ML Accessories BL5BK Manuale di istruzioni
INSTALLATION & MAINTENANCE MANUAL
BL5BK / BL5G / BL5BLBK / BL5BLG
BLKITBK / BLKITG
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
BL5BK / BL5G / BL5BLBK / BL5BLG / BLKITBK / BLKITG
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• This product is Class II double insulated
• This product is IP65 rated
INSTALLATION
Note - If this product is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods). Suitable IP rated junction boxes should be used where required
• Round cable should be used for the mains supply. The use of flat cable may cause water
ingress to the fitting
• Remove the outer frame and the LED gear tray from the luminaire housing (see Fig. 1)
Fig. 1
BL5xx INSTRUCTIONS_SPREADS.indd 5-8BL5xx INSTRUCTIONS_SPREADS.indd 5-8 20/01/2021 16:02:4120/01/2021 16:02:41
SURFACE MOUNTING
• Secure the fitting to the surface with the wall plugs, screws, and rubber washers provided
• Drill two fixing holes in the rear of the luminaire housing, mark the location of the fixing
holes and drill ensuring not to infringe with any gas/water pipes or electrical cables
• Feed the mains cable through the grommet on either the rear or the side of the luminaire
housing (see Fig. 2) ensuring a good seal is made to retain the IP rating. The luminaire
can be fitted horizontally or vertically, enabling cable entry on either side
BL5xx INSTRUCTIONS_SPREADS.indd 5-8BL5xx INSTRUCTIONS_SPREADS.indd 5-8 20/01/2021 16:02:4120/01/2021 16:02:41
Fig. 2
BL5xx INSTRUCTIONS_SPREADS.indd 5-8BL5xx INSTRUCTIONS_SPREADS.indd 5-8 20/01/2021 16:02:4120/01/2021 16:02:41
RECESSED MOUNTING
• For recessed mounting using the BLKITxx, cut a suitable hole in the mounting surface
ensuring not to infringe with any gas/water pipes or electrical cables
• Remove a knockout from the backbox (see Fig. 3)
• Feed the mains cable into the backbox (at this stage there is no requirement for
maintaining the IP rating)
• Fix the backbox securely into the wall flush with the wall surface. Mortar around the
backbox if necessary and allow to set before continuing
• Drill two fixing holes on the rear of the luminaire housing to align with the screw pillars in
the backbox
• Feed the mains cable through one of the cable entry grommets in the luminaire housing
(see Fig. 2) ensuring a good seal is made to retain the IP rating
• Secure the luminaire to the backbox using the M4 screws and rubber washers provided
(see Fig. 4)
Fig. 3
BL5xx INSTRUCTIONS_SPREADS.indd 1-4BL5xx INSTRUCTIONS_SPREADS.indd 1-4 20/01/2021 16:02:4120/01/2021 16:02:41
TERMINATION AND ACCESSORIES
• Connect the luminaire to the mains supply ensuring the correct polarity is observed:
L - Live (brown), N - Neutral (blue)
• Select the desired colour temperature by means of the sliding switch on the LED gear tray
(where applicable)
• Refit the LED gear tray onto the luminaire housing ensuring the cable does not press
against the terminal block which may cause it to open, and secure it with all four screws
ensuring a tight seal is made
• Select a decorative accessory if required, and hold it in place while fitting the appropriate
outer frame – the deep frame should be used if surface mounting; the shallow frame if
recess mounting
• Switch on and check for correct operation
Fig. 4
GENERAL
WARNING
This product contains a light source of energy efficiency class D to Regulation (EU)
No. 2019/2015. (Not applicable to BL5BLxx).
This product contains an LED light source and control gear which can be replaced by a
professional.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please
see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
This product is not suitable for direct installation in the ground, nor in a retaining wall where
the ground may become saturated behind.
DCJUN21_V1
WARRANTY
This product has a warranty of 3 years (BL5xx) / 1 year (BLKITxx) from date of purchase.
Failure to install this product in accordance with the current edition of the IEE Wiring
Regulations (BS7671), improper use, or removal of the batch code will invalidate the
warranty. If this product should fail within its warranty period, it should be returned
to the place of purchase for a free of charge replacement. ML Accessories does not
accept responsibility for any installation costs associated with the replacement product.
Your statutory rights are not affected. ML Accessories reserve the right to alter product
specification without prior notice.
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
02
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali ML Accessories Attrezzatura di illuminazione
ML Accessories
ML Accessories SURF236EMHF Manuale di istruzioni
ML Accessories
ML Accessories 12DCIP40 Manuale di istruzioni
ML Accessories
ML Accessories T8BLED15EM1 Manuale di istruzioni
ML Accessories
ML Accessories AMLEDB Manuale di istruzioni
ML Accessories
ML Accessories CFR5CCT Manuale di istruzioni
ML Accessories
ML Accessories LED3 Series Manuale di istruzioni
ML Accessories
ML Accessories WALL1 Manuale di istruzioni
ML Accessories
ML Accessories 12DC50D Manuale di istruzioni
ML Accessories
ML Accessories SHE1BEM Manuale di istruzioni
ML Accessories
ML Accessories UNDKIT3WWW Manuale di istruzioni
ML Accessories
ML Accessories EMPDL Manuale di istruzioni
ML Accessories
ML Accessories NH027 Manuale di istruzioni
ML Accessories
ML Accessories LFC24B M Series Manuale di istruzioni
ML Accessories
ML Accessories T8BLED12 Manuale di istruzioni
ML Accessories
ML Accessories SPIKEW Manuale di istruzioni
ML Accessories
ML Accessories Knightsbridge SPIKEW Manuale
ML Accessories
ML Accessories WP15CTP Manuale di istruzioni
ML Accessories
ML Accessories Knightsbridge SFPL Series Manuale di istruzioni
ML Accessories
ML Accessories LEDFRA1 Manuale di istruzioni
ML Accessories
ML Accessories FL8ABK Manuale di istruzioni
