Modecom MC-WR11 Manuale utente
1
user’s manual
www.modecom.eu
2
Wireless router
User’s manual guide 4
Chapter 1 Introduction 4
Features 4
1.2 Operation Environment 5
1.3 System Requirements 6
Chapter 2 Hardware Installation 6
2.1 Led indicators 6
2.2 Back Panel Features 6
2.3 Typical install 7
Chapter 3 Quick Install Guide 8
3.1 TCP/IP Settings 8
3.2 Getting Started 9
3.3 Setup Wizard 10
Contents
3
Wireless router
Chapter 4 Advanced Setup 18
4.1 Wireless Advanced setup 18
4.2 Service Setup 21
4.3 Security Setup 24
4.4 QoS Setup 29
4.5 Router Setup 29
4.6 System 30
www.modecom.eu
4
Wireless router
User’s manual guide
Latest versions of manuals, quick start guides, drivers and software are avail-
able on www.modecom.eu website.
IMPORTANT NOTE:
Provided technical specications are subject to change without prior notice. All
brand and product names mentioned in this manual are trademarks and/or reg-
istered trademarks of their respective holders.
© 2010 MODECOM S.A.
All rights reserved. Duplication and copying requires approval from copyright
holder.
Chapter 1 Introduction
Congratulations on your purchase of this outstanding Wireless Router. The
Wireless Router integrates 4-port switch, rewall, NAT-router and Wireless
Access Point. This product is specically designed for Home networks and
Medium or Small Corporation needs. It will allow you to connect your network
wirelessly better than ever, sharing Internet Access, les and fun, easily and
securely. It is easy to congure and operate even for users without wide ex-
perience with network devices. Instructions for installing and conguring this
product can be found the manual delivered with the product and also available
at www.modecom.eu website. Before you install and use this product, please
read this manual carefully to exploit all the functions of this product.
Features
WAN: Gateway / Bridge / WISP / Static IP / DHCP / PPPoE / PPTP / L2TP /
UPnP
LAN: RJ45 4port switch / DHCP Client, Server / Static DHCP / IP&MAC Bind
Wireless: Compliant with draft IEEE 802.11n standard (MC-WR22- 2T2R / MC-
WR11 – 1T1R)
Up to: 300Mbps (MC-WR22) / 150Mbps (MC-WR11) data transfer rates in IEEE
802.11n mode
Backward compatible with IEEE 802.11b/g
Supports both Infrastructure and Ad-Hoc Networking Modes
Work modes: AP / Client / WDS / AP+WDS / Universal Repeater (AP+Client)
Supports WPS, WPA2 (802.11i), WPA, WPA2/WPA Mixed, 802.1x advanced
security
Supports 64/128-bit WEP Data Encryption
5
Wireless router
Quality of Service (QoS) - WMM, WMM-PS
Auto wireless transmission channel select for optimal performance
Wireless access control (MAC address lter)
Advanced Wireless control:
Fragment Threshold / RTS Threshold / Beacon Interval
Preamble Type: Long / Short
IAPP - Roaming (802.11f)
Protection / Aggregation / Short GI / WLAN Partition
RF Output Power control
Multiple BSSID
Dynamic DNS:
DynDNS.org / TZO / 3322.org
NAT:
NAT/NAPT IP sharing / DMZ / Port Forwarding / Port Trigger / UPnP
QoS:
Yes - IP (single or range) Grant MIN or MAX bandwidth
Firewall protection:
Ping Access on WAN / IGMP Proxy / Web Server Access on WAN / IPsec/
PPTP/L2TP VNP pass through /
Src MAC or IP Filter / URL Filter / Dst IP and Port Filter /
DoS Prevention:
Whole System Flood: SYN, FIN, UDP, ICMP
Per-Source IP Flood: SYN, FIN, UDP, ICMP
TCP/UDP Port Scan (High/Low Sensitivity)
ICMP Smurf, IP Land, IP Spoof, IP TearDrop, PingOfDeath, TCP Scan, TCP
SynWithData, UDP Bomb, UDP EchoChargen
Source IP Blocking (Block for a specied time)
System Management:
Access Schedule / NTP support / FW Upgrade / Save/Load Cong / Reboot /
User name and password management
1.2 Operation Environment
Dimensions: 202 (L) x 120 (W) x 31 (H)mm
Unit Weight: 324g
Power Input: 9V DC, 1A
Consumption: 13.5W(Max)
Storage Temperature: -40ºC ~70ºC
www.modecom.eu
6
Wireless router
Operating Temperature : -10ºC ~50ºC
Storage Humidity: 5% ~95% RH Non-condensing
Operating Humidity: 10% ~90% RH Non-condensing
1.3 System Requirements
An Ethernet-Based Cable or DSL modem
10/100M Ethernet Card on PC
TCP/IP network protocol for each PC
RJ45 Twisted-pair cable
Internet browser: Microsoft Internet Explorer, Firefox, Opera or Chrome
Chapter 2 Hardware Installation
2.1 Led indicators
SYS/Power (Red): Flickering light indicates a proper connection to the power
supply.
While resetting the SYS LED will ash differently (shine for 2 seconds and stop
for 1 second).
WPS (Green): The Led will icker for about two minutes when WPS session
is active .
WLAN (Wireless LAN) (green): The LED is ickering during wireless activity.
LAN 1,2,3,4 (green): The Link/Act LED serves two purposes. If the LED is con-
tinuously illuminated, the Router is successfully connected to a device through
the corresponding port. If the LED is ickering, the Router is actively sending or
receiving data over that port.
WAN (Green):The Link/Act LED serves two purposes. If the LED is continu-
ously illuminated, the Router is successfully connected to a device through the
corresponding port. If the LED is ickering, the Router is actively sending or
receiving data over that port.
2.2 Back Panel Features
7
Wireless router
LAN(1,2,3,4): 10/100Mbps RJ45 Auto-sensing. These four LAN ports are
where you will connect other network devices, such as PCs/Laptops, print
servers, remote hard drives, and anything else you want to put on your net-
work. If you connect this product with the Network adapter, Hub (or Switch)
correctly, the Router’s corresponding LED and the Adapter’s, Hub’s (or the
Switch) will illuminate.
WAN: 10/100Mbps RJ45 port. The WAN port is where you will connect
Cable/DSL Modem or other LAN.
RESET(WPS): The Reset Button has three functions, WPS, reboot and
Factory Default. When press it less than 2 second, it is WPS function and
the SYS LED will ash two minute (as long as WPS session is active); 2 to
5 seconds, the router will reboot; and more than 5 seconds, the router will
restore to factory default settings.
Power inlet: 9V DC, 1A Power supply.
2.3 Typical install
1. Make sure all devices, including your PCs, modem, and Router, are
turned on.
2. Using an Ethernet network cable, connect the LAN device or Ethernet
network port of the cable or DSL modem to the Router’s WAN port.
www.modecom.eu
8
Wireless router
Chapter 3 Quick Install Guide
3.1 TCP/IP Settings
Before you can access and congure router, you have to setup your net-
work adapter IP address. According to the following steps to obtain IP ad-
dress automatically from router DHCP Server, The following instruction set
up the computer running windows operation system.
Note: The router default IP address is 192.168.1.1
1. Click Start button and choose Settings, then click Control Panel.
2. Double click Network icon and select Conguration tab in the Network
window.
3. Choose the connection you want to use and click it with right mouse but-
ton and choose “Properties”.
4. Double click TCP/IP Protocol.
5. Make sure that option “Obtain IP address automatically” is chosen.
8. Click OK to complete the install procedure.
After all is successful, you can check the TCP/IP information via the follow-
ing command. Start -> run. Type cmd and in the window like the one below
enter command: ipcong /all.
9
Wireless router
3.2 Getting Started
To access conguration panel open your web browser (MS Internet Explorer,
Firefox, Opera or Chrome) and type the router’s IP address: 192.168.1.1
Default User / Password: admin
If successful, you can see the status page.
www.modecom.eu
10
Wireless router
3.3 Setup Wizard
Click on “Wizard”, it will guide you to setup your router in six simple steps.
Please follow the steps and complete the router conguration.
Step 1 - Setup Operation Mode
The router supports three operation modes, Gateway, Bridge and Wireless ISP.
And each mode is suitable for different use, please choose correct mode.
Altri manuali per MC-WR11
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Modecom Router wireless
