MK Diamond Products 166110 Guida all'applicazione

MK DIAMOND

TRACK RAIL SAW

OPERATION & PARTS MANUAL

www.mkdiamond.com

Caution: Read all safety and operating instructions

before using this equipment. This manual MUST

accompany the equipment at all times.

03.2012Revision 302

Manual Part No. 166110

TRACK RAIL SAW INTRODUCTION

Congratulations on your purchase of a Track Rail Saw. We are certain that you will be pleased with

your purchase. MK Diamond takes pride in producing the nest construction power tools and dia-

mond blades in the industry.

Operated correctly, your Track Rail Saw should provide you with years of service. In order to help

you, we have included this manual. This owners manual contains information necessary to operate

and maintain your Track Rail Saw safely and correctly. Please take the time to familiarize yourself

with the Track Rail Saw by reading and reviewing this manual.

Read and follow all safety, operating and maintenance instructions.

If you should have questions concerning your Track Rail Saw, please feel free to call our friendly cus-

tomer service department at: 800 421-5830

Regards,

MK Diamond

NOTE THIS INFORMATION FOR FUTURE USE:

MODEL NUMBER:

SERIAL NUMBER:

PURCHASE PLACE:

PURCHASE DATE:

NOTE: For your (1) one year warranty to be effective, complete the warranty card

(including the Serial Number) and mail it in as soon as possible.

MK DIAMOND TRACK RAIL SAW

SAFETY

Safety Message/Alert Symbols

Safety Warnings

Hazard Symbols

Electric Motor Safety

Rules for Safe Operation

Operation & Safety Decals

PRODUCT SPECIFICATIONS

Specications

SET-UP

Rail Assembly

Rail Assembly Connector

Cutting Head Assembly

Material Clamps & Alignment

Hose Set-Up

OPERATION

Plunge Cutting for a 90º Cut

Plunge Cutting for a Miter Cut

MAINTENANCE

Blade Replacement

Filter Replacement

Roller Wheel Replacement

GENERAL PRODUCT INFORMATION

Parts List: Final Assembly

Parts List: Main Carrier Assembly

Parts List: Cutting Head Assembly

Parts List: Blade Guard Assembly

Parts List: Parallel Rail Support Bracket

Parts List: Rail Connector Plate

Parts List: Rail Saw Material Clamp

Ordering Information

Contact Information and Limited Warranty

PAGE NO.

8-9

21-23

24-25

26-27

28-29

TRACK RAIL SAW TABLE OF CONTENTS

TRACK RAIL SAW SAFETY

Safety precautions should be followed at all times when operating this equipment. Failure to read and

understand the Safety Precaution and Operating Instructions could result in injury to yourself and

others.

This Operation Manual has been developed to provide complete instructions for the safe and efcient

operation of the CX-3®Concrete Saw.

SAFETY MESSAGE / ALERT SYMBOLS

A safety message alerts you to potential hazards that could hurt you or others. Each safety message is

preceded by a safety alert symbol ( ) and one of three words: DANGER, WARNING, or CAUTION.

DANGER

You WILL be KILLED or SERIOUSLY INJURED if you do not follow directions.

WARNING

You CAN be KILLED or SERIOUSLY INJURED if you do not follow directions.

CAUTION

You CAN be INJURED if you do not follow directions. It may also be used

to alert against unsafe practices.

NOTICE

You can cause PROPERTY DAMAGE to your machine if you don’t follow directions.

Each message tells you what the hazard is, what can happen, and what you can do to avoid or

reduce injury. Other important messages are preceded by the word NOTICE.

The safety labels should be periodically inspected and cleaned by the user to maintain good legibility

at a safe viewing distance. If the label is worn, damaged or illegible, it should be replaced. Contact

MK Diamond or your dealer for replacement.

Before using this saw, ensure that the person operating the equipment has read and understands all

instructions in this manual.

DAMAGE PREVENTION AND INFORMATION MESSAGES

A Damage Prevention Message is to inform the user of important information and/or instructions that

could lead to equipment or other property damage if not followed. Information messages convey

information that pertains to the equipment being used. Each message will be preceded by the word

note, as in the example below.

NOTE: Equipment and/or property damage may result if these instructions are not followed.

TRACK RAIL SAW SAFETY

CALIFORNIA PROPOSITION 65 MESSAGE

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities con-

tain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

•Lead, from lead-based paints

•Crystalline silica, from bricks and cement and other masonry products

•Arsenic and chromium, from chemically treated lumber

For further information, consult the following sources:

http://www.osha.gov/dsg/topics/silicacrystalline/index.html

http://www.cdc.gov/niosh/consilic.html

http://oehha.ca.gov/prop65/law/P65law72003.html

http://www.dir.ca.gov/Title8/sub4.html

Your risk from these exposures varies depending on how often you do this type of work. To reduce

your exposure to these chemicals, work in a well-ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to lter out microscopic particles.

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition

may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz,

brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of

airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In ad-

dition, California and some other authorities have listed respirable crystalline silica as a substance

known to cause cancer. When cutting such materials, always follow respiratory precautions.

SILICA DUST WARNING

Potential hazards associated with the MK Diamond Track Rail Saw will be referenced with Hazard

Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Mes-

sage Alert Symbols.

ALWAYS wear a hard hat.

ALWAYS wear approved eye protection.

HAZARD SYMBOLS

ALWAYS wear approved ear protection.

ALWAYS wear approved respiratory protection.

ALWAYS read this Owner’s Manual before operating the machine.

ALWAYS avoid inhalation of and skin contact with silica dust and/or mist.

TRACK RAIL SAW SAFETY

WARNING

DO NOT use woodcutting, or carbide blades on this machine! Use ONLY Diamond blades on ma-

chine. Use machine only to cut tile and masonry products. DO NOT use machine to cut wood or wood

products.

ELECTRIC MOTOR SAFETY

For maintenance care and operation of the electric motor, refer to your electric motor instruction booklet

furnished with the electric motor.

Protect the electric motor from dust as much as possible and keep ventilating openings clean.

Electric Motor Connection

The table below shows the matching NEMA approved connector for the required extension cord.

ALWAYS make certain that the power source required for the electric motor is correct and always use

the correct NEMA conguration plug. Failure to supply the correct voltage to the motor can severely

damage the motor. Make certain that the correct size grounded (3-wires) extension cord is used. See

the table below.

Motors can burn out when the line voltage falls 10% below the voltage rating of the motor. Failure to

use proper voltage will cause the motor to overheat.

•

DO NOT spray water at any time on the electric motor.

DO NOT operate electric motor in an explosive environment.

CAUTION

NOTICE

Most Motor Problems are caused by improper

voltage and extension cords. Cord should be

one-piece and short as possible. Cord

selection should match the following table.

1-2 H.P.

25’

50’

75’

100’

150’

250’

Max. Cord Length

No. 12 Wire

No. 10 Wire

No. 8 Wire

115v 230v

TRACK RAIL SAW SAFETY

•This equipment should not be operated by persons under 18 years of age.

• NEVER operate this equipment without proper protective clothing, shatterproof glasses, steeltoed

boots and other protective devices required by the job.

• NEVER operate this equipment when not feeling well due to fatigue, illness or taking medicine.

• NEVER operate this equipment under the inuence of drugs or alcohol.

• Whenever necessary, replace nameplate, operation and safety decals when they become difcult

to read.

• ALWAYS check the machine for loose bolts before starting.

•ALWAYS wear proper respiratory (mask) hearing and eye protection

equipment when operating this machine.

• ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean,

dry location out of the reach of children.

 •NEVER leave the machine unattended. Turn off electric motor when unattended.

• CAUTION must be observed while servicing the machine. Rotating parts can cause injury if contacted.

•Ensure that any electrical extension cord is protected against damage. Always ensure that the

electrical extension cord is not trapped underneath the machine. When using an extension cord,

be sure to use one heavy enough to carry the current your product will draw. An undersized cord

will cause a drop in line voltage that will result in a loss of power and overheating. The Table shown

on page 11 shows the correct AWG size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heaviest gage. The smaller the gage number, the heavier the cord.

• Before starting the machine, check that all guards are in position and correctly tted.

•Keep area around the machine clear of obstructions which could cause persons to fall onto moving parts.

• ALWAYS ensure that the machine is on level ground before using.

• DONOT overreach. Keep proper footing and balance at all times.

Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is

to be operated by trained and qualied personnel only! This equipment is for industrial use only.

The following safety guidelines should always be used when operating the MK-2000 Electric Saw.

GENERAL SAFETY

DANGER

RULES FOR SAFE OPERATION

ON / OFF

•DONOT operate or service this equipment before reading this entire manual.

• DONOT allow extension cord to come into contact with water or uids.

•DO NOT spray water onto electric motor.

•NEVER operate the machine in an explosive atmosphere.

TRACK RAIL SAW SAFETY

•NEVER stand on the tool. Serious injury could occur if a power tool is tipped, or if a cutting tool is

unintentionally contacted.

•Become familiar with the controls of the machine before operating. Know how to stop the machine

quickly in case of emergency.

•ALWAYS secure work. Clamps or a vise should be used to hold work whenever practical. Keep-

ing your hands free to operate a power tool is safer.

•ALWAYS disconnect AC power plug from power source before moving, cleaning or servicing the

machine.

•NEVER leave a tool running unattended. Do not leave a tool until it comes to a complete stop.

ALWAYS turn a power tool OFF when leaving the work area, or when a cut is nished.

•Make sure the OFF/ON power switch on the electric motor is always in the OFF position before

inserting the machine’s power plug into an AC receptacle.

•Operate electric motor only at the specied voltage indicated on the nameplate.

•NEVER disconnect any “emergency or safety devices”. These devices are intended for operator

safety. Disconnection of these devices can cause severe injury, bodily harm or even death! Dis-

connection of any of these devices will void all warranties.

•Unauthorized equipment modications will void all warranties. Manufacturer does not assume respon-

sibility for any accident due to equipment modications.

•NEVER use accessories or attachments, which are not recommended by MK Diamond for this

equipment. Damage to the equipment and/or injury to user may result.

• Replace damaged cutting blade before operating.

• NEVER try to stop a moving blade with your hand.

•NEVER lubricate components or attempt service on a running machine.

•Keep the machinery in proper running condition.

•Before using a power tool, check for damaged parts. A guard or any other part that is damage

should be carefully checked to determine if it would operate properly and perform its intended

function. Always check moving parts for proper alignment or binding. Check for broken parts and

mountings and all other conditions that may affect the operation of the power tool. A guard, or any

damaged part, should be properly repaired or replaced.

MAINTENANCE SAFETY

WARNING

NEVER use this machine with any cutter designed for wood working.

•Wear eye protection.

•Disconnect saw before servicing, when changing cutting blades and cleaning.

•Replace damaged cutting blade before operation.

•Remove adjusting keys and wrenches.

SAW SAFETY

WARNING

TRAIL RACK SAW SAFETY

D & F

(behind)

The MK Diamond Track Rail Saw is equipped with a number of safety decals. These decals are pro-

vided for operator safety and maintenance information. The illustration below also shows the location

of these decals. Should any of these operation or safety decals become unreadable, replacements

can be obtained by calling (800) 262-1575.

OPERATION & SAFETY DECALS

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in

their composition may give off dust or mists containing crystalline silica. Silica is a basic

component of sand, quartz, brick clay, granite and numerous other minerals and rocks.

Repeated and/or substantial inhalation of airborne crystalline silica can cause serious

or fatal respiratory diseases, including silicosis. In addition,California and some other

authorities have listed respirable crystalline silica as a substance known to cause cancer.

SERVICE OR

WARRANTY

FOR INFORMATION ON

PLEASE CALL

1-800-474-5594

DO NOT operate

this equipment

before reading

the owners’

manual!

WARNING

CAUTION

DO NOT

operate without

guards in place.

Most Motor Problems are caused by improper

voltage and extension cords. Cord should be

one-piece and short as possible. Cord

selection should match the following table.

1-2 H.P.

25’

50’

75’

100’

150’

250’

Max. Cord Length

No. 12 Wire

No. 10 Wire

No. 8 Wire

115v 230v

NOTICE

This saw is to be used

with a Ground Fault

Circuit Interrupter.

!CAUTION

Decal A Decal B

Decal C

Decal D

Decal E

Decal F

Figure 1. MK Diamond Track Rail Saw Safety Decal Sheet, Part No. 166011

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali MK Diamond Products Sega

MK Diamond Products

MK Diamond Products MK-5005S Manuale del sistema

MK Diamond Products

MK Diamond Products MK-101 Manuale

MK Diamond Products

MK Diamond Products MK-370 Manuale utente

MK Diamond Products

MK Diamond Products CX-3E1 Manuale del sistema

MK Diamond Products

MK Diamond Products MK-101-24 Manuale utente

MK Diamond Products

MK Diamond Products MK-101 Manuale utente

MK Diamond Products

MK Diamond Products MK-101 Manuale utente

MK Diamond Products

MK Diamond Products MK-2000 PRO Series Manuale del sistema

MK Diamond Products

MK Diamond Products MK-3000 Series Manuale utente

MK Diamond Products

MK Diamond Products MK-20 SERIES Manuale utente

MK Diamond Products

MK Diamond Products MK-1280 Manuale utente

MK Diamond Products

MK Diamond Products MK CX-3 Manuale utente

MK Diamond Products

MK Diamond Products 160028 Manuale utente

MK Diamond Products

MK Diamond Products MK-2424HSP Manuale del sistema

MK Diamond Products

MK Diamond Products MK-145 Manuale del sistema

MK Diamond Products

MK Diamond Products MK-101 Manuale utente

MK Diamond Products

MK Diamond Products MK-101 Manuale utente

MK Diamond Products

MK Diamond Products MK-112 Manuale del sistema

MK Diamond Products

MK Diamond Products TX-3 Manuale utente

MK Diamond Products

MK Diamond Products MK-377 Manuale utente

MK Diamond Products

MK Diamond Products MK-145 Manuale del sistema

MK Diamond Products

MK Diamond Products MK-100 TRACKER Manuale del sistema

MK Diamond Products

MK Diamond Products MK-101-24HD Manuale del sistema

MK Diamond Products

MK Diamond Products MK-4018KB Manuale utente

Manuali Sega popolari di altre marche

RIDGID

RIDGID BS1400 Manuale utente

ATIKA

ATIKA BWS 400-2 Manuale utente

RGC

RGC FS20 Manuale utente

Makita

Makita M2300 Manuale utente

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuale utente

IMET Spa

IMET Spa SIRIO 370 AF-E Manuale utente

Optimum

Optimum OPTisaw CS 275 Manuale utente

Makita

Makita BPB180 Manuale utente

Stihl

Stihl MS 462 C-M Manuale utente

AEG

AEG TS 250 K Manuale utente

Meec tools

Meec tools 004665 Manuale utente

Makita

Makita LS1018L Manuale utente

Ryobi

Ryobi RCS1400 Manuale utente

DeWalt

DeWalt DCS391 Manuale utente

Sealey

Sealey SA72 Manuale utente

skilsaw

skilsaw SPT88 Istruzioni per il montaggio

Urrea

Urrea SI810 Dimensioni e guida di installazione

EINHELL

EINHELL BKG 210/1 Manuale utente