MJX HYPER GO 16207 Manuale utente
No.16207 14+
1:16 RC HIGHSPEED CAR
USER MANUAL
!
Safety Precautions
In order to operate the car safely. Be sure that you have observed
the following points:
●It is a radio control model, not a toy!
●In order to enjoy running the car, you need to finish assembly before operation. Do routine maintenance
work after operation. Replacement parts and option parts are available separately.
●Improper usage with Alkaline cells or rechargeable batteries may damage the electronics for the car or
the radio.
Please follow the points as below in order to prevent accident from happening to the car and
people.
Precautions for Battery Use
1. Transmitter uses 2x1.5V “AA” batteries.
2. Please pay attention to correct polarity when replacing batteries.
3. Rechargeable batteries should be charged under adult supervision.
4. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable
batteries.
5. After the battery is exhausted, the model should be removed.
6. Exhaust battery should be safety dispose!
7. DO NOT short circuit any terminals.
8. DO NOT attempt to recharge non rechargeable batteries.
9. Remove batteries from the model when charging.
10. DO NOT put batteries into a fire or into water.
11. The rated input voltage battery charger MUST be suitable for your mains power voltage.
12. During charging it is quite normal for the charger and batteries to heat up.
13. Do not swallow battery!
14. Store only in cool, dry and dark places and should be keep out of the children!
15. When the battery leaks the liquid and let it into you eyes, please right away rinse them and consult
an ophthalmologist.
The instruction sheet for this product is just for your reference. We reserve the right to make changes
or adjustments on the product without prior notification. Please refer to the official information.
Warning:
Choking hazard! This product contains small parts. NOT suitable for children under 3 years. Contains
electrical components and should be kept dry at all times. Regularly check the battery charger wires,
plugs and shell and other components for damage. DO NOT use if any part is damaged.
Warnings & Cautions
1. Detachable small parts should be stored safely and out of reach of children.
2. If interference is experienced, turn the model off and try it again in a different area.
3. Transmitter will not function correctly if the batteries are low. Please replace the batteries.
4. Please discard old/used batteries in a safe manner. Consider your environment!
5. Please store the remote control model in cool, dry place.
6. DO NOT expose to fire or high temperatures, do not store in moist place.
7. Once the battery get wet, wipe immediately with a soft dry cloth.
If the battery any deformation, please stop using.
8. If you don’t use the model for a long time, please raise the chassis to let the wheels hang in the air.
-1-
!Do NOT operate the model in the following places and situations.
(Non-observance may lead to accident!)
Operating Your Model Safely
●Operate your model in spacious and safe areas! Do not operate it:
1. On road!
2. In places where children and many people gather.
3. In residential districts and parks!
4. Do not operate the model on public roads, in crowded places and near infant as it may cause
accidents.
5. Indoors and in limited space! Non-observance may result in personal injury and property damage!
●The car must stop immediately and check for the reasons when it is operating abnormal.
As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and
unforeseen accidents!
●Always check the radio batteries!
With weak dry batteries, transmission and reception of the radio would fall off. You may lose control
of your model in such condition. This may also cause serious accidents!
●Keep in mind that people around you may also operate a radio control model!
NEVER share the same frequency with somebody else at the same time! Otherwise, Radio signals
will be mixed up and you will lose control to your model. This may lead to accidents.
●Do NOT put fingers or any objects inside rotating and moving parts!
●Right after use, do NOT touch the motor! Danger of burning yourself!
●When the model is not in use, always turn off the receiver and transmitter. Further more, disconnect
the batteries and remove them from the model and the transmitter. This may be dangerous such as
overheat and leakage.
●Be sure to read thoroughly
the manual before you
begin. Fresh user should
seek advice from people
having rich experience in
order to assemble the
model correctly.
●Cutters, nippers and
screwdrivers need careful
handling.
●Do not expose this model
to high temperature, humidity
or direct sunlight.
●Never reverse connection/
disassemble the battery.
This may lead to damage
and leakage.
●As the product contains
small and sharp parts,
assemble and store this
product only in places
out of the reach of children.
-2-
FCC PART 15 B Notice:
CAUTION
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
-3-
Power Switch
1. Turn on the power switch of the transmitter, the signal indicator light of transmitter flashes.
2. Press the power button of high speed car, which is on the side of the ESC; the indicator light of high
speed car flashes.
3. When the indicator light stays on, the high speed car can be operated to play.
!●When turn on the transmitter, please DO NOT touch the throttle and steering. After turn on the
transmitter’s power, please operate after the indicator light of transmitter staying on.
●Please comply the principle of “turn on the transmitter firstly, then turn on the high speed car’’.
●In the frequency matching, please make sure there is only one pair of transmitter and high speed
car in matching at the same time, otherwise the frequency will match wrongly.
R30 Receiver
!Warning: Please make sure the connection is correct.
VCC/FAN
VCC/FAN
CH3
CH2
CH1
VCC/FAN
VCC/FAN
CH3
CH2
CH1
Antenna
(Please make sure it in
vertical direction)
Stays on Signaled
R30 Indicator
situation Meanings
Flashes No Signal
VCC/FAN: Power Interface (VCC=5-6V)
ESC
(CH2)
Steering
servo
(CH1)
Fan
(VCC/FAN)
R30
-4-
T3B Transmitter
①ST.TRIM
(Steering servo strimmer)
②TH.TRIM (Throttle trimmer)
③Power switch
(OFF-70%TH-100%TH)
④Indicator light
⑤ CH1: ST (Steering)
⑥ CH2: TH (Throttle)
⑦CH3: Fn
If the car cannot go straightly during driving, it can
be adjusted through the ST.TRIM.
①ST.TRIM (Steering servo strimmer)
!Please Do Not forcible/reversely insert all sockets.
E45A Brushless ESC
Stays on Signaled
E45A Indicator
light situation Meanings
Flash quickly a. No signal
b. Pull the trigger
Flash slowly Low voltage
Flash twice Over heat
protection
Off Stuck protection
Indicator
VCC/BVD
Yellow wire A
Blue wire C
White wire B
Power switch
Heat sink
VCC: Powered by battery circuit. Please provide the same voltage as the connected battery. It can be used
as cooling fan power power. Please make sure the battery voltage of the ESC is in the range of fan’s.
BVD: Receivers with BVD function can be directly connected to this interface through an adapter cable, which
is equivalent to connecting a battery.
If the car can’t be stop when the TH in the
middle place, you can adjust the button to
stop the car.
②TH.TRIM (Throttle trimmer)
Forward
-5-
70%
(70% Throttle)
OFF 100%
(100% Throttle)
Flash quickly Frequency mating
Stays on Working well
Flash slowly Low battery of transmitter
③Power/Speed switch ④Indicator light
⑤CH1: ST (Steering)
Middle Turn left Turn right
⑥CH2: TH (Throttle)
Forward
Brake: When the car is going forward, pull the transmitter trigger back,
and the car enters into the braking state. After the trigger is in the
middle, push back again, and the car can move backward.
*When the car is in reverse situation, it does not the brake function.
Backward
Middle
Push
forward
Pull
back
Pull
back
-6-
Install the Head Wheels
Fix the head wheels into
the rear of the car via 3
screws.
Install the tail to the body, lock with 2 screws.
Install the Tail
Install the Transmitter’s Battery
Open the transmitter’s battery cover, insert 2 AA batteries according to the indicated positive and
negative direction, close the battery cover.
-7-
Adapter 5V2A
(Sold separately)
Install Battery and Charge Battery
①Turn the battery lock knob and flip up the cover;
②Connect the receiver plug to the battery;
③Put the battery into the battery holder and make sure it is in place;
④Flip back the cover and turn the knob to lock it.
Install the battery
High speed car battery: 11.1V 1050mAh 25C.
If charging with a 5V 2A USB adapter, the charging time is about 240 minutes.
●When charging, the indicator light of charger is green and flashes;
●When the battery is fully charged, the green indicator light of the charger stays on.
*The above charging time data is based on the test result of 5V 2A adapter. Using different specifications
of adapters or power supply equipment will affect the actual charging time. It is recommended to use a
5V2A adapter for charging.
Charge
-8-
Install Car Shell
1. Aline the 3 holes of the car shell with holders, then install it.
2. Insert the 3 clips into the holes to lock the car body.
-9-
Indice
Altri manuali MJX Auto giocattolo motorizzata
