exercise great caution when setting those functions. For details of the status of analog

output, refer to Page 92, Section 8.7.

(2) Due to failure of the output element or internal circuit, normal output may not be obtained

correctly. Configure an external circuit for monitoring output signals that could cause a serious

accident.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

[Design Precautions]

[Installation Precautions]

[Wiring Precautions]

CAUTION

●Do not install the control lines or communication cables together with the main circuit lines or power

cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction

due to noise.

●At power-on/off, a voltage may occur or a current may flow between output terminals for a moment. In

this case, start the control after analog outputs become stable.

WARNING

●Shut off the external power supply (all phases) used in the system before mounting or removing a

module. Failure to do so may result in electric shock or cause the module to fail or malfunction.

CAUTION

●Use the module in an environment that meets the general specifications in this manual. Failure to do

so may result in electric shock, fire, malfunction, or damage to or deterioration of the product.

●Do not directly touch any conductive parts and electronic components of the module. Doing so can

cause malfunction or failure of the module.

●After the first use of the product, do not connect/remove the extension module more than 50 times

(IEC 61131-2 compliant). Exceeding the limit may cause malfunction.

●To connect an extension module to a main module, engage the respective connectors and securely

lock the module joint levers. Incorrect interconnection may cause malfunction, failure, or drop of the

extension module.

●Securely connect the cable connectors. Poor contact may cause malfunction.

WARNING

●Shut off the external power supply (all phases) used in the system before wiring. Failure to do so may

result in electric shock or cause the module to fail or malfunction.

CAUTION

●Individually ground the FG terminal of the programmable controller with a ground resistance of 100

ohms or less. Failure to do so may result in electric shock or malfunction.

●Tighten any unused terminal screws within the specified torque range. Undertightening can cause a

short circuit due to contact with a solderless terminal.

[Wiring Precautions]

[Startup and Maintenance Precautions]

CAUTION

●Use applicable solderless terminals and tighten them within the specified torque range. If any spade

solderless terminal is used, it may be disconnected when a terminal block screw comes loose,

resulting in failure.

●Check the rated voltage and terminal layout before wiring to the module, and connect the cables

correctly. Connecting a power supply with a different voltage rating or incorrect wiring may cause a fire

or failure.

●Tighten the terminal block screws within the specified torque range. Undertightening can cause short

circuit, fire, or malfunction. Overtightening can damage the screw and/or module, resulting in drop,

short circuit, fire, or malfunction.

●Prevent foreign matter such as dust or wire chips from entering the module. Such foreign matter can

cause a fire, failure, or malfunction.

●Place the cables in a duct or clamp them. If not, dangling cable may swing or inadvertently be pulled,

resulting in damage to the module or cables or malfunction due to poor contact.

●Do not install the control lines or communication cables together with the main circuit lines or power

cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction

due to noise.

●When disconnecting the cable from the module, do not pull the cable by the cable part. For the cable

with connector, hold the connector part of the cable. For the cable connected to the terminal block,

loosen the terminal screw. Pulling the cable connected to the module may result in malfunction or

damage to the module or cable.

●When an overcurrent caused by an error of an external device or a failure of the programmable

controller flows for a long time, it may cause smoke and fire. To prevent this, configure an external

safety circuit, such as a fuse.

●Mitsubishi Electric programmable controllers must be installed in control panels. Wiring and

replacement of a module must be performed by qualified maintenance personnel with knowledge of

protection against electric shock. For wiring methods, refer to "INSTALLATION AND WIRING" in this

manual.

WARNING

●Do not touch any terminal while power is on. Doing so will cause electric shock or malfunction.

●Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal block screws or connector screws. Failure to do so may cause the module to

fail or malfunction.

[Startup and Maintenance Precautions]

[Disposal Precautions]

CAUTION

●Do not disassemble or modify the module. Doing so may cause failure, malfunction, injury, or a fire.

●Do not drop or apply strong shock to the module. Doing so may damage the module.

●Shut off the external power supply (all phases) used in the system before mounting or removing a

module. Failure to do so may cause the module to fail or malfunction.

●After the first use of the product, do not connect/remove the terminal block more than 50 times (IEC

61131-2 compliant). Exceeding the limit may cause malfunction.

●Before handling the module or connection cables, touch a conducting object such as a grounded

metal to discharge the static electricity from the human body. Failure to do so may cause the module

to fail or malfunction.

●Startup and maintenance of a control panel must be performed by qualified maintenance personnel

with knowledge of protection against electric shock. Lock the control panel so that only qualified

maintenance personnel can operate it.

CAUTION

●When disposing of this product, treat it as industrial waste.

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or serious accident;

and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the PRODUCT for the

case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED TO ANY AND ALL

RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY

INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE

OPERATED OR USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR

WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL

BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any other cases in which the

public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of a special quality

assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator and Escalator,

Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for Recreation and Amusement, and

Safety devices, handling of Nuclear or Hazardous Materials or Chemicals, Mining and Drilling, and/or other

applications where there is a significant risk of injury to the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the PRODUCT in one or

more of the Prohibited Applications, provided that the usage of the PRODUCT is limited only for the specific

applications agreed to by Mitsubishi and provided further that no special quality assurance or fail-safe, redundant or

other safety features which exceed the general specifications of the PRODUCTs are required. For details, please

contact the Mitsubishi representative in your region.

INTRODUCTION

Thank you for purchasing the CC-Link IE Field Network digital-analog converter module (hereafter abbreviated as D/A

converter module).

This manual describes the procedures, system configuration, parameter settings, functions, and troubleshooting of a

D/A converter module.

Before using this product, please read this manual and the relevant manuals carefully and develop familiarity with the

functions and performance of the D/A converter module to handle the product correctly.

When applying the program examples introduced in this manual to an actual system, ensure the applicability and

confirm that it will not cause system control problems.

Relevant modules: NZ2GF2BN-60DA4, NZ2EX2B-60DA4

Remark

Unless otherwise specified, this manual describes the program examples in which the remote I/O signals and remote

registers are assigned for a D/A converter module as follows.

• Remote input signal: RX0 to RX1F (main D/A converter module), RX20 to RX2F (extension D/A converter

module)

• Remote output signal: RY0 to RY1F (main D/A converter module), RY20 to RY2F (extension D/A converter

module)

• Remote register (RWr): RWr0 to RWrF (main D/A converter module), RWr10 to RWr1F (extension D/A converter

module)

• Remote register (RWw): RWw0 to RWwF (main D/A converter module), RWw10 to RWw1F (extension D/A

converter module)

For the assignment of remote I/O signals and remote registers, refer to the following.

User's manual for the master/local module used

RELEVANT MANUALS

(1) CC-Link IE Field Network (relevant) manuals

When using the CC-Link IE Field Network for the first time, refer to the CC-Link IE Field Network Master/Local

Module User's Manual or Simple Motion Module Use's Manual first. The following shows the structure of the CC-

Link IE Field Network manuals.

(2) Operating manual

Manual name

[manual number (model code)] Description

MELSEC-Q CC-Link IE Field Network Master/Local Module User's Manual

[SH-080917ENG, 13JZ47]

Overview of the CC-Link IE Field Network, and specifications,

procedures before operation, system configuration, installation, wiring,

settings, functions, programming, and troubleshooting of the QJ71GF11-

MELSEC-L CC-Link IE Field Network Master/Local Module User's Manual

[SH-080972ENG, 13JZ54]

Overview of the CC-Link IE Field Network, and specifications,

procedures before operation, system configuration, installation, wiring,

settings, functions, programming, and troubleshooting of the LJ71GF11-

MELSEC iQ-R Ethernet/CC-Link IE User's Manual (Startup)

[SH-081256ENG, 13JX09]

Specifications, procedures before operation, system configuration,

wiring, and communication examples of Ethernet, CC-Link IE Controller

Network, and CC-Link IE Field Network

MELSEC iQ-R CC-Link IE Field Network User's Manual (Application)

[SH-081259ENG, 13JX18]

Functions, parameter settings, programming, troubleshooting, I/O

signals, and buffer memory of CC-Link IE Field Network

MELSEC iQ-R Inter-Module Synchronization Function Reference Manual

[SH-081401ENG]

Inter-module synchronization function, which controls multiple modules

synchronously

MELSEC-Q QD77GF Simple Motion Module User's Manual (Network)

[IB-0300203, 1XB957]

Functions, programming, and troubleshooting of CC-Link IE Field

Network for the QD77GF16

MELSEC-Q QD77GF Simple Motion Module User's Manual (Positioning Control)

[IB-0300202, 1XB956]

Specifications of the QD77GF16, information on how to establish a

system, maintenance and inspection, and troubleshooting.

Also included are functions, programming, and buffer memory for the

positioning control of the QD77GF16.

CC-Link IE Field Network Remote I/O Module User's Manual

[SH-081114ENG, 13JZ82]

Specifications, procedures before operation, system configuration,

installation, wiring, various settings, functions, programming, and

troubleshooting of the CC-Link IE Field Network remote I/O module

CC-Link IE Field Network Analog-Digital Converter Module User's Manual

[SH-081451ENG, 13JX26]

Specifications, procedures before operation, system configuration,

installation, wiring, various settings, functions, programming, and

troubleshooting of the CC-Link IE Field Network analog-digital converter

module

Manual name

[manual number (model code)] Description

GX Works2 Version 1 Operating Manual

(Common)

[SH-080779ENG, 13JU63]

System configuration, parameter settings, and online operations of GX

Works2, which are common to Simple projects and Structured projects

GX Works3 Operating Manual

[SH-081215ENG]

System configuration, parameter settings, and online operations of GX

Works3

CONTENTS

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

CONDITIONS OF USE FOR THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

RELEVANT MANUALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

MANUAL PAGE ORGANIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PACKING LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CHAPTER 1 D/A CONVERTER MODULE 15

1.1 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

CHAPTER 2 PART NAMES 19

2.1 Main D/A Converter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.2 Extension D/A Converter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

CHAPTER 3 SPECIFICATIONS 23

3.1 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.2 Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.2.1 Main D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3.2.2 Extension D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

3.3 How to Calculate Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3.4 Function List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.5 List of Remote I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.5.1 Main D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

3.5.2 Extension D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

3.6 List of Remote Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3.6.1 Main D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

3.6.2 Extension D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

3.7 List of Remote Buffer Memory Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

3.7.1 Main D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

3.7.2 Extension D/A converter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

CHAPTER 4 PROCEDURES BEFORE OPERATION 45

CHAPTER 5 SYSTEM CONFIGURATION 47

5.1 System Configuration with D/A Converter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

5.2 Applicable Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

CHAPTER 6 INSTALLATION AND WIRING 49

6.1 Station Number Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

6.2 Installation Environment and Installation Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

6.2.1 Installation environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

6.2.2 Installation position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Mitsubishi Electric Controllori

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric EW-50A Guida rapida

Mitsubishi Electric

Mitsubishi Electric Q Series Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric MELDAS MDS-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX3U-232-BD Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX3U-4AD-TC-ADP Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R C Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric QA1S6ADP-S1-U-E Manuale utente

Mitsubishi Electric

Mitsubishi Electric Melsec iQ-R60AD8-G Manuale utente

Mitsubishi Electric

Mitsubishi Electric EZMOTION MR-E Super MR-E-10A-QW003 Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MR-J5W-G Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric PAC-IF033B-E Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX6U Istruzioni per l’uso

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAC-AH001-1 Manuale utente

Mitsubishi Electric

Mitsubishi Electric NZ2GF2S-60IOLD8 Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC-QS Series Guida utente

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente