Molex 63816-0900 Manuale utente

AT Crimp Head Adapter For Battery Powered Crimp Tools

Doc No: ATS-63816 9 Release Date: 5-2 -11 UNCONTROLLED COPY Page 1 of 2

Revision: A Revision Date: 5-2 -11

AT Crimp Head Adapter

For Battery Powered

Crimp Tools

Application Toolin

Specification Sheet

Order No. 63816-0900

Features

 Quick change Crimp Head adapter is easily installed onto Battery

Power Crimp Tool (Order No. 63816- 2 )

 Powered crimp tools help reduce fatigue and discomfort from

repetitive manual crimping and allows portability

 A precision user-friendly terminal locator wire stop holds terminals in

the proper crimping position

SCOPE

The 63816- 9 Crimp Head Adapter was created for use with the

64 5 and 64 7 series AT Crimp Head assemblies when the Battery

Powered Tool (Order No. 63816- 2 ) is preferred over the AT-2

Pneumatic tool.

Installation

To install the Crimp Head Adapter onto the Battery Powered Tool,

(Order No. 63816- 2 ), refer to the Instruction Manual TM-63816 2 ,

Section 3, “Set-Up and Adjustments”.

Install the AT Crimp Head to the 63816- 9 Crimp Head Adapter,

using the two slotted screws that are used to fasten the head to the AT-

2 Pneumatic Actuator. See Figure 1.

CAUTION: Never place fingers into the tooling nest.

Operation

1. To load a terminal and position the wire in the terminal in the Power Crimp Head, follow the loading procedure

as explained in the AT Air Powered Crimp Tool Head instruction sheet.

2. Crimp the terminal by squeezing the trigger on the side of the battery actuator until the tool cycles and returns

and the jaws open.

3. Remove the terminal from the locator and inspect the crimp for proper quality.

AT CRIMP

HEAD

ADAPTER

BATTERY

POWERED

TOOL

LOCKING

PINS (2)

Fi ure 1

AT CRIMP

HEAD

ASSEMBLIES

SLOTTED

SCREWS (2)

AT Crimp Head Adapter For Battery Powered Crimp Tools

Doc No: ATS-63816 9 Release Date: 5-2 -11 UNCONTROLLED COPY Page 2 of 2

Revision: A Revision Date: 5-2 -11

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance

steps:

1. This tool was engineered for durability, but like any fine piece of

equipment, it needs cleaning and lubrication for a maximum service life

of trouble-free crimping

2. Remove dust, moisture and other contaminants with a clean brush, or

soft, lint-free cloth.

3. Do not use any abrasive materials that could damage the tool.

4. Make certain all pins, pivot points and bearing surfaces in the tool head

are protected with a thin coat of high quality machine oil. Do not oil

excessively. The use of a light oil, such as SAE 3 weight automotive

oil, every 5, crimps or monthly, will significantly enhance the tool life

and ensure a stable calibration. See Figure 1 for lubrication points.

5. Store the tool in a clean and dry area when not in use.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made

of the best quality materials. All vital components are long life-tested. All tools are warranted free of manufacturing

defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool, free of charge.

This repair or exchange will not be applicable to altered, misused, or damaged tools.

http://www.molex.com

LUBRICATION

POINTS

(BOTH SIDES)

LIGHT OIL

(EVERY MONTH

5,000 CRIMPS)

Fi ure 1

Indice

Altri manuali molex Utensili per crimpatura

molex

molex 11-01-0101 Manuale utente

molex

molex 63827-6900 Manuale utente

molex

molex 63816-0800 Manuale utente

molex

molex 63811-1500 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 64001-7400 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63825-2600 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63823-5570 Manuale utente

molex

molex ServiceGrade 64016-0036 Guida utente

molex

molex 63811-8100 Manuale utente

molex

molex 63825-6070 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63825-9670 Manuale utente

molex

molex 63819-0600 Manuale utente

molex

molex 63825-5000 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63811-6800 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex ServiceGrade 64016-0038 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente

molex 63816-0900 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche