Mitsubishi Electric Q66DA-G Manuale utente

Channel Isolated Digital-Analog Converter Module

User's Manual

-Q66DA-G

-GX Configurator-DA (SW2D5C-QDAU-E)

A- 1

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full attention

to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of the

programmable controller system, refer to the user's manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

Do not write any data to the "system area" of the buffer memory in the intelligent function module.

Also, do not use any "use prohibited" signals as an output signal from the programmable controller

CPU to the intelligent function module.

Doing so may cause malfunction of the programmable controller system.

CAUTION

Do not install the control lines or communication cables together with the main circuit lines or power

cables.

Keep a distance of 100mm (3.9 inches) or more between them. Failure to do so may result in

malfunction due to noise.

At power-on, a voltage may occur or a current may flow between output terminals for a moment.

In this case, start the control after analog outputs become stable.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

A- 2

[Installation Precautions]

[Wiring Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications in the

user's manual for the CPU module used.

Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of the

product.

To mount the module, while pressing the module mounting lever located in the lower part of the

module, fully insert the module fixing projection(s) into the hole(s) in the base until it snaps into

place.

Incorrect mounting may cause malfunction, failure or drop of the module.

Fix the module to the base unit with a fixing bracket.

Tighten the screw within the specified torque range.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.

Shut off the external power supply (all phases) used in the system before mounting or removing the

module.

Failure to do so may result in damage to the product.

A module can be replaced online (while power is on) on any MELSECNET/H remote I/O station or in

the system where a CPU module supporting the online module change function is used.

Note that there are restrictions on the modules that can be replaced online, and each module has its

predetermined replacement procedure.

For details, refer to the relevant chapter in this manual.

Do not directly touch any conductive parts and electronic components of the module.

Doing so can cause malfunction or failure of the module.

CAUTION

Individually ground the FG terminal of the programmable controller with a ground resistance of 100Ω

or less.

Failure to do so may result in electric shock or malfunction.

Tighten the terminal screw within the specified torque range.

Undertightening can cause short circuit, fire, or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.

Prevent foreign matter such as dust or wire chips from entering the module.

Such foreign matter can cause a fire, failure, or malfunction.

A- 3

[Wiring Precautions]

[Startup and Maintenance Precautions]

CAUTION

A protective film is attached to the top of the module to prevent foreign matter, such as wire chips,

from entering the module during wiring.

Do not remove the film during wiring.

Remove it for heat dissipation before system operation.

WARNING

Do not touch any terminal while power is on.

Doing so will cause electric shock or malfunction.

Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal screws, connector screws, or module fixing screws.

Failure to do so may result in electric shock or cause the module to fail or malfunction.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.

CAUTION

Do not disassemble or modify the modules.

Doing so may cause failure, malfunction, injury, or a fire.

Shut off the external power supply (all phases) used in the system before mounting or removing the

module.

Failure to do so may cause the module to fail or malfunction.

A module can be replaced online (while power is on) on any MELSECNET/H remote I/O station or in

the system where a CPU module supporting the online module change function is used.

Note that there are restrictions on the modules that can be replaced online, and each module has its

predetermined replacement procedure.

For details, refer to the relevant chapter in this manual.

After the first use of the product, do not mount/remove the module to/from the base unit more than

50 times (IEC 61131-2 compliant).

Exceeding the limit of 50 times may cause malfunction.

Before handling the module, touch a grounded metal object to discharge the static electricity from

the human body.

Failure to do so may cause the module to fail or malfunction.

A- 4

[Disposal Precautions]

CAUTION

When disposing of this product, treat it as industrial waste.

A- 5

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major

or serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of

the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT

LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,

WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR

LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR

USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,

OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY

MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any

other cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of

a special quality assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as

Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,

Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or

Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a

significant risk of injury to the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT

is limited only for the specific applications agreed to by Mitsubishi and provided further that no

special quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A- 6

REVISIONS

* The manual number is given on the bottom left of the back cover.

Print Date *Manual Number Revision

Oct., 2006 SH (NA)-080648ENG-A First edition

Jan.,2007 SH (NA)-080648ENG-B

Section 3.2.1, 4.6

Jan., 2008 SH (NA)-080648ENG-C

SAFETY PRECAUTIONS, About the Generic Terms and Abbreviations,

Section 1.1, 2.1, 2.3, 4.1, 4.6, 5.2.1, 5.2.2, 7.3.3, 7.3.5, 8.1, Appendix 1, 1.1 to

1.3

Section 2.2

May, 2008 SH (NA)-080648ENG-D

SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage

Directives, About the Generic Terms and Abbreviations, Section 2.1, 2.3, 4.1,

4.3, 5.1, 5.2.1, 5.2.2, 5.3.1, 5.3.3, Chapter 7, Section 7.1

Nov., 2010 SH (NA)-080648ENG-E

SAFETY PRECAUTIONS, RELATED MANUALS, ABOUT THE GENERIC

TERMS AND ABBREVIATIONS, PRODUCT STRUCTURE, Section 1.1, 2.1 to

2.3, 3.1.1, 3.1.2, 3.2, 3.2.1, 3.2.3, 3.2.5, 3.3.1, 3.3.2, 3.4.1, 3.4.3, 3.4.4, 3.4.6,

4.1, 4.3, 4.4.2, 4.5, 4.6, 5.1, 5.2.1, 5.2.2, 5.3.1, 5.3.3, 5.4, 5.5, 5.6.1, 5.6.2, 5.7,

6.2.3, 6.3, 6.3.1, 6.3.2, 7.1, 7.2, 7.3.1 to 7.3.6, 7.4, 7.5, 8.1, 8.2.4, 8.2.6, 8.2.7,

Appendix 1, 1.1 to 1.3

CONDITIONS OF USE FOR THE PRODUCT, Appendix 2

Feb., 2012 SH (NA)-080648ENG-F

SAFETY PRECAUTIONS, COMPLIANCE WITH EMC AND LOW VOLTAGE

DIRECTIVES, GENERIC TERMS AND ABBREVIATIONS, Section 3.1.1, 3.1.2,

3.2.2, 4.1, 4.3, 4.4.2, 5.2.2, 5.4, 5.5, 6.2.2, 6.2.3, 6.3, Chapter 7, Section 7.1,

7.3.4

Dec., 2012 SH (NA)-080648ENG-G

MANUALS, COMPLIANCE WITH EMC AND LOW VOLTAGE DIRECTIVES,

Section 2.1, 2.2, 3.2.2, 3.2.4, 3.3.2, 3.4.2, 4.2, 4.3, 4.4.2, 4.5, 4.6, 5.2, 5.2.1,

5.2.2, 6.2.1, 8.1, 8.2.1, 8.2.4, 8.2.7, Appendix 1.1 to Appendix 1.3

May., 2015 SH (NA)-080648ENG-H

GENERIC TERMS AND ABBREVIATIONS, Section 2.1, 2.3, 4.3, 4.6,

Appendix 3

Correction

Addition

Correction

Addition

Correction

A- 7

Japanese Manual Version SH-080646-K

Jul., 2017 SH (NA)-080648ENG-I

INTRODUCTION, COMPLIANCE WITH EMC AND LOW VOLTAGE

DIRECTIVES, GENERIC TERMS AND ABBREVIATIONS, 4.4.2, 4.5

Section 4.4.3, 8.2.7

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial

property rights which may occur as a result of using the contents noted in this manual.

Print Date *Manual Number Revision

Correction

Addition

A- 8

SAFETY PRECAUTIONS .................................................................................................................................A - 1

CONDITIONS OF USE FOR THE PRODUCT..................................................................................................A - 5

REVISIONS.......................................................................................................................................................A - 6

INTRODUCTION...............................................................................................................................................A - 8

CONTENTS ......................................................................................................................................................A - 8

MANUALS.......................................................................................................................................................A - 12

RELEVANT MANUALS...................................................................................................................................A - 12

COMPLIANCE WITH EMC AND LOW VOLTAGE DIRECTIVES...................................................................A - 12

GENERIC TERMS AND ABBREVIATIONS....................................................................................................A - 13

PACKING LIST ...............................................................................................................................................A - 13

1 OVERVIEW 1 - 1 to 1 - 2

1.1 Features........................................................................................................................................... 1 - 1

2 SYSTEM CONFIGURATION 2 - 1 to 2 - 6

2.1 Applicable Systems ......................................................................................................................... 2 - 1

2.2 Precautions on System Configuration ............................................................................................. 2 - 3

2.3 Checking Function Version, Serial Number and Software Version ................................................. 2 - 4

3 SPECIFICATIONS 3 - 1 to 3 - 36

3.1 Performance Specifications ............................................................................................................. 3 - 1

3.1.1 Performance specifications list ............................................................................................... 3 - 1

3.1.2 I/O conversion characteristics ................................................................................................ 3 - 2

3.1.3 Accuracy................................................................................................................................. 3 - 7

3.1.4 Conversion speed................................................................................................................... 3 - 7

3.2 Function List .................................................................................................................................... 3 - 8

3.2.1 Analog output HOLD/CLEAR function.................................................................................... 3 - 9

3.2.2 Analog output test during programmable controller CPU STOP .......................................... 3 - 11

3.2.3 Warning output function........................................................................................................ 3 - 12

3.2.4 Rate control function............................................................................................................. 3 - 14

3.2.5 Scaling function .................................................................................................................... 3 - 16

3.3 I/O Signals for the Programmable Controller CPU ........................................................................ 3 - 19

3.3.1 List of I/O signals .................................................................................................................. 3 - 19

3.3.2 Details of I/O signals............................................................................................................. 3 - 20

INTRODUCTION

Thank you for purchasing the Mitsubishi Electric MELSEC-Q series programmable controllers.

Before using the equipment, please read this manual carefully to develop full familiarity with the functions

and performance of the Q series programmable controller you have purchased, so as to ensure

correct use.

Please forward a copy of this manual to the end user.

CONTENTS

Altri manuali per Q66DA-G

Indice

Altri manuali Mitsubishi Electric Controllori

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R RD78G4 Manuale utente

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAC-AH001-1 Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX3U-CAN Manuale utente

Mitsubishi Electric

Mitsubishi Electric Artisan MELSEC-Q Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRB Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Manuale utente

Mitsubishi Electric

Mitsubishi Electric CR750-D Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX2N-32ASI-M Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric NZ2GN2S1-16D Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC FX Series Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric NZ2MFB2-16A Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX3G SERIES Manuale di istruzioni

Mitsubishi Electric

Mitsubishi Electric ANS-Q-LARGE-U Manuale utente

Mitsubishi Electric

Mitsubishi Electric FX3U-USB-BD Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC L series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R C Manuale del proprietario

Mitsubishi Electric

Mitsubishi Electric LCPU-U-HW Manuale di istruzioni

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric LE-40MT Series Manuale utente

Mitsubishi Electric

Mitsubishi Electric MELDAS C6 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente