Mobotix Mx-SD1A-230-LL Istruzioni operative originali

NOTE!

This guide is only valid for installing and connecting the 2MP Speed Dome Low Light Camera.

For more information on the camera, please refer to the other documents (see Further Reading, p.

8).

Important Installation Notes

nThis camera must be installed by qualified personnel and the installation should conform to

all local codes.

nTo prevent damage, loosen the mounting screws before moving the camera.

nTo ensure that the unit is not affected by vibration, twisting, etc. after adjusting the camera,

tighten all mounting screws properly.

nThis product must not be used in locations exposed to the dangers of explosion.

nInstall this product in a well-ventilated spot and do not close off any vent openings.

nDo not use this product in a dusty environment.

nProtect this product from moisture or water entering the housing.

nInstall this product as outlined in this document. A faulty installation can damage the

product!

nDo not replace batteries of the camera. Risk of explosion may occur if the battery is replaced

by an incorrect type.

nThis equipment is not suitable for use in locations where children are likely to be present.

nExternal power supplies must comply with the LPS requirements and share the same power

specifications with the camera.

nIf using a Class I adapter, the power cord shall be connected to a socket-outlet with proper

ground connection.

nTo comply with the requirements of EN50130-4 regarding the power supply of alarm systems

for 24/7 operation, it is highly recommended to use an uninterruptible power supply (UPS)for

1 / 9

Quick Installation

MOBOTIX 2MP Speed Dome Low Light Camera

Mx-SD1A-230-LL

©2022MOBOTIX AG

Quick Installation 2MP Speed Dome Low Light Camera

powering the product.

nThis equipment is to be connected only to PoE networks without routing to other networks.

NOTE! Observe the MOBOTIX MOVE Installation Hints document to ensure optimum performance

of the camera features.

CAUTION! To prevent damage, loosen all mounting screws before adjusting the camera.

NOTE! To ensure that the unit is not affected by vibration, twisting, etc. after adjusting the camera,

properly tighten all mounting screws.

Camera Connectors

No. Connector Definition

1Power Con-

nector (DC12V)

DC12V power connection

2Console Con-

nector

This connector is used to burn firmware into the camera when the cam-

era is returned for repair/maintenance. Please contact the camera man-

ufacturer for further information.

3RJ-45 Port For network and PoE+ connections

4Power Con-

nector (AC24V)

AC24V power connection (see Power Connector, p. 3 below)

5BNC* For analog video output (available only with max. 2 activated streams)

6Audio/Alarm

I/O & RS485

Connector**

Audio/Alarm I/O & RS485 connection (see Audio/Alarm I/O & RS485 Con-

nector, p. 4 below)

2 / 9

No. Connector Definition

7Reset Button Press the button with a proper tool for at least 20 seconds to restore

the system.

8SD Card Slot Insert the SD card into the card slot to store videos and snapshots. Do

not remove the SD card when the camera is powered on.

*Contact the manufacturer for a compatible BNC cable.

**Do NOT connect external power supply to the alarm I/O connector of the camera.

NOTE!

nTo purchase a power adapter, please contact MOBOTIX for further information.

nThe DC12V power jack and the AC24V power connector cannot be used at the same time

without causing unforeseeable damage.

microSD Card Slot/Reset Button

The positions of microSD card slot and default button are shown in the figure above.

microSD Card Slot

Insert the microSD card into the card slot to store videos and snapshots. Do not remove the

microSD card when the camera is powered on.

NOTE! It is not recommended to record with the microSD card for 24/7 continuously, as it may

not be able to support long-term continuous data read/write. Contact the manufacturer of the

microSD card for information regarding the reliability and the life expectancy.

Reset Button

Press the default button with a suitable tool for at least 20 seconds to restore the system.

Power Connector

Pin Definition

1AC24V L

2GND

3AC24V N

Camera Cabling

Power Connection

To power up the camera, connect the DC12V or AC24V power adaptor to the power connector of the

camera and the power outlet. Refer to the diagram and pin definition below for AC24V power con-

nection.

Quick Installation 2MP Speed Dome Low Light Camera

3 / 9

Quick Installation 2MP Speed Dome Low Light Camera

Alternatively, you can use an Ethernet cable and connect it to the RJ-45 port of the camera and a

PoE+ switch (Class 4).

Zero Downtime Power Switching (ZDT)

When users connect DC12V power jack and the RJ-45 port at the same time, the power input comes

from the DC12V connector. If the DC12V power source fails, the camera will switch power input seam-

lessly to the RJ-45 port until the DC12V power source is restored.

Ethernet Cable Connection

Connect one end of the Ethernet cable to the RJ-45 connector of the All-in-One cable, and plug the

other end of the cable to the network switch or PC.

NOTE!

nIn some cases, an Ethernet crossover cable may be needed when connecting the camera dir-

ectly to the PC.

nCheck the status of the link indicator and the activity indicator LEDs of the switch. If the LEDs

are unlit, please check the LAN connection.

nGreen Link LED indicates good network connection.

nOrange Activity LED flashes for network activity indication.

NOTE! The ITE is to be connected only to PoE networks without routing to the outside plant or

equivalent description.

Audio/Alarm I/O & RS485 Connector

Please refer to the diagram and pin definition tables below for using the audio/alarm I/O & RS485 con-

nection.

Pin Definition

1Audio Out

2GND (Audio I/O)

3Alarm Out A1

4Alarm Out A2

5Alarm Out B1

6Alarm Out B2

7RS485 D+

8RS485 D-

4 / 9

Pin Definition

9Alarm In 4

10 Alarm In 3

11 Alarm In 2

12 Alarm In 1

13 GND (Alarm I/O and RS485)

14 Audio In

Camera Installation Notice

NOTE! For safety reasons, it is recommended to hook up the camera's anti-drop ring ① with the

anti-drop chain ② of the pendant when installing the camera. For more information about the

pendant and anti-drop chain, please contact MOBOTIX.

Accessing the Camera

The 2MP Speed Dome Low Light Camera supports all current browsers without requiring any addi-

tional plug-ins or add-ons (e.g. for H.264/H.265/MJPEG support).

Camera Login

The default IP address of the camera is: 10.x.x.x. By default, the camera starts as DHCP client and

automatically tries to get an IP address from a DHCP server.

Quick Installation 2MP Speed Dome Low Light Camera

5 / 9

Quick Installation 2MP Speed Dome Low Light Camera

1. Enter the camera’s IP address in the URL bar of the web browser and hit “Enter”.

2. Enter the default username (admin) and password (meinsm).

NOTE! User names and passwords are case sensitive.

3. You will be prompted to set a new admin user password.

NOTE! The password can have between 6 and 16 characters (at least one digit, no special char-

acters allowed).

4. After setting a new password, you will be prompted to log in again. Remember to use the new

password.

Browser-Based Viewer

The main page of the IP camera user interface is shown as the figure below. The function buttons

vary depending on the camera model.

6 / 9

Camera Maintenance

It is recommended that you perform the following maintenance tasks at regular intervals to keep

the 2MP Speed Dome Low Light Camera in good working condition:

nClean the using plain water and a soft cloth.

CAUTION! Do not use any detergents or alcohol to prevent damage to the coating!

nCheck the mounting and make sure that all screws are properly tightened to prevent the cam-

era from falling down.

nWhen opening the camera, add a silca gel dry pack to prevent condensation accumulating at

the .

Quick Installation 2MP Speed Dome Low Light Camera

7 / 9

Quick Installation 2MP Speed Dome Low Light Camera

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente