Mitsubishi FX-10P-E Manuale di installazione

OPERATION MANUAL

FX-10P-E

This manual explains the programming and monitoring

procedures of the micro PC MELSEC-FX series using the

FX-10P-E handy programming panel.

Read this manual carefully and thoroughly and make sure

the specifications for handy programming panel are correct.

See the corresponding FX series PC manual for details

about PC handing and instructions.

CONTENTS

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P1

2. Sample program operation . . . . . . . . . . . . . . . . . . P11

3. Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P21

4. Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P56

5. Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P65

6. Other functions . . . . . . . . . . . . . . . . . . . . . . . . . . . P75

7. Detailed procedure for starting up the system. . . . P89

8. Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P96

FX-10P-E Handy programming panel

Guidelines for the Safety of the User and Protection of the FX-10P-E HANDY

PROGRAMMING PANEL.

This manual provides information for the use of the FX-10P-E HANDY PROGRAMMING

PANEL. The manual has been written to be used by trained and competent personnel. The

definition of such a person or persons is as follows:

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual, should be of a competent

nature, trained and qualified to the local and national standards required to fulfill that

role. These engineers should be fully aware of all aspects of safety with regards to

automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for said product. All

maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed equipment (See Note) should be trained to use this

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is connected with the actual operation

of the completed equipment.

Note : The term ‘completed equipment’ refers to a third party constructed device which

contains or uses the product associated with this manual.

FX-10P-E Handy programming panel

Note’s on the Symbols Used in this Manual

At various times through out this manual certain symbols will be used to highlight points which

are intended to ensure the users personal safety and protect the integrity of equipment.

Whenever any of the following symbols are encountered its associated note must be read and

understood. Each of the symbols used will now be listed with a brief description of its meaning.

Hardware Warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property

damage.

3) Indicates a point of further interest or further explanation.

Software Warnings

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should

be aware.

6) Indicates a point of interest or further explanation.

FX-10P-E Handy programming panel

iii

• Under no circumstances will Mitsubishi Electric be liable responsible for any consequential

damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. Mitsubishi Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

• Please contact a Mitsubishi distributor for more information concerning applications in life

critical situations or high reliability.

FX-10P-E Handy programming panel

Caution on operation

Thoroughly read the manual and sufficiently assure safety before executing the operation to

forcibly set devices to ON/OFF or the operation to change present values and set values of

word devices in the test mode.

Otherwise, the machine may be damaged and accidents may occur by erroneous operations.

Version upgrade to support FX1S, FX1N, FX2N and FX2NC Series Programmable controllers.

(ver 4.10 or later)

The FX-10P-E (ver 4.10 or later) fully supports all items and procedures used for the FX1S,

FX1N, FX2N and FX2NC PLCs.

Read section 1-3 in addition to the contents of the text when using the FX-10P-E (ver 4.10 or

later).

1. New Features

!: Already compatible ✕: Not yet compatible

Table 1.1

New Feature Supported by Peripheral

1 Addition of FX2N, FX1N, FX1S as selectable model !

2 Addition of basic and applied instructions !described in section 2 below

3 Expansion of device range !described in section 2 below

4Addition of 16K-step program memory !parameter setting

Setting of external RUN input !parameter setting

5 Writing of EPROM cassette ✕

6 Remote RUN/STOP function ✕

7 Specification of batteryless operation mode ✕

8 Setting communication Parameters ✕

9 Specification of modem initialization ✕

2. List of Additional Devices and Instructions

• For details of each instruction and devices, refer to the FX programming manual.

Table 2.1 Table 2.2

Devices Basic Instructions

Auxiliary relays M0 to M3071 3072 points LDP ORP

Data registers D0 to D7999 8000 points LDF ORF

Index registers V0 to V7, Z0 to Z7 16 points ANDP INV

ANDF

Table 2.3

Applied Instructions Applied Instructions Applied Instructions Applied Instructions

FNC No. Instruction FNC No. Instruction FNC No. Instruction FNC No. Instruction

59 PLSR 127 ESQR 158 DRVI 170 GRY

110 ECMP 129 INT 159 DRVA 171 GBIN

111 EZCP 130 SIN 160 TCMP 176 RD3A

118 EBCD 131 COS 161 TZCP 177 WR3A

119 EBIN 132 TAN 162 TADD 180 EXTR

120 EADD 147 SWAP 163 TSUB 224 to

246

In line

Compare

121 ESUB 155 DABS 166 TRD

122 EMUL 156 ZRN 167 TWR

123 EDIV 157 PLSV 169 HOUR

vii

3. New Operations for FX2N, FX2NC, FX1N, FX1S Support

3.1 Basic and Applied instructions are added

Symbol and input operation of additional basic instructions

Table 3.1

Instruction Description Mnemonic Key Operations

LDP Initial leading edge pulse contact LDP

LDF Initial trailing edge pulse contact LDF

ANDP Serial connection leading edge

pulse contact ANP

ANDF Serial connection trailing edge

pulse contact ANF

ORP Parallel connection leading edge

pulse contact ORP

ORF Parallel connection trailing edge

pulse contact ORF

INV Invert current logical status INV

LD P/I Device Number GO

LD FDevice Number GO

AND P/I Device Number GO

AND FDevice Number GO

OR P/I Device Number GO

OR FDevice Number GO

NOP P/I GO

viii

Applied instruction input operation

• It is the responsibility of the operator to ensure that the instruction entered is valid for the

current unit.

Application instruction input operation (by using the HELP function)

• When using the HELP function with a model other than FX2N be careful not to select an

invalid instruction.

FNC SPApplied Instruction No. Operand 1 SP Operand 2 GO

.....

The number of operands vary

depending on the instruction.

Example :

0 1

0 PROGRAM FLOW

1 TRANSFERS, COMP

10 CMP 12 MOV

11 ZCP 14 CML

Indice

Altri manuali Mitsubishi Controllori

Mitsubishi

Mitsubishi MELSEC QS Series Manuale utente

Mitsubishi

Mitsubishi FX2NC Series Manuale utente

Mitsubishi

Mitsubishi alpha 2 Manuale utente

Mitsubishi

Mitsubishi FX2NC DSS Series Manuale utente

Mitsubishi

Mitsubishi MELSEC-A AJ71E71-S3 Manuale utente

Mitsubishi

Mitsubishi Q00JCPU Manuale utente

Mitsubishi

Mitsubishi Q64TD Manuale utente

Mitsubishi

Mitsubishi FX3U-20SSC-H Manuale utente

Mitsubishi

Mitsubishi AL2-2PT-ADP Manuale utente

Mitsubishi

Mitsubishi Alpha Series Manuale del proprietario

Mitsubishi

Mitsubishi AD71S1 Manuale utente

Mitsubishi

Mitsubishi MELSEC A1SCPU Istruzioni per il montaggio

Mitsubishi

Mitsubishi FX-2AD-PT Manuale utente

Mitsubishi

Mitsubishi NZ2GFCF-D62PD2 Manuale utente

Mitsubishi

Mitsubishi MELSEC-AnS Series Manuale utente

Mitsubishi

Mitsubishi MELSEC iQ-F FX5-4AD-TC-ADP Manuale utente

Mitsubishi

Mitsubishi MELSEC Manuale utente

Mitsubishi

Mitsubishi FX2N-485-BD Manuale utente

Mitsubishi

Mitsubishi FREQROL-SFJ Manuale utente

Mitsubishi

Mitsubishi Q172CPU Manuale utente

Mitsubishi

Mitsubishi FX2N-4AD-PT Manuale utente

Mitsubishi

Mitsubishi FX3U Series Manuale utente

Mitsubishi

Mitsubishi FX2N Manuale utente

Mitsubishi

Mitsubishi FX3U-4LC Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente